FORGOTTEN COE Dump Truck, Will It Run and Drive?
Vložit
- čas přidán 15. 09. 2021
- Today we bring a long forgotten International Harvester Loadstar 1600 COE back to life!
MERCH! www.junkyarddigs.com/
Send us stuff!
Junkyard Digs
PO box 1623
Ames, IA, 50010
Follow the gang!
Junkyard Mook:
/ @junkyardmook
Dylan McCool:
/ @dylanmccoolvideo
Cars and Cameras:
/ carsandcameras
#international #revival #junkyarddigs - Auta a dopravní prostředky
To start comparing quotes and simplify insurance-buying, check out Policygenius: www.Policygenius.com/JunkyardDigs
is this truck a 4-speed or 5-speed on the column? I couldn't see the shift sticker on the dash very well
U graduated in 2015? I did in 2016!!!
I'm looking for a truck just like that red one to make into a motor home for travel!
You mentioned bleeding the brakes and clutch by yourself. I figured that one out a couple of years ago,fish tank airline/bubbler tubing. Walmart sells clear plastic tubing the right size to push on the bleeders and reach from the rear passenger side of my crew cab and reach all the way up to the master cylinder. I push one end on my bleeder and run the other end back into my master cylinder so that it’s submerged in fluid. I’ve also had good luck using just a few feet of the same tubing run into an extra brake fluid jug by the wheel cylinder I’m working on. Running it back to the master cylinder is a little easier for me though since I can see the air and fluid go past me and back to the master cylinder while I’m pumping the brakes. Works awesome and I can stay in the seat till all the air is gone,only have to go back and forth to go to the next wheel.
@@Bobbytrus12 2014 here!!
2:37 tip; leave both doors open when lifting the cab, it helps provide more counterbalance so the cab lifts easier
Beat me to it. Those cabs are like half the weight with doors open.
That’s a brilliant suggestion
Kevin has no time for such things
My dad had an old Ford Cabover from the same era, and it had a cab release at the back of the cab that when released allowed some assist springs to lift the cab about 1/3 the way up, making raising the cab easie,r then when returning it to its locked down position, you had to pull down on the cab to compress the assist springs and engage the locking mechanism.
@@WeChallenge You could've just had your fattest uncle sit in the cab to compress the springs.
I love the optimism of the 90 mph speedometer! Bleeding those vertical mounted clutch and brake masters is always fun.
Brakes? Bleed? Who needs those just use em as is. Tf does that even mean
I did one in my c600 can confirm they suck to bleed
Shut up wes
Brakes? Nooo, you don't need no brakes just stick your feet down and stop like Fred Flintstone! Yabba dabba doo!
Open the doors when you’re tipping a cab over cab. Puts more weight forward and lightens the cab
Look at this guy with the brain 👍🏼👍🏼👍🏼👍🏼👍🏼😎good idea literally no one knows that.
Ummmm someone said that already
@@recessional5560ummmmm you were a year late when you replied to this
Typical Junkyard Digs:
"Let's see if it runs. "
Starts engine.
"Like a champ!"
Engine dies...
Happens every time!
How much are you asking for the truck
33:37
Love watching you bring these old engines come back to life. I am in my late 60's now and can't do this anymore but it makes me smile to see young people picking up the slack keeping old things running.
Should be the 345 cid. That was their go to engine for everything!
Yes it should be
she was a tough engine could take a liken ang keep on ticken
@@busterturner8702 Could be a 304 International. The 304, 345, and 392 all had the same block. One of my cousins had a '66 International 1600 truck that had the 304. I later had a Scout II with the 304. Bulletproof engine, but really thirsty.
Yes your right. I did see the 180 hp stamped on the plate. However im still assuming.
@@rockymountainjazzfan1822 Yep, I had the same in 1975 International Travelall, great strong motor, could haul anything and climbed thru snow like a tank during winter months with spike tires on.
Always started and ran like a champ with just regular service.
Best part is you go over the causes and explain why and what needs to be done with it. Awesome, I appreciate that you share with your audience!
I was sitting there screaming "USE YOUR LEGS!!!" when you were trying to get the cab up!!! LOL I could feel the back strain from Texas!!!
