The ONLY magazine loader that has worked for me; to load the Sig 365x magazines is the Speed Beez. The Sig 365 mags are one of the hardest magazines to load as everything on this pistol is compact including the magazine. The ETS works well for compact Glocks but not for the Sig.
I genuinely thought I was a bitch from the pain of loading. Glad I am not the only one who thinks it sucks lololol. I always call BS when in movies they dump a box and slap in a few rounds real quick hahahaha.
I had an issue with that too... But seriously though?... Practice makes perfect... You just need to push down with your thumb, with your OTHER THUMB on top of your thumb... And you really only need to do this to the LAST round, maybe the last 2... Also, pull the round back as your pushing down to seat it. Hope this helps, save yourselves some money and just practice... I'm 5'8 and 115 pounds and have no problems loading these 12 round mags
Don't give up on the ETS Camloader. I had the same problem with my Taurus G2S mags. Then, I noticed that the mag follower was not perfectly centered because the mag thickness was less than the opening width of the ETS. The issue is that the ETS is designed for mags with different widths. My "high tech" solution was to cut some cardboard from a Browning ammo box and tape them to the insides of the ETS mag loading chamber. That narrowed the width so that when the magazine was inserted it was now perfectly centered; made it much easier. Also, you are correct, lubing the loader grooves makes it easier. Once you get the hang of it, the ETS speedloader is much faster. I also have a Uplula type loader which I use for my lower capacity mags. Hope this helps.
Beware there are fake Uplulas out there...i got one that seemed to be goo good of a deal $17. Looked real, but after a few uses with P365 it bent and won't get last few in my new 12 rd magazine, gotta look fir another now
I watched another video before yours and the gentleman that didn't jam one first put it on his chest and loaded 70 some rounds in a matter of seconds! He even mentioned that it worked better than putting it on the table top.
The 2nd one is the one I have and it works great!! I tried loading the magazine at the shop when I bought my weapon and I was embarrassed as hell when I couldn’t get past the 1st bullet….the P365 mags are ridiculously hard to load- I have 4 and have issues with all 4….
The demo I watched from ETS said repeatedly you should flip the ammo up right away so that the tips face the ceiling, otherwise it binds like what you demonstrated. I had the same issue.
Also, not sure, but I believe you might have to oil it every use. When I was at the range I tried using it and it wasn't oiled and it jammed up on me several times. When I got home and applied oil to the two spots, it worked fine.
I wish I would have seen this video sooner. I also purchased the ETS speed loader and had trouble loading a new P365 magazine. I found if you install the magazine first until it clicks into place and then pick up about 5-7 rounds at a time it works a lot better then trying to load the 10 rounds as advertised. Hopefully this info would helpful so that the ETS isn't as disappointing cause when it do work it is pretty impressive.
SO i had a very similar experience to you. I am not really giving up on the ETS because when it does work it works amazing. It works very well on full sized double stack mags. Anything micro compact and it's a hit or miss. Doing 5 or so rounds at a time yields faster results
Uplula is good. I have two. On ETS, it did not appear to me you fully seated mag first. Then after you jammed it, tried it on your chest. Naturally, it didn't do anything, you had already jammed it. ETS also recommends oiling a couple of spots first, not the rail on both sides. Read instructions first.
Ha! I’m glad it wasn’t just me. Took my P365 to the range for the first time today and could only get 4-5 rounds per magazine. I guess I got spoiled with my Shield EZ. Uplula is on the way, should improve the shooting experience going forward.
I bought the XL today and I was dumbfounded when I couldn’t fully load the 12 round mags. I’m 6’2 295 lbs and I’m not normally a puss like this. 😆 I actually loaded 10 rounds in one Mag the first time and thought, something wasn’t right but then I was taken back when I could only force about 6 rounds in it the second time. I did manage to load 12 in the other mag once but that’s it. I’m buying the Uplula tomorrow. I’m fine with being called a puss. 😁
that's pretty funny. I bought a p365 two days ago and i couldn't believe how much i was struggling to load the mag. All i could think of was that there was a second mag I had to load after! The 2nd mag isn't loaded yet....
I got mine to work by only doing 1-3 rounds at a time. Pressing against my chest as shown by you. Much more pressure required compared to a glock mag, but doable.
I would recommend the speed bees p365 speed loader, I just got mine and its 10/10. It does have a problem with dry fire dummy rounds but with live rounds no problem.
Why, oh why does the 365 mag spring have to be so tight? I saw a video with the Speed Beez, and purchased one. Worked like a charm...very well built and easy to use, unlike a few other Speed loaders I bought.
