Building my DIY robot dog - SpotMicro
Vložit
- čas přidán 15. 06. 2024
- This is an assembly video where I'm building my first DIY robot dog, a SpotMicro. It is an open source project based on Boston Dynamic's Spot. This video takes you through the full process of building this 3D printed robot dog.
SpotMicro: spotmicroai.readthedocs.io/en...
STLs: www.thingiverse.com/thing:344...
SpotMicro V2 STLs: www.printables.com/model/1450...
Chapters:
0:00 Introduction
0:39 Parts
1:02 Servos
1:55 Leg Assembly
6:07 Chassis Assembly
10:13 Electronics
11:57 Closing Case
13:10 Finished - Věda a technologie
Cool. Yeah Chris Locke built this and decided to elongate the torso because it is too short
I might consider that too. I managed to find a smaller battery that fits, but the electronics are still squeezed in pretty tight.
I did, yes... thanks for the mention! but I skipped the Pi, preferring to cobble together lots of arduino hardware instead.
I triple dog dare you to release your code (ik you said you wanted to clean it up but yours is the best and simplistic I’ve seen)
My code has been my most requested release. I'm definitely making it a priority and I obviously can't pass on a triple dog dare.
@dado_offbrand9499 I've finally released my code: github.com/AdvancedHobbyLab/SpotMicro. Let me know what you think.
@@AdvancedHobbyLab I am planning to build mine this week! I still have a lot of supports to remove and clean but I’ll keep you posted!
Sounds great! I look forward to seeing what you do.
I need confirm one thing. While assembling all your servos are set at zero right? Do you set the min and max limits for the servo in program right? I asked because for the shoulder it need to not be set at zero while assembly but 90 degrees. How do tackles this program? Cause if you don't they legs will break upon sweeping it the full 180 degrees the way you've assembled it. Also what program I need to run in the repo to make it walk? and Also I just have PCA9685 and RaspberryPi. What changes do I need to make? Thank you!
By zero, I mean 90 degrees. It is about your frame of reference. Servos have a 180 degree arc which can be viewed as 0-180 or -90-0-90. In the latter, 0 would be equivalent to setting the servo to 90 degrees. You can use a different angle as your 0 position, but the joints will need to be mounted according.
The min and max limit are set in the program. I currently don't have any programs in the repo to control the robot, however, you can look at "locomotion_test.py" to see how to make the robot move. I still need to work on a video for how to control the robot.
The servo hat that I am using also uses the PCA9685 chip. It should work, however, I found that it struggled to carry enough current to the servos. I had to solder some extra wires from the power terminal to the servos to bypass the small trace wires on the PCB. Hope this helps.
Cool . What is your opinion about official language to program robot dog in the future ? C sharp ? Python? thank you
Good question! I'm a big fan of Python. For this project, I used jupyter-lab and set it to be launched when SpotMicro boots up. This allows me to edit and run the code from a web browser which made development very easy.
@@AdvancedHobbyLab Python is the best for people middle level but it is slow language . You can see the market . My opinion
You're right. Python is a slow language. I'm just using Python for its convenience. What I've seen people do in the past is use Python to develop their algorithms then transcribe them into a faster language such as C++. That way you get the best of both languages.
I take it that you're a C sharp developer? Have you ever programmed robots using C sharp? What was your experience like?
@@AdvancedHobbyLab no I m not developer . I studied Python beginner but I m suggested to study c sharp for future . I m mechanical designer , i like apr and robot dog
Hello, what battery you use and how you deliver enough current to all servo ?
Any 2S lipo will work. I use a 2200mAh battery so that it will be small enough to fit inside the chassis. I decided to use: amzn.to/3WTydp2 (Affiliate link)
I bought servos that can run at 7.4V so I could just route the battery power directly to the servo controller. My servo controller had a MOSFET in the circuit that couldn't handle the 7.4V. I had to solder on some extra wires to circumvent the MOSFET and directly connect the input voltage to the servos.
Hello, interesting work, had you published the code?
Thank for the support!
You can find the GitHub repo: github.com/AdvancedHobbyLab/SpotMicro/tree/main
How much to but one robot dog costing? US$1000?
It cost me maybe US $250. The biggest cost was the servos. I already had my own 3D printer so making the parts was cheap.
Brothee its cool but where is code of arduino
I'm glad you like it, however, I have no plans to use an arduino. You can find the github repo here: github.com/AdvancedHobbyLab/SpotMicro/tree/main. The code is written in Python, but perhaps it could help you with arduino code.
deaminations of leg