I have been waiting a long time for JYD to be working on international trucks. I have a 1972 1110 pickup that I have been working on and finally got it running from your videos!
0
That's awesome dude any plans for it?
same, i've been waiting a long time, have a 1979 international scout ii
Nice I almost got my 67 international 1200 4x4 to run today
Change your toolbox password, you showed it by accident on the video haha
Thanks for going so in depth on the carb. A lot of people don't understand fuel injection, so they swap carbs on, but can't really tune those either. lol
In my humble opinion, fuel injection is way simpler than carb. But you really need to pay attention to electrical system, and that's what the majority of people is really afraid of.
There is nothing this dude can't start. I wish to be like you some day sir.
9:36
"Consistently Sad and Slow" is going to be the title of my Autobiography.
Literally the earliest I’ve ever been to a video 😂
I came early too
We all did when we were younger......
I always come early..
I'm 6days late...
@@Bran252 six days is kind of early to tell, let’s not jump to conclusions
That cabover is awesome, and that motor sounded so good even when it first fired off. What a cool truck.
Kevin...you have come a long way with your mechanic skills and diagnostic since i first watched you 3 years ago on the abandoned F250....i love your channel and all your excursions....looking forward to many more.
Hi Kevin. The International CO's were called Loadstars until about 1968 when the name was changed to Cargostar to avoid confusion with the conventional Loadstars. .
Very excited to see some internationals, currently working on a 69' 1300D and used some of your videos to help get it going!
I never tire of Kevin's Revival video's. I think it's because we are watching a man really enjoying what he is doing.
Same enthusiasm as in the Possum in the Fiat video, the one that made me discover this channel.
Hey thanks for the carburetor tips and starting your vehicle when it’s warm I always wondered why it was harder starting when I just had it running!
“But I made transoline fluid” lmfao
Making my morning coffee when the junkyard digs notification comes threw, knew it was gonna be a good day
Reminds me of my '62 step side. Sat in a neighbor's yard for 45 years. Pulled it to the house, checked the oil, sprayed the cylinders, jumped it from my van and it was running in about an hour.
That carb is probably original, and would be a stock replacement even if it isn't. If you have to time a gas IH SV-8, it times off cylinder 8, Not 1. And it uses gears instead of a chain. You can get both of those master cylinders, at about $450 apiece. The clutch slave is cheaper because it was used on light line trucks also, likely under $100. You can get rebuild kits for all of them, or be like me and use heat shrink and ingenuity. As to the engine c.i.d. there are choices, a SV-8 304 or 345, or a LV-8 401, 461, or 478. There's a bossed face behind the generator, I Think, that has the designation. They're great trucks, you'll play hell trying to kill them, if you do try, because they're made for maximum output in all quarters all day long and all night if you can keep up.
Please get this amazing man and Mook to a million😊
I can already tell this is gonna be epic. Love you guys!
Kevin I bought a reman holley ( by colt industries) and you are so right. it was 2 barrel similar to the one you have there for a Buick 3.8 even fire motor from the early 1980s. This what was wrong with it. The throttle shaft was twisted just slightly so one plate didn't close. the accelerator pump didn't work and it didn't idle because the metering block was full of white media blasting sand and the base wasn't flat. It had a tag on it and hadn't come out of the box since it left the factory. it came via a local supplier. He took the carb back and couldn't get me another one quickly. So he replaced the acc pump with the correct one took it apart and cleaned a the metering block out and fitted a better suited power valve, straightened the throttle shaft and had the base machined flat at no cost to me. That was a long time ago. Lately i've been fitting new carbs form Edelbrock . You bolt them on, attach the cable, fuel hose, the choke. you start it. It runs and idles. Check the timing, drive it for 10 minutes reset the idle and its done and no come backs for faults so far. I've fitted 5 so far and i'm happy.
I do love the look of the Loadstar and Fleetstar trucks!
Classics.
Wow those are some beautiful trucks and in amazing condition for sitting out in a field! The cab over is especially in good condition! These are the types of things id love to have in my collection.
I remember that International had a 345 Cid engine in just about everything
Usually the two barrel was it 3 45 and the four-barrel with a 392
Subscriber from the UK here.