Try loading the magazine in first & smacking the bottom to make sure its fully seated & then try loading in the bullets for the ETS. If that doesn't work, try the same thing but with 1 bullet already loaded. Should work.
I redact my statement, my ETS finally came in and the P365 mags are a nightmare to try to get to work. Oiled up the ETS, followed directions and no dice, gets jammed. Uplula for this one
Dude, you gotta follow the directions for the ETS. The clip wasn't all the way in & you need to hold it so the ramp is parallel to the ground. Also, you need to oil the internal ramps where the rounds pass through into the magazine like the instructions call out. I've got one and it works great.
I bought an after market speed loader of Amazon to try, I had the same problem with jamming. I found that if you put the mag in first, then load the speed loader with desired number of rounds then place it against level against you chest (Leaving a little gap) before ammo touches the mag worked pretty good!
Oil or any kind liquid lubricant works well for a little while, but it tends to get gummed up over time, I use graphite dry lube that you can buy for locks, I sprinkle some on a sheet of paper then use a quarter inch wide flat brush to brush it into the recommended areas.. works great and lasts for quite a while. I've never had a problem since.
“Maglula UpLULA Universal Pistol Magazine Speed Loader.” Problem solved. I am NOT affiliated! I’ve owned them for years. I paid ~$35 total for a new one to go in the case with the 365. I own 5 of the Sig 365 mags. 2 from factory with pistol and 3 purchased extra. Absolute PTA to load! First 3 or 4 rounds are OK. Then, forget about it! In all 5 mags! This is not my first rodeo. I've used one, but never EVER “needed” a speed loader in my life, until now. Worst loading mags ever. $50 a pop! Great pistol.
Tested this out on my buddy’s P365, I had no problems with the ETS I bought. But I do agree with the tension and the short mag. If you still have em, try again but with the rounds facing up or vertically towards the sky/ceiling rather than towards a wall or horizontal. Basically have gravity help the rounds drop in the mag as you’re plunging them in. This made all the difference for us when performing our tests along with the oil coating you showed. If done correctly it can beat the UpLula. UpLula is great and requires little technique to load. Our group uses both so the it’s kind of a tie. Most of the ladies prefer the UpLula for the simplicity of it. After some practice with the ETS, you’ll see the difference in loading efficiency. My technique: With the rounds facing up after the scoop, personally use my hip as a brace rather than my chest, then I plunge. Great vid by the way! Thumbs up!
Oh and another couple tips in regards to the ETS, try doing 5 rounds first to get the feel or you can try prepping the mag with one round already in it, or split your scoops (6 then 6 for 12 mag, 5 and 5 for 10). I can buy em off of you so they don’t go to waste. $30 for both. 😬 Haha
You have to read the directions. You will see the recommended spots to lube. You have to lube the inside of the loader. Load a few times to break it in.
Just got my ETS yesterday for my Taurus G2C and my chest is bruised from trying to load my magazine with the "against your chest method" It seems I can load 5/6 rounds at a time but any more and it does what yours was doing in the video, binding up.
I have an ETS speedloader for pistols, and a separate one for rifles, and they work well as long as the magazine doesn't have super stiff springs like the P365. I also have the Maglula, which I love for my Beretta 92F, Glock 45, & Tauraus G2C 9mm, but not for the P356, or my single stack Colt 1911 45 ACP, Remington RM380 or Tauraus G2C 40 S&W. In fact, in the middle of loading my 9 P365 mags, my Maglula's metal push bar bent, and was never strong enough to load the P365 mags again. I don't think is was the stiff springs alone--the fact that the P365 mag is NOT double stack (it's a patented 1 1/2 stack) which wobbles in the Maglula IMHO both contributed to the failure of the Maglula (which was replaced under its 1 year warranty. I bought the MAKERSHOT Speedloader for Sig Sauer P365 on Ebay, and it works great for me.
I saw the Makeshot as well, but it's my understanding that its is a 3D printed product which makes me second guess the quality. I hope it works well for you and last a good long while.
Try loading one round into the mag then use the ETS, it seems to fix the jamming issue for me, and oil the inside feed ramp also. I also use the Uplula too.
I had the same problem with the ets and amost gave up, with my P365!!! First check where the bullets slide into the rail mine had some burs from factory or from me not sure. So I ran some sand paper in the groves and got it smooth. Then make sure that it is horizontal with the bullets facing up and it should work good. It took me about 5-10 mags to get it broken in and now it’s fine. Also if you doing a lot of mags put a towel folded up as a cushion on your chest! It’s not perfect but I’d say it’s 85-90% now!
