200 Series Landcruiser Drawer Install: How to install ARB Mid Height Roller Drawers into a LC200

A detailed look at how to install the ARB outback solutions mid height roller drawer system into a 200 series Landcruiser.
Install requires:
Two (2) RFH1045 Mid height roller drawers or selected 1045mm drawer combination
ARB wing fitting kit for an LC200
links:
www.arb.com.au...
www.arb.com.au...
www.arb.com.au...
Contact us: [e-mail]
Disclaimer: The information contained herein should NOT be used as a substitute for the advice of an appropriately qualified and licensed professional. The information provided here is for information and demonstration purposes only. Please seek additional information and advice before attempting any installation. Border Touring take no responsibility for the use of their material for any installation of any product.

[@sethferwerda628]

Just come across your channel mate, I like the way you go about it :)

[@raysater4083]

Basically a very helpful vlog, basically I will buy a set.
Thanks for basically doing this your basically awesome.😁

[@harryd6528]

Great video. Very useful.👌

[@MADTAS4]

Thanks for the vid, ordering a set for my Fortuner. Congrats on the bub 👍

[@gibogobshite]

Brilliant saved me a headache or two 👌👏🤙👍

[@BTN1979]

Thanks for video. Was really helpful. Could you link the tie down you used for the fridge at the end? Cheers,

[@bordertouring3265]

www.arb.com.au/camping-touring-accessories/tie-downs-cargo-straps/#snippet-107103

[@1boofy]

Hey mate,
With the spacers, plates, bolts etc did these come with the 200 series fitting kit- or did you need to use only the components in the standard fitting kit that came with the draws themself
Thanks

[@bordertouring3265]

From memory it was from the standard kit. The 200 series kit only included the wings.

[@Go2ISU]

Any idea if one drawer would allow for one half of the third row seat to still fold up and remain functional? I need one seat to still be useable, three kids.

[@bordertouring3265]

I've seen photos of this being done. Your ARB dealer will confirm though. Check out the 200 series Facebook page I'm sure I've seen one with just one side of the drawers in and the chairs down.

[@garrydietrich9786]

Great Help, thanks. Is there any mod required for the rear air con vent on the left side of the drawers?

[@bordertouring3265]

Garry, I didn't have to modify anything but depending on your model there is a bracket work around and instructions in the kit

[@offroad_md]

Hi,
Can you let me know if the parts used in this video are RFH1045 (2) and 200FK? Anything else used?

[@bordertouring3265]

Sandu, that's it. Each draw comes with a fitting kit and so too does the wing kit.
They end up giving you much more than you actually need so you will have spares.

[@offroad_md]

@@bordertouring3265 thank you for detailed reply

[@offroad_md]

@@bordertouring3265, hi again,
could you please advise wherever you also used RFFKADP1045L & RFFKADP1045R?

[@bordertouring3265]

Sandu, I am not sure. The code sounds like a left and right wing kit but I'm not familiar with it. I used both left and right wings in my install so make sure you have both.

[@andrewarthur4657]

How are these draws holding up

[@bordertouring3265]

Still working well. We don't require a pram as much anymore so likely to swap out and have one low and one high draw in the future. Possibly the kitchen version if they do a wagon version.

[@coleEmmm96]

Basically

[@heathstokes247]

Basically?

[@tierandonnelly1420]

hey mate. what did that set of draws cost. thanks

[@bordertouring3265]

Just under $2000. They also wanted $600 to fit so it was a no brainer to fit myself. Quality is the key here for the price. You can go cheaper but they are terrible quality or you can go more expensive and fully customise what you want. I took the most practical route with a new bub and stroller.

[@tierandonnelly1420]

Thanks for getting back to me so quick, arb aren't even that quick at replying haha. I have the same colour 200 and are slowly doing similar mods to what you've done. when's the next vid coming out? I really enjoy your content.

[@bordertouring3265]

Cheers mate, I have a few filmed ATM just need time to edit them. Redarc tow pro install, Merimbula travel vlog, tailgate dampener install, etc.
We have an 8 month old at home so it does get hard to get to them. Thank for the kind words, I'll keep at it and we hope you have fun with your 200 build.

[@tierandonnelly1420]

that exciting news. looking forward to seeing your vlog of merimbula and the tailgate dampener is defiantly something iv wondered. thanks mate

[@mikefrisbee960]

@@bordertouring3265 do you have the part numbers you used? Thanks