Always amazed to see trucks of this size with petrol engines.
I guess it just shows how cheap petrol used to be over there!
@Norwindian In the UK In the mid sixties, you could buy four gallons for one pound Sterling.
The exchange rate at the time was around two dollars US, to one pound Sterling.
So US petrol was effectively half the price of the UK. Plus the fact that wages were much higher in the US.
Great job Kevin. Nice rebuild on the carburetor. Learning a lot from you.
Aw yis. fresh upload and you've got some truly tired iron to work on! Those big V8s have an amazing burble to 'em too; pretty sure the conventional one you have is the same model as Puddin's Wheelhop Wilma.
I died laughing when he yelled “Triple homicide.”
Im just watching this before work so I'll finish tonight. I had a 67 International grain truck just like the other one. Never had an issue and bought it with 21000 miles. Used as a scrapping truck since I could just dump the stuff. Great vehicle to have even today
Dude, that is an understated lovely old truck - great find! A tip on the Hayes-type split-rim, cast-centre wheels: check the torque on the rim clamping bolts. If there’s any jacking between the wheel centre to rim pads around the bolts, it’s worth stripping them down and flattening things so they fit flat and will hold torque. Reason: a friend had a European Fiat truck on similar wheels. One day he had to brake hard and the tyres gripped but the rim clamps didn’t. Both rims on the front axle rotated around the wheel centres, chopped the valve stems off and left him at the roadside with two flat tyres and a really good story 🙂
Couple of pints today eh?😉 I love this tech type videos, especially carbs which have always been a bit ‘voodoo’ to me. Thanks very much👍
Ah how I love old 60s internationals
Those are both great trucks.
I love the cab style of that conventional but I have a soft spot for COEs too.
It's amazing how smart you are. Very mechanically inclined. Lots of knowledge.
That old binder ran pretty damn good. I see you can buy intakes and cams and such for that engine, I assume it is valve float that is really limiting for them. I wonder if you did head work, how much performance you can get. Would the bottom end stand up to a few pounds of boost? Slap a blow through system with a Holley Sniper?I mean I know they are heavy as sin but wouldn't a boosted Travelette dropped with some bags be a cool Power Tour ride.
I have been around these ih engines most my life, I am told they came from the factory with a forged bottom end when they started doing that though I am not sure I know that they were doing it by the 60s though. They should hold up to 14lbs no problem
I love the idea of kevin attempting to drive with the cabin up makes me laugh slightly. It feels very junkyard digs of him
14:29 so satisfying to see how all the dirt, debris and cobwebs are blown out as she starts :D
I have a 92 f250 with the international 7.3 you did in a previous tow truck revival and I still can't kill that motor. Long as u keep oil in them they run forever and ever.
"More slippery than rust." Love it.
My brother came home with a rented moving van like that cab over to move our family a province over.
That shifter sure is weird though. The one we had had a floor shifter with a 1st "granny" gear.
I learn a lot from your instructional video's. There aren't many people around on YT that give such 'hands-on' advise. It makes me even a bit capable of doing maintenance on my 1974 Ford Mustang. Mostly because of your video's I dare to dive into the mechanics of my car.
Thanks for the detailed tutorial on the carb rebuild. It is very informative.
At 11:33, I thought it blew out fire for an instant, there... Turns out it was trans fluid. LMAO. Looked like arterial spray! Love ya, Kevin! Keep it up! -Vic
I have learned more about carburetors from watching your videos than anywhere else
Safety squints! I love it (and do it)!
That needs to be on a t-shirt
Cool.
Looks reasonably easy to work on.
I feel grateful to you for sharing your expertise with the rest of us. Thank you sir.
The Loadstar's were also built here in the UK in the 1960's, fitted with a Perkins 6-354 diesel engine.
And also in Germany (Heidelberg Plant). First with the Perkins, and then with the German IH Diesel D- 310 and D-358. I have one with the D-358. runs great!
they remind me of the old Bedfords, TKs etc.