Loook into the company plate. They make a loader that looks just like the ets but, it's better fitted to sig mags. I only load about 5 rounds at a time. It does work better than the ets version.
Awesome video! Thank you. Just out of curiosity, did your magazines ever become easier to load after shooting a few rounds or is this just a p365 issue?
GodMusicLovePeace That’s a good question to ask. I’ve had a Beretta .40 cal for about 30 yrs and the springs eventually loosened up. I get a “stovepipe” jam and misfeed occasionally. But I’m curious as a new P365 owner as well about these mags. These puppies are tight! Lol. Which is why I’m appreciative of this video. I’m hitting Amazon to order right now with my bruised fingers! So, thanks all!
@@secondwind75 I must say after shooting a few rounds through my sig my mags have become easier to load. When I first started I could barely manually load past 4 bullets. It would take me like 20 minutes 😯 Unless, I've gotten super strong in a short period of time I've had no issues a of late.
Mine works great on my single and double stack 9mm mags. Just a drop of oil on the slide and another on the internal ramp and I'm good for many loads. Just seat mag tight, scoop up rounds, turn over with the bullet tip up and draw in the plunger. Simple.
I did the same with my 365...very hard to load...All except this loader...Caldwell...I can load ANY mag and round of any gun. Where have you been all my life..all adjustable..no need for all the other sit...loads any thing..bought mine at bass pro..43$..threw all others in trash..wife loves it also..you cant go wrong
You oiled the WRONG part of the ETS. You need to oil the INSIDE RAMP that the bullets ride on before going into the magazine. Otherwise, it will get “stuck”.
I did the same thing (except for buying 2). I bought one for my P320 mags and it sucked. I almost threw it away until it worked OK with my Staccato mags. But, I have 3 Staccato mags and like 30 P320 mags.
P.S. All the P365 mag issues I was having seam to stem from the follower on the magazine. It's edges are very sharp and catch on the mag release holes. Need to grind them down a little. Ive show a few hundred rounds and it's gotten a lot better.
Marclevy7567 , I beg to differ with you. I just received my ETS speed loader and I’m having the same exact issue and I did load the magazine into the speed loader first as far as it would go. I tried many times even followed any and all suggestions I could find on CZcams. This particular speed loader just doesn’t work for the P365 mags. But I also have to say I struggled with the Glock 19 mags as well but did have success with them. P365 mags were a def fail.
Hey, I got it to work, Problem, the magazine does not full sits to the top of the loader lips. Solutions, shave off the second ledge to full seat the magazine
Load 3-4 rounds at a time and it will work without a problem. I have the same loader and I had similar problems until I reduced the amount I was loading.
Your problem is technique. Your ets will work for your sig. You just need to know the secret. Watch my short on speed loading. I am doing a review of the ets tomorrow to explain the secret. No lube needed. It helps but not needed
I'ma senior citizen and loads mags isnt ever easy. My fingers are trashed from first try with new P365. Used my Glock ' "speed loader" it is OK. could not get the 10th one in.. I think ill get this Uplula
You jammed it when you attempted using the table top. Try again using your chest. Place the magazine in the ETS loader first. Then load your ammunition into the loader. Keep the ammunition pointed upwards and placed the magazine against your chest and push quickly and firmly on the plunger. I have done this 1000 times or more and have never had a problem. I also know many other people who do not have a problem. But if you load the ammunition and turn it in direction other than up before you put the plunger on it and put it on your chest the first one or two bullets jam because they’re not straight and tight against the magazine
Does sig not come with a loader? My g48 did I just assumed most manufacturers include them. The one that came with isn't as fast for sure. But it still saves the fingers.
Operator error!!! You must put the magazine in BEFORE loading the ammo! If the mag is not seated first the bullets become mis aligned below the sight line of the loader body. If you seat the mag FIRST to the second stop not the first it works every time!! The instructions are not too clear. Alto make sure the pusher touches the body of the loader when you push it down or you won't get the last round to load. It is a wonderful gadget once you know how to use it. Also DON't slap the mag into the loader but push it. If you keep slapping it you will damage it. Push the mag in till you feel the second notch or seat. I had the same problem you did till I took some time to figure it out.
