How to Install Rake/Gable Trim: ABC SL-16® Metal Roofing System
Vložit
- čas přidán 11. 08. 2014
- Our host David Mackey discusses techniques used in installing Rake and Gable Trim using the SL-16 standing seam roofing system from American Building Components. Visit our site to learn more and view our products: www.abcmetalroofing.com/Products/
- Jak na to + styl
Awesome, simple style - I like it!
Excellent Video
Super great. Just what I needed. Thanks!
I see that your recommendation to fold down "1 1/2 Inch tabs" at the eaves would have fully covered the hole. You marked and cut a 1" tab, which is a little short. Over-all, nice job.
I can't find any videos on T-Style drip folding for Hip roof corners.
I'm building a shed against the back of a house. I'll have a hi-side trim installed on the side of the house and extending several inches over the shed roof (extending over the panel ribs and installed on zee-closure). I'll also have a rake trim installed on a perimeter cleat and zee-closure. How do I finish the rake trim where it meets the hi-side trim?
Does anyone know how a metal panel (exposed fasteners) installation on a Roof whose Ridge is longer then the Bottom. Should ridges be cut just before the Rake edge or should Ridges be tucked under Rake with the rake cut. Installer cut the Rake and tucked Ridges under Rake. Now water runs under metal.
Why would you have to use rivets when using the z bar though ? Is only one end of the rake hemmed ? Because the rake I install has a hem and kick on both sides and snaps together like ridge cap
5:12 he looked like, wait am I getting ahead of myself.
Excellent instruction.
How about rake on a gambrel roof no one seems to cover this
Did you ever find an answer Dave? I have a metal roof on my house that is leaking at all 4 corners, I think it is because the trim sits on top of the high ridges of the metal, then there are large gaps in the valleys of the metal all the way down.
Electric chair. Lethal Injection. Hanging. Firing Squad. This video.
Which would you choose?
Do I get a cigarette with the firing squad?
Where do i find those arm protesters?
Why do you need to seal it with that special tape when it’s just going on top of the roof that’s already metal?
You didn't show anything about the cutting and bending?
Does rake trime goes all around the roof or only on the sides?
Only on the rake. Not on the eave. On the wave the water just rolls off the roof.
nice gloves and arm protection
Hey let me get my little level square out when I'm 40' in the air on a 9 pitch You better be able to pull it together and cut that on the ground
Picky detail; I don't like how the final fold is the fascia side. The final fold imo should be the top flap. 2:51
I didn't like he's first cut
supppose gable is tapered.any solution or you will give the gutter
Hi Hamza; thanks for your question! To accommodate a tapered gable design, you can order tapered rake trim.
***** no we cannot use ! i feel you dint get my question ,suppose our eave length is different for both side.so Automatically gabel will not make 90 degree with eave.so in this situation you need to give path for water exit .how you will handel this situation.
Hi Hanza. What you're describing sounds like when your rake comes into your eave, it isn't at 90 degrees. Despite this, you would still install your eave trim underneath the roof panel and install the rake trim as shown in the video. This will require that you modify the angle for the rake trim to suit your field conditions. If you have any further questions about your specific project, one of our representatives would be happy to take a look at your drawings to better help with your specific field conditions. You can find a representative in your area here: www.abcmetalroofing.com/About-Us/Locations/.
What is the purposenof the continous cleat?
It's a clip so you don't have to screw through the finished cover trim. Prevents the bottom from lifting off in winds etc
Yano if i had a video like this about 35yrs ago that would have been awesome?!? LOL I grew up in a time they didnt even have cell phones so i ,surely didnt have youtube! lol I have done metal work and facia and trim for years. A lot of that can be incorperated in the installing of the metal roofing. But when it comes to the type of products you should have too install it is the thing? I just need to know what items and products i need to get a roof done? Like starters ,which you are calling a continuous kleet. But its basically a metal starter strip, channel lock for the last piece....? In any case i just told a guy that is hiring me yet a 3rd time to do some work i could install the metal roofing like i have done it before.......nope! LOL but i am 100% sure i can figure it out! Now i know there are things i dont know about it i should know. But then i wouldnt be working so.....hehehe Where can i go to find out what products i need for this type of roofing? So im not totally winging it?lol
You just skipped filming the important and probably difficult part finishing the eave end. Why?
interesting accent , American/Canadian / Irish mix ?
Whats the purposenof the Z trim?
To stop water and attach gable and ridge caps
My goodness---- sharpen that pencil
So if I follow your recommendations with the double-sided tape I will never pull that trim back off to be able to fold the end like you want for the eaves. So I guess unlike you I will manufacture the piece first then put my tape on then install it. 😜
This was not written for the novice in mind. I consider myself a capable DIYer; but, there was MUCH that I didn’t understand with this video and he cut out a lot of details that could have otherwise been helpful.
@JohnnyRingo not at all.
I see you're using Wiss brand seamers. Don Wiss is a piece of crap and tried to have me fired from a pizza shop call center I worked in 25 years ago.
To long to boring can you talk any slower
playgirl, go play somewhere else!
Get-The-Lead-Out.45 exactly I have a metal roof to put on
You can slow down the playback speed if he gets ahead of you. :)
For the love of God, if you are going to insult someone in writing, please learn the difference between "to" and "too"... sheesh...