Not sure if anyone else had mentioned this but when I open my cab overs, I open both doors. Puts weight up front to help with weight. Hope your back feels better Kevin👍🏻👍🏻👍🏻
I remember those trucks back in the day my dad's a retired Teamster and he used to drive those conventional and cabover day cabs haven't seen one of many years except those are dump trucks you have thanks for the video👍👍🇺🇸
18:29 Hm, I knew that fuel would vaporize. I think there's different conditions though. My zero turn(Kohlerr CV750) likes some choke if I start it after it was hot. I assume it vaporized some of the fuel instead of puddling in the carb like that. Probably different designs suffer from different problems (if any, depending on the model).
My briggs motors are less prone to that. The 84 dodge pickup we used to have never started hard hot, but fuel liked to drain back so it sure hated starting cold. I had a procedure that worked pretty well, two pumps and to set the choke, crank it, two pumps, usually fired off, if not I'd hold the throttle wide open. I suppose an electric Mr Gasket Autozone fuel pump would've helped in hindsight. This was back before I knew much about that engine or engines in general. My dad was not happy because (and being an aircraft, truck, and car mechanic for 60+ years) he knew it should not be that hard to start, but I guess he wasn't motivated enough to fix it. He kinda got tired of vehicles fighting him after so long. Still an electric fuel pump might've been the easy solution. In hindsight my procedure required some cranking probably because it was an engine driven fuel pump.
I haven't seen the whole video but I'm guessing that's probably a 345. Hey remember they used to have commercials back in the day where they would have the 2-ton trucks next to a scout and I think it said something along the lines of they put the big motor from the big truck in the scout. Some guessing it's probably going to be a 345 or 392
Watching the channel is hands on better than a Holley manual and you also have a good hands on tutorial for the job! Awesome, and thanks 🙏 for the video step by step repair/rebuild.
I grow up in the passenger seat of a COE, in the 1970s and early 80s big smile .good video. IH forever.
41:41 you can see the cab springs on the bottom right. Guess after 60 years they don’t have the same tension
Had to replace a
lot of them.
Was literally just wondering when JYD would put out another video!!
The cab reminds of the Bedford TK that was popular in the UK. That cab was bolted down and the only access to the engine was via lift up panels at the rear of the cab. You are lucky your working on a tilt cab, and access to the engine is easy. Cheers, Paul.
Love old trucks, these guys have just been waiting for a litlle love. They worked hard, time to give them some attention!
Ah thank you dude my leg is broke and I’m done with my school work so I’ve had nothing to do but wait on videos specially yours.
Dang o'l busted my bucker man
That cab over would make one heck of a baller car hauler
Yeah, but it'd be super uncomfortable, noisy, and tiring over longer trips. The Roadkill guys have it figured out with their squarebodies with A/C and overdrive units.
@@keon5779 Easily cured with a Vintage Air ac system and an engine and trans swap
@@ae86hachi That's not going to fix the harsh ride and cabin noise that results from the design of a cabover.
I just love these old trucks and what ya all are doing with them to get them on the road again! Keep the good work up and keep these vids coming! Merry Christmas from sweden
I looked these up. They used the 304, 345, 392. I would say it is a 345. I like these trucks. My uncle had one on the farm. I believe it was a 1970 model. He also drove a 1970 International 1110 pickup. According to family legend, he bought both of em at one time to replace the older Ford Grain truck and the old Studebaker pickup. Awesome video. ❤
I've had several of both along with Chevys and Ford's.. The IHs were the most reliable..
The handling reminds me of a Ford's and I love that
when you use a stick for the throttle when the linkage is right beside your hand :D
Great video glad you posted keep them coming thanks
My dad had the same truck ❤️ I drove all over the country That truck has a column shift Love it put her back on the road
Hell yeah a loadstar
Kevin uploading on a Thursday????? Honestly today felt like a Friday lol
Its eh
It's not the same day for everyone
Outstanding!
I appreciate the class Professor! 🎓
Excellent work Sir. 👌
304 was their base engine. Optional 345 or 392. Had a 75 3/4 ton pickup with a 392
A guy might need a lone wolf 2000 love the content keep it up
grew up with an old COE (cargo-star) IH ours had a 345 gas engine with a 5 speed column shift, the 2sp rear end was a toggle switch on the dash.... loved that old girl
I had one of those. Stick on the floor. Flat bed. The cab over had coil springs to keep it up and help to lift it! It was a great truck. 390.