@@cameronandgunnyhigdon No I don't have a Sig P365 to try. What i do know is he put the oil in the wrong place and didn't seat the magazine properly. He should go to the ETS web site and follow their directions. I couldn't get mine to load a Glock mag until I watched the video and carefully placed the oil. Mine now works perfectly. Good luck, Marc
Marclevy7567 , I beg to differ with you. I just received my ETS speed loader and I’m having the same exact issue and I did load the magazine into the speed loader first as far as it would go. I tried many times even followed any and all suggestions I could find on CZcams. This particular speed loader just doesn’t work for the P365 mags. But I also have to say I struggled with the Glock 19 mags as well but did have success with them. P365 mags were a def fail.
Not the least bit surprised by this. I bought one, sent it back, got the replacement and just threw the damn thing away. worthless as far as I am concerned. I was hopeful, but no cigar.
I have been using an UpLula for years in my auto loaders. Bought a P365 this past weekend. While using the UpLula, I found that loading the 10th round in the 10 round clip is a real b***h. I hope the spring loosens up some. Still, I love the accuracy of the P365.
I found you too late. I have the exact same problem and solution. I wish I had seen your video before I purchased the speed loader (mine was from TACNATION and it just sucks!).UPLula is the way to go. I have Canik's (their loader is good as well), sig P229 40 s&w and a couple of highpoint magazines, none of them would work. Only a Mossberg MC1 magazine with 5 rounds worked halfway with the speed loader.
hey just wanted to let you know I had the same issue and I found my resolution. i got a .380 loader for my bersa with doublestack. after staring at it for 2 days I realized i had to dremel a good mm or two off the top edges of the entry side of my mag and now it works like magic.
The ONLY magazine loader that has worked for me; to load the Sig 365x magazines is the Speed Beez. The Sig 365 mags are one of the hardest magazines to load as everything on this pistol is compact including the magazine. The ETS works well for compact Glocks but not for the Sig.
My hand was literally bruised after loading 3 magazines for my p365. Can’t wait for this to come in the mail lol
I fought with my madras for two hours before I finally got it in😂 my fingers were also bruised after
Yeah, these are gonna save my thumbs from going raw
I genuinely thought I was a bitch from the pain of loading. Glad I am not the only one who thinks it sucks lololol. I always call BS when in movies they dump a box and slap in a few rounds real quick hahahaha.
I couldn’t find the UpLULA on Amazon. Where are y’all ordering it from?
I had an issue with that too... But seriously though?... Practice makes perfect... You just need to push down with your thumb, with your OTHER THUMB on top of your thumb... And you really only need to do this to the LAST round, maybe the last 2... Also, pull the round back as your pushing down to seat it. Hope this helps, save yourselves some money and just practice... I'm 5'8 and 115 pounds and have no problems loading these 12 round mags
Don't give up on the ETS Camloader. I had the same problem with my Taurus G2S mags. Then, I noticed that the mag follower was not perfectly centered because the mag thickness was less than the opening width of the ETS. The issue is that the ETS is designed for mags with different widths. My "high tech" solution was to cut some cardboard from a Browning ammo box and tape them to the insides of the ETS mag loading chamber. That narrowed the width so that when the magazine was inserted it was now perfectly centered; made it much easier. Also, you are correct, lubing the loader grooves makes it easier. Once you get the hang of it, the ETS speedloader is much faster. I also have a Uplula type loader which I use for my lower capacity mags. Hope this helps.
Thank you for the great video. I was leaning toward the ETS for my new P365. I'm glad you save me from returning the ETS. I'll get the Uplula tonight!
I hope you like it
Beware there are fake Uplulas out there...i got one that seemed to be goo good of a deal $17. Looked real, but after a few uses with P365 it bent and won't get last few in my new 12 rd magazine, gotta look fir another now
@@FilmFlam-8008 i take both this and the uplula to the range
@@cameronandgunnyhigdon Old adage “If it looks too good to be true, it usually is”. Lol
I watched another video before yours and the gentleman that didn't jam one first put it on his chest and loaded 70 some rounds in a matter of seconds! He even mentioned that it worked better than putting it on the table top.
The 2nd one is the one I have and it works great!! I tried loading the magazine at the shop when I bought my weapon and I was embarrassed as hell when I couldn’t get past the 1st bullet….the P365 mags are ridiculously hard to load- I have 4 and have issues with all 4….
They just don’t work well with p365 mags. I can’t get them to work at all.
Man O man thankkkkkkk you so much for explaining this to me. I was really killing myself trying to load my P365😱
The demo I watched from ETS said repeatedly you should flip the ammo up right away so that the tips face the ceiling, otherwise it binds like what you demonstrated. I had the same issue.
Also, not sure, but I believe you might have to oil it every use. When I was at the range I tried using it and it wasn't oiled and it jammed up on me several times. When I got home and applied oil to the two spots, it worked fine.
