How to Replace Harmonic Balancer 96-99 GMC K1500
Vložit
- čas přidán 4. 07. 2024
- For More Info visit us at: 1aau.to/h/UE/
1A Auto shows you how to repair, install, fix, change or replace a worn or uneven harmonic balancer. The video is applicable to the 96, 97, 98, 99 GMC K1500 V8 5.7L
This process should be similar on the following vehicles:
1988 GMC K1500 Truck
1989 GMC K1500 Truck
1990 GMC K1500 Truck
1991 GMC K1500 Truck
1992 GMC K1500 Truck
1993 GMC K1500 Truck
1994 GMC K1500 Truck
1995 GMC K1500 Truck
1996 GMC K1500 Truck
1997 GMC K1500 Truck
1998 GMC K1500 Truck
1999 GMC K1500 Truck
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oD9/1AXAA00013
• Complete Metric Socket Set 1aau.to/oop/1AXAA00043
• Adjustable Wrench
• 3/8 Inch Air Impact Gun
• 3/8 Inch Drive Ratchet 1aau.to/oD9/1AXAA00015
• Socket Extensions 1aau.to/oD9/1AXAA00015
• Torque Wrench 1aau.to/otm/1AXAA00044
• Hammer 1aau.to/oiK/1AXAA00091
Subscribe: / @1aauto
Check out our playlist:
GMC Sierra K1500 1988-1998: • GMC Sierra K1500 1988-...
For More Info visit us at 1aau.to/h/UE/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Auta a dopravní prostředky
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Good video! I just finished the same job on my1995 V6 Sierra, except that I did it from underneath on a creeper (I'm 72 with a bad back so I prefer not bending over the truck).
When he says use the appropriate size wrench then grabs a crescent wrench lmfao .. good work easy money great video and info for learners A1
+jackinhard Thanks for checking us out! 1AAuto.com
Just wondering if it is possible to put a mark on the inside lower half harmonic balancer so if rubber decays and loses the mark original Mark can be determined and marked with paint
Hi and thnks for all informative and helpful videos.
I have a ford mondeo mk4 2.0tdci and I need to replace the crankshaft pulley.
But the car is with automatic gearbox and iam wondering if there anyway to remove the pulley with out blocking the flywheel.
Iam thankful 🙏 for the help.
2
Glad i watched this ..excellent repair video as always... so happy i do not need to remove water which i installed last month...thax
+roadstar499 Thank you for the feedback!
I didn’t see the timing mark on the old one lined up with the mark on the block. When you installed the new one it was on the timing mark. Is it possible to not have it timed right?
Do you sell the harmonic balancer installation tool for 6.2ltr v8 diesel engine
Some vehicles have red Loctite on the built pully mounted on the harmonic balancer. You will need to 400F heat to break it loose
I don't know the temperature rating of the rubber
Also possible to mark line of paint down in front and over balancer factory timing mark.. to see if balancer is moving. line would begin to stagger..
is there not a seal behind there too. probally be a good idea swap if your right there i am.
Cool that’s gonna help me out a lot
Thanks!
Do you have to put the balancer on timing marks before removal ?
+Pedro Collazo Thanks for watching! You do not have to make timing marks when removing and replacing the balancer. 1aauto.com
How can you tell when it’s been seated all the way ?
You dont need to put some silicone inside the harmonic balencer?
Cody Houston likes this
Do not hit your harmonic balancer with a hammer! Use a harmonic balancer installation tool!
+GoldenTV3 Thank you for the useful tip! 1aauto.com
What do I do if the the first part of the installer won't come out
I ended up having to re install the bolt and torquing it down until I could back it out. I would recommend not tightening the first part and have it finger tight(as the instructions would recommend). I don't know why he even used pliers to be honest. Some of these puller kits also have a socket end which would much easier.
Where is the tool number for installing the BALANCE SHAFT?
What de number of thé tool you have use for install crankshaft balancer ????
+dinelle69 Thanks for checking us out! You can find a list of the tools needed for this installation in the description of this video. Hope this helps you out!
In the liste no have put number tool install the harmonic balancer just screw driver sucket....
No mention of the key. If you don't line up the key with the keyway it will never go on!😒
+Car Wash Adam Cooper Thanks for the feedback!
that belt though