Kevin you killed me with battery,"It's consistently sad and slow comment", you nailed the way it sounds in this motor
Like when I had my battery in the car tested as was not a happy starting diesel and the tech goes "Oooh she not happy. " what was funnier was he was talking to himself lol
Oh man, I love the sound of that starter when you are cranking it!
Kevin said he struggles getting it up, he played with it once before to no luck. HEHEHEHEHEHEHEHEHE!
Glad to see I'm not the only one who picked up on that 🤣
If you want to learn about IH's watch Hodge Podge Dodge Garage.. despite the name Zane is an IH freak, he's only got like 6 including hid dad's old 1968 Travelette and a couple wreckers. Plus he's just a good guy.
as Kevin goes for the weightlifting record in revivals in this one.
he looks like a strong dude, that cab musta been heavy
Ah yes, good ol’ transoline oil. Also this is not the first international engine you’ve worked on. I’ve done some googling and the Ford IDI’s were originally international Diesel engines
International made all their diesels beside the current 6.7l
That would be navistar international not really IH anymore
Basically the 6.9/7.3 idi & 7.3 PSD are the only good ford used dsls that are any good.
6.0 & 6.4 are trash. Idk abt power.
@@HALOman-vi2tg oh ok
I had a ‘76 Ford 6.9 diesel, that thing went 225,000 for me, I sold it to a friend and he got another 200,000 out of it! The body rusted out but that engine was still going.
man you make good revival videos on classic, modern, and rare weird vehicles... It really helps a lot with learning about engines and vehicles and stuff!
My first visit really enjoy watching thank you for your videos
No offence, but Jed looks like a Scottish Santa. That beard terrifies me
Like I told you when we met in Norwalk, I love that your channel inspires the "average hooligan" to not be afraid to work on sh** and enjoy it!!! When I did the revival of the "Intercamino" on my channel, it had a carb nearly identical to this on the 345 and we had a leaky accelerator pump (which I replaced) and gaggle of other issues that made it run like poo... I wish I had seen this video before then cause I'm literally watching this thinking, "Damn I coulda rebuilt that carb and had way more fun with my monster truck El Camino on an International truck chassis if I could have made it run better!" 😂 It worked-ish and is still working as a temporary carb for my 68 GMC revival so it is what it is... Moral of the story is you just continue to inspire! Check out the channel if you get a chance and as always thank you for the awesome content and inspiration! 🤘🤘🤘
My friend used to own a 1960 IH BC 180 Tandem Axle Dump truck i got to ride in it. 20 speed twin stick. the tandem dump truck had no brakes & every gear would grind when my friend would drive it. we were hauling dirt with it & we backed it to far down a small hill & it got stuck but friend drove it out LOL! it had a original battery that died so the truck got towed away for scrap.
Nice job Kevin. Your explanations were thorough and easy to understand. It just bothers me that this old rig won't be moving any time soon.
Im always happy when Kevin is working with one of the greatest farm trucks!
I graduated in 95. I feel old.
I was suppose to graduate in 86.. think ya feel old now?
Old lol I graduated in 76
At 17 min. Brilliant dude! My son wants to be an engineer and will show him this as an exemplar on how to work a problem. Cheers from Smithers bc
i love that cab over. so cool
Id swap in an 8v71in the cabover
I’m remember driving one of these when it was new. The column shifter was a challenge when new but after the truck had more kms the gear change was like pin the tail on the donkey. This motor should be a 392 but it’s a lighter duty truck so it might be a 345.
I’m not saying it was a fantastic engine but at the time GMC was selling offering a V6 and Chevy’s small block was limited on power. Ford offered a decent truck/motor and so did Dodge but IH had a long reputation of building trucks and the 345/392 was kind of a small/big block.
FYI International has made a 4 cylinder that was half of a 304. The distributor app was virtually the same but 4 posts were blocked off. It was actually a very reliable motor. I had a Scout with one.
I enjoyed the heck out of this. Thanks!
You did good good on the carburetor,explained everything in detail, the motor sounds good for stating that long
Hey call kunau implement in preston Iowa and I bet you that they can help you out with getting any parts that you need for any binder adventurers you end up going on