The Uplula speed loader made by Maglula is great. I will never give mine up.
I wish I would have seen this video sooner. I also purchased the ETS speed loader and had trouble loading a new P365 magazine. I found if you install the magazine first until it clicks into place and then pick up about 5-7 rounds at a time it works a lot better then trying to load the 10 rounds as advertised. Hopefully this info would helpful so that the ETS isn't as disappointing cause when it do work it is pretty impressive.
The first video I watched on this ETS the guy mentioned it does not work with the p365! That's why it's always good to do some research on CZcams!
I know what your problem is. I have the ets too. There is a trick to it. It will work for your sig.
This helped thanks
SO i had a very similar experience to you. I am not really giving up on the ETS because when it does work it works amazing. It works very well on full sized double stack mags. Anything micro compact and it's a hit or miss.
Doing 5 or so rounds at a time yields faster results
Uplula is good. I have two. On ETS, it did not appear to me you fully seated mag first. Then after you jammed it, tried it on your chest. Naturally, it didn't do anything, you had already jammed it. ETS also recommends oiling a couple of spots first, not the rail on both sides. Read instructions first.
You sir are a life saver!👍
Thank you for watching
Ha! I’m glad it wasn’t just me. Took my P365 to the range for the first time today and could only get 4-5 rounds per magazine. I guess I got spoiled with my Shield EZ. Uplula is on the way, should improve the shooting experience going forward.
I bought the XL today and I was dumbfounded when I couldn’t fully load the 12 round mags. I’m 6’2 295 lbs and I’m not normally a puss like this. 😆 I actually loaded 10 rounds in one Mag the first time and thought, something wasn’t right but then I was taken back when I could only force about 6 rounds in it the second time. I did manage to load 12 in the other mag once but that’s it. I’m buying the Uplula tomorrow. I’m fine with being called a puss. 😁
that's pretty funny. I bought a p365 two days ago and i couldn't believe how much i was struggling to load the mag. All i could think of was that there was a second mag I had to load after! The 2nd mag isn't loaded yet....
I got mine to work by only doing 1-3 rounds at a time. Pressing against my chest as shown by you. Much more pressure required compared to a glock mag, but doable.
Just got mine yesterday, and it worked as expected with the Glock 17 magazines
Not only does the ETS suck, they have no customer service. I just sent mine back. I will give the other mag loader a try. Thank you
The ETS loader works great for me. Glad I'm able to use it on the P365 mags. Think it works better than on Glock and ETS mags.
I would recommend the speed bees p365 speed loader, I just got mine and its 10/10. It does have a problem with dry fire dummy rounds but with live rounds no problem.
Why, oh why does the 365 mag spring have to be so tight? I saw a video with the Speed Beez, and purchased one. Worked like a charm...very well built and easy to use, unlike a few other Speed loaders I bought.
Try loading the magazine in first & smacking the bottom to make sure its fully seated & then try loading in the bullets for the ETS. If that doesn't work, try the same thing but with 1 bullet already loaded. Should work.
I redact my statement, my ETS finally came in and the P365 mags are a nightmare to try to get to work. Oiled up the ETS, followed directions and no dice, gets jammed. Uplula for this one
Thank you. I was having trouble loading up my mags by hand. I could only load 5 rounds max. 😂😂 gotta break in the mags somehow.
Insert the magazine first before you will hear "click"... 🤣
Dude, you gotta follow the directions for the ETS. The clip wasn't all the way in & you need to hold it so the ramp is parallel to the ground. Also, you need to oil the internal ramps where the rounds pass through into the magazine like the instructions call out. I've got one and it works great.
It works with the P365 magazines?
@@Lawton-Talks No idea,I run a G17
I bought an after market speed loader of Amazon to try, I had the same problem with jamming. I found that if you put the mag in first, then load the speed loader with desired number of rounds then place it against level against you chest (Leaving a little gap) before ammo touches the mag worked pretty good!
@Robert That's CRAZY!! Wait... You literally just commented what the directions say, almost word for word. You've really cracked the code bud! 🤣
Oil or any kind liquid lubricant works well for a little while, but it tends to get gummed up over time, I use graphite dry lube that you can buy for locks, I sprinkle some on a sheet of paper then use a quarter inch wide flat brush to brush it into the recommended areas.. works great and lasts for quite a while. I've never had a problem since.
This works wonders on the P365. The dang spring is just so tight in those mags.
