Making a Spherical Turning Tool - Hemingway Kits
Vložit
- čas přidán 8. 06. 2024
- Here I have a go at making the spherical turning tool from Hemmingway Kits.
Also, shoutout to @RustyInventions-wz6ir
Some of the tools I use and would recommend:
Starrett Edge Finder: amzn.to/3wLbqRp
Dykem Layout Fluid: amzn.to/3Tp2Xw1
Starrett Hacksaw Blades: amzn.to/3PdsbuW
CT-90 Cutting and Tapping Fluid: amzn.to/49TH4uo
Eclipse Scriber: amzn.to/4c6Ck6w
STA-BIL Rust and Corrosion Inhibitor: amzn.to/3wFSbIJ
Dremel 3000 Rotary Tool: amzn.to/3Pa3gIH
Trend Digital Level Box: amzn.to/49Z0dee
Sealey Imperial Hex Key Set: amzn.to/3wJFvRd
ElectroCookie Solderable Breadboard: amzn.to/4a1Dez5
Mitutoyo MIT103-129 Micrometer: amzn.to/3wDB9ei
Mitutoyo 103-130 Micrometer: amzn.to/3V4lEGr
Engineer Solder Sucker: amzn.to/438RFiT
3M Silicone Face Mask: amzn.to/3SYOLbu
Irwin Hacksaw Blades: amzn.to/3TpLOlK
Irwin Metal Hacksaw: amzn.to/3V6SvKI
Starrett 117D Centre Punch: amzn.to/3V6hRIG
Big Gator Tools V-Drill Guide: amzn.to/3Tq6hXP
Faithfull Engineers Square: amzn.to/48Jt05p
Milwaukee Set of Drill Bits: amzn.to/48O9uVo - Věda a technologie
Seems like the Hemingway kits are addictive. Nice work, Paul!
Just started this kit myself. I'm dreading that split bore and dovetails on my tiny mill! Great work.
Thanks! This kit was certainly a bit more involved than I was expecting. The split bore wasn't too bad, but the dovetails took ages on my mill.
Thanks for putting out this great video Paul. I will use it as a guide during my build. I bought a handful of their kits a couple months ago and have been enjoying working my way through them. As I was sitting down to start this build, I fired up your video and immediately discovered that my order was missing that bag of parts with the Oilite bushings and other assorted hardware. :( I reached out to them (on Friday evening (after closing hours) - and hope to hear from them tomorrow AM. If their reputation is accurate, I am sure they will take care of me.
I really wish they would use decimal units in their diagrams. I don't have them memorized, so I have to break out the calculator for every measurement. I hate to mark up these beautiful schematics with my terrible handwriting. - But, that's my Only complaint!
Many thanks! I usually take pictures of the plans, replace all of the measurements with metric, then print them out. Fair bit of work, but helps to avoid mistakes 👍
Turning a sphere is tricky AF. Anything that can help!
Amazing tool 🎉🎉
Many thanks!
Genio totaaaal...!!!!♥♥♥🙌
Excellent video, thanks.
Many thanks!
Nice work, thanks for sharing :)
Thanks!
Fantástico amigo que perfeição da gosto de assistir!!!
Boa sorte sempre!!!
Thank you very much sir. Very nice work
Thanks Rusty! No trouble at all 👍
Is there a reason you decided on using a deburring tool on that first part after reaming that first hole?
I mean, you were already set up in the lathe, why not just turn a light chamfer instead?
Good point. Didn't really put much thought into it, just wanted to break the edge 👍
Are any plans available for this ?
There are plans available, but I think you have to buy the kit to get them. If you got in touch with Hemingway Kits, they may sell them separately.
@@PaulsGarageProjects Thank you
Found it. Thank you
You mean to tell me the first test wasn't to make a metal ball to replace the plastic one that came with the kit 😅
It did cross my mind, but with the material I had on hand it would've turned out comically small!