“Maglula UpLULA Universal Pistol Magazine Speed Loader.” Problem solved. I am NOT affiliated! I’ve owned them for years. I paid ~$35 total for a new one to go in the case with the 365. I own 5 of the Sig 365 mags. 2 from factory with pistol and 3 purchased extra. Absolute PTA to load! First 3 or 4 rounds are OK. Then, forget about it! In all 5 mags! This is not my first rodeo. I've used one, but never EVER “needed” a speed loader in my life, until now.
Worst loading mags ever. $50 a pop!
Great pistol.
Tested this out on my buddy’s P365, I had no problems with the ETS I bought. But I do agree with the tension and the short mag. If you still have em, try again but with the rounds facing up or vertically towards the sky/ceiling rather than towards a wall or horizontal. Basically have gravity help the rounds drop in the mag as you’re plunging them in. This made all the difference for us when performing our tests along with the oil coating you showed. If done correctly it can beat the UpLula. UpLula is great and requires little technique to load. Our group uses both so the it’s kind of a tie. Most of the ladies prefer the UpLula for the simplicity of it. After some practice with the ETS, you’ll see the difference in loading efficiency.
My technique: With the rounds facing up after the scoop, personally use my hip as a brace rather than my chest, then I plunge.
Great vid by the way! Thumbs up!
Oh and another couple tips in regards to the ETS, try doing 5 rounds first to get the feel or you can try prepping the mag with one round already in it, or split your scoops (6 then 6 for 12 mag, 5 and 5 for 10). I can buy em off of you so they don’t go to waste. $30 for both. 😬 Haha
He threw the directions out when he unboxed it. 😂 as a man I understand this instinct.
Ive go the UpLula it does a fine job ive never seen the other Great video
I tried all the suggestions and could not get it to work with the sig p365. I am glad I am not alone.
UpLula has been the gold standard for a looong time. Just bought another one for $24.99, they're worth every penny.
You have to read the directions. You will see the recommended spots to lube. You have to lube the inside of the loader. Load a few times to break it in.
I Love my uplula. It May be the Best money I ever spent on anything. It’s always in my range bag.
Thanks I was trying to decide which to get
Great video👀
Just gone one of these, works perfectly with the P365 mag.
What exactly is it called and where’d you buy it?
@@thomasjohnson4217 ETS CAM Speed Loader ETSCAM-9-40. Search using that term on Amazon.
Just got my ETS yesterday for my Taurus G2C and my chest is bruised from trying to load my magazine with the "against your chest method" It seems I can load 5/6 rounds at a time but any more and it does what yours was doing in the video, binding up.
I'm glad I found this, as a first time gun owner!
Me too
I have an ETS speedloader for pistols, and a separate one for rifles, and they work well as long as the magazine doesn't have super stiff springs like the P365. I also have the Maglula, which I love for my Beretta 92F, Glock 45, & Tauraus G2C 9mm, but not for the P356, or my single stack Colt 1911 45 ACP, Remington RM380 or Tauraus G2C 40 S&W. In fact, in the middle of loading my 9 P365 mags, my Maglula's metal push bar bent, and was never strong enough to load the P365 mags again. I don't think is was the stiff springs alone--the fact that the P365 mag is NOT double stack (it's a patented 1 1/2 stack) which wobbles in the Maglula IMHO both contributed to the failure of the Maglula (which was replaced under its 1 year warranty. I bought the MAKERSHOT Speedloader for Sig Sauer P365 on Ebay, and it works great for me.
I saw the Makeshot as well, but it's my understanding that its is a 3D printed product which makes me second guess the quality. I hope it works well for you and last a good long while.
I dont think u inserted the mag all the way
You have to press mag hard to seat it, I've got know issues.
I use it for my FN 509 and it works just fine.
Nice video! I like my uplula loader
Try loading one round into the mag then use the ETS, it seems to fix the jamming issue for me, and oil the inside feed ramp also. I also use the Uplula too.
I had the same problem with the ets and amost gave up, with my P365!!! First check where the bullets slide into the rail mine had some burs from factory or from me not sure. So I ran some sand paper in the groves and got it smooth. Then make sure that it is horizontal with the bullets facing up and it should work good. It took me about 5-10 mags to get it broken in and now it’s fine. Also if you doing a lot of mags put a towel folded up as a cushion on your chest! It’s not perfect but I’d say it’s 85-90% now!
Also oil is the key!!!!!
thanks for the vid!
Glad to help
For that gun the SpeedBeez loader is best. That's why SIG sells them on their website.
OMG, thank you!
I have one. Love it so much
Loook into the company plate. They make a loader that looks just like the ets but, it's better fitted to sig mags. I only load about 5 rounds at a time. It does work better than the ets version.
Awesome video! Thank you.
Just out of curiosity, did your magazines ever become easier to load after shooting a few rounds or is this just a p365 issue?
Every P365 I’ve shot regardless of age is hard. Honestly, that’s only like four P365’s but still...
GodMusicLovePeace That’s a good question to ask. I’ve had a Beretta .40 cal for about 30 yrs and the springs eventually loosened up. I get a “stovepipe” jam and misfeed occasionally. But I’m curious as a new P365 owner as well about these mags. These puppies are tight! Lol. Which is why I’m appreciative of this video. I’m hitting Amazon to order right now with my bruised fingers! So, thanks all!
@@secondwind75 I must say after shooting a few rounds through my sig my mags have become easier to load.
When I first started I could barely manually load past 4 bullets.
It would take me like 20 minutes 😯
Unless, I've gotten super strong in a short period of time I've had no issues a of late.
@@GodMusicLovePeace Glad to hear. Thanks.
Thank you, thank you , thank you!
The Maglula works first time, every time.
Mine works great on my single and double stack 9mm mags. Just a drop of oil on the slide and another on the internal ramp and I'm good for many loads. Just seat mag tight, scoop up rounds, turn over with the bullet tip up and draw in the plunger. Simple.
Thank you so much. I just got a speed loader on Amazon and it did not work. I wish I saw your video first.
How could you not use the ETS? Just sell me both of your used ETS so I can give it to my mom and sister.
He wasn't fully seating the magazine like he "said" he was doing.
My p365x mags were engaging too far on the ETS, I made a pvc spacer that holds the mag out about 1/8 of an inch. It works great now
I did the same with my 365...very hard to load...All except this loader...Caldwell...I can load ANY mag and round of any gun. Where have you been all my life..all adjustable..no need for all the other sit...loads any thing..bought mine at bass pro..43$..threw all others in trash..wife loves it also..you cant go wrong
You oiled the WRONG part of the ETS. You need to oil the INSIDE RAMP that the bullets ride on before going into the magazine. Otherwise, it will get “stuck”.
I did the same thing (except for buying 2). I bought one for my P320 mags and it sucked. I almost threw it away until it worked OK with my Staccato mags. But, I have 3 Staccato mags and like 30 P320 mags.
P.S. All the P365 mag issues I was having seam to stem from the follower on the magazine. It's edges are very sharp and catch on the mag release holes. Need to grind them down a little. Ive show a few hundred rounds and it's gotten a lot better.
Works perfect with P229 40cal also
Super hard to load is an understatement. Only bad thing about the gun though...
IOU a beer. Thanks for this!
Marclevy7567 , I beg to differ with you. I just received my ETS speed loader and I’m having the same exact issue and I did load the magazine into the speed loader first as far as it would go.
I tried many times even followed any and all suggestions I could find on CZcams.
This particular speed loader just doesn’t work for the P365 mags.
But I also have to say I struggled with the Glock 19 mags as well but did have success with them. P365 mags were a def fail.
You're using the UpLula backwards, of you turn it around, it's way faster.
thank you!!!!!
Do you have the part/producty number for the Uplula for the P365 magazines. I went to my local gunstore and there were many to choose from.
Maglula UpLula UP60B Pistol Magazine Loader, I found it on Academy Sports for $30. The B is for black, there are other colors available.
Hey, I got it to work,
Problem, the magazine does not full sits to the top of the loader lips.
Solutions, shave off the second ledge to full seat the magazine
Load 3-4 rounds at a time and it will work without a problem. I have the same loader and I had similar problems until I reduced the amount I was loading.
Look into a product called Magguts. It increases the stock mag to 14 rounds and it's even easier to load.
Your problem is technique. Your ets will work for your sig. You just need to know the secret. Watch my short on speed loading. I am doing a review of the ets tomorrow to explain the secret. No lube needed. It helps but not needed
I'ma senior citizen and loads mags isnt ever easy. My fingers are trashed from first try with new P365. Used my Glock '
"speed loader" it is OK. could not get the 10th one in.. I think ill get this Uplula
I got the one u have 2 of . Same problem. Sending back
You jammed it when you attempted using the table top. Try again using your chest. Place the magazine in the ETS loader first. Then load your ammunition into the loader. Keep the ammunition pointed upwards and placed the magazine against your chest and push quickly and firmly on the plunger.
I have done this 1000 times or more and have never had a problem. I also know many other people who do not have a problem.
But if you load the ammunition and turn it in direction other than up before you put the plunger on it and put it on your chest the first one or two bullets jam because they’re not straight and tight against the magazine
Does sig not come with a loader? My g48 did I just assumed most manufacturers include them.
The one that came with isn't as fast for sure. But it still saves the fingers.
Ummm NO. None of mine ever came with one
@@Mo-LoveMeForever Seems like a weird place to cut costs to me lol
Operator error!!! You must put the magazine in BEFORE loading the ammo! If the mag is not seated first the bullets become mis aligned below the sight line of the loader body. If you seat the mag FIRST to the second stop not the first it works every time!! The instructions are not too clear. Alto make sure the pusher touches the body of the loader when you push it down or you won't get the last round to load. It is a wonderful gadget once you know how to use it. Also DON't slap the mag into the loader but push it. If you keep slapping it you will damage it. Push the mag in till you feel the second notch or seat. I had the same problem you did till I took some time to figure it out.
What gun is it that you have?
@@andrewcramer7214 -Gen5 Glock New York State Legal 10 round magazine oem. I use the oil as well.
So you got an ets to load a p365?
@@cameronandgunnyhigdon No I don't have a Sig P365 to try. What i do know is he put the oil in the wrong place and didn't seat the magazine properly. He should go to the ETS web site and follow their directions. I couldn't get mine to load a Glock mag until I watched the video and carefully placed the oil. Mine now works perfectly.
Good luck, Marc
Marclevy7567 , I beg to differ with you. I just received my ETS speed loader and I’m having the same exact issue and I did load the magazine into the speed loader first as far as it would go.
I tried many times even followed any and all suggestions I could find on CZcams.
This particular speed loader just doesn’t work for the P365 mags.
But I also have to say I struggled with the Glock 19 mags as well but did have success with them. P365 mags were a def fail.
Mixing oil and ammo is the fastest way to make duds. I know this from experience.
Wish I had seen this before I bought for my P365. 😩 looked like a jackass in front of my wife at the range. Oh well. It’s nothing new. 😂
It didn't work for me until I broke it in and had to push it further than I thought
WTF! Cant anyone design mags you can load by hand anymore! Like my old Berretta 92 FS. UNREAL!!!!
This happen to me too
ETS is great for regular double stacks, unfortunately the p365 is 1.5 Stack
Buy Right 1st Time What is the loader you called it and does it get easier to load the longer you use it?
Not the least bit surprised by this. I bought one, sent it back, got the replacement and just threw the damn thing away. worthless as far as I am concerned. I was hopeful, but no cigar.
I have been using an UpLula for years in my auto loaders. Bought a P365 this past weekend. While using the UpLula, I found that loading the 10th round in the 10 round clip is a real b***h. I hope the spring loosens up some. Still, I love the accuracy of the P365.
Had same issue. Over time it became easier. Not an issue anymore.
@@1MeanBone It's easier now but still a bit of a b!&*h.
Does this work with a P320 compact?
Funny, I'm having the same issue with 10 brand new Glock 33 round mags.
use chest method/horizontal for glock
The Speed Beez works best with the 365.
Great help... Many thanks!
You’re doing it wrong 😂. The first couple bullets “binded” since you didn’t turn it upside down. Plus you didn’t load the mag first. 😂😂😂
We’re you absolutely positive your mag was fully seated first. If it’s not it won’t work.
Where can I order the UpLULA?
I found you too late. I have the exact same problem and solution. I wish I had seen your video before I purchased the speed loader (mine was from TACNATION and it just sucks!).UPLula is the way to go. I have Canik's (their loader is good as well), sig P229 40 s&w and a couple of highpoint magazines, none of them would work. Only a Mossberg MC1 magazine with 5 rounds worked halfway with the speed loader.
He didn't put the magazine all the way till it snaps in place
I got a butler creek it sucks for my shield 40 and 9 I ordered the hill jack I Hurd they were better and less expensive
Minds was Stuck because I was Loading the bullets 1 by 1 on the Slide and when I try to put it in it’s was Stuck
Please help
I need help
You need to link that product for us. LOL, you could be getting commissions.
Yeeeesssss!
You also need to put the pusher into the rail. You have the pusher mounted incorrectly ! Sorry if I appear critical but you are using it wrong.
hey just wanted to let you know I had the same issue and I found my resolution. i got a .380 loader for my bersa with doublestack. after staring at it for 2 days I realized i had to dremel a good mm or two off the top edges of the entry side of my mag and now it works like magic.
I'll stick to the Magula for my P365, but I use my ETS for my double stacks.
@@buyright1sttime55 youre not using it correctly
Your supposed to put your mag in first