Video není dostupné.
Omlouváme se.
How to install Yamaha Star Bolt Tall Handlebars, Extended Throttle/Clutch/Brake Lines, and Grips
Vložit
- čas přidán 3. 09. 2014
- Avon Grips:
www.chapmoto.c...
www.chapmoto.c...
www.chapmoto.c...
www.chapmoto.c...
www.chapmoto.c...
Currently in the middle of doing all of this, can't tell you how helpful this video is.
Glad to hear you found it useful. Ride safe.
Where did you find the bars? I've been looking for them but they are no longer carried everywhere I've looked.
Thanks for the video. I'll be referencing this when I install next week. I had a hell of a time tracking these bars down (in IL). I couldn't find them in stock online so I called about six dealerships until I located one set in Missouri. Most dealers showed a backorder status and they had no idea if they would be getting any back in stock. I think these bars look far better than the alternative Baron mini apes, so if you're interested in these you better get hunting.
Thanks for watching.
What are these bars called?
Fun fact, you can use the stock cables from the Yamaha V-Star 950, they are 6 inches longer than the bolt cables but everything else is the same.
Thanks for the tip.
@@chaparralmotorsports Glad I could help.
Absolutely love your videos!! will you guys ever post videos on the Bolt C-spec handlebar rising? the C-spec has clip-on bars and I'm pretty sure do not have the same type of cables as R-spec.
did you ever figure this out?
+Manuel M No problem at all, we're happy the video was helpful to you! The kit doesn't specify what size washer it is. The inside diameter of the washer however is 14mm. What you can do is take the rubber damper off and see if you can match up the circumference. I hope this helps you out!
this is a great video. Thank you very much. Where can I purchase the braided extended cables?
Hi Touraj, thanks for watching and commenting. We sell the extended cables. Here is a link to the throttle cables: www.chaparral-racing.com/product/yamaha-extended-throttle-cable/1tp-f63b0-t0-00.aspx
here is the brake cable: www.chaparral-racing.com/product/yamaha-extended-front-brake-line/1tp-f58e0-t0-00.aspx
here is the clutch cable: www.chaparral-racing.com/product/yamaha-extended-clutch-cable/1tp-f63a0-t0-00.aspx
Thank you very much.
I am in the Bay Area. I sure wish I could bring my bike down there and have you all change the handlebars for me. I have couple of weeks off in November, I might ride it down and have you guys do the work on it. Thanks again.
OK Touraj, sounds good. Best to check with our service department ahead of time and make sure they can get you in. Here is the number: 1-909-889-2761
Excellent video guys, didn't leave much to the imagination at all.
where can I order those steel washers ?? that replace the rubber dampers . . .
Hello, i’ve got another question. I live in Holland where most bikes have ABS. I read on forums that it is impossible to change bars on the Bolt with ABS as you can not make that cable longer. But i went to my local dealer here and he Said that the ABS cable has got nothing to do with the handlebar as it only Goes from the brake-disc to the engine..(so not to your brake-lever). Is this true? Or did he gave me the wrong info. I want these tall bars so badly, but i’m afraid i can’t change the bars.. thanks in advance!
You can totally swap the bars on an ABS bike! Your local dealer is correct in the fact that the ABS line does not go up to the handlebar. Every line and cable up on the handlebars can be extended. Thanks for watching. - Kyle & the Chap Moto Team
@@chaparralmotorsports Thank you so much, really needed that answer haha! Thank you for the reply!
@@jellevanbeers2793 No problemo!
Why we can't put this handlebar on bolt with ABS?
Yeaaaa, think ill just pay someone to do it.
Ha! Sometimes that is easiest and most effective for your AND your machine... Wink Wink !
Yea 💯 % damn man that seemed so difficult just to change out the Handel Bars 🥵 I'm buying a BOLT and he has some weird short handlebars on it , and the guy was like yeah it's pretty easy if you want to switch your handlebars , Now after watching this video I don't know if I even want to buy the motorcycle 😬
@@surplusbuyerliquidator934 lol dont let that stop you!!!
hm would it cost to ship these to the philippines.
Bad ass video man..thanks. I will be in your shop soon to visit...
Would also like forward controls if you know where to get them from . Thanks for the videos !! Keep them coming
Hello Leslie, thanks for the kind words. You would probably be looking for the Yamaha Rider Foot Peg Relocation Kit, unfortunately we do not have that kit on our website and I am not sure if they are available from Yamaha anymore. You'd have to so a search for them. Sorry.
hi i watched the whole video but I am still looking for answers. i have a bolt but my bike came the clip ons right on the forks looking to swap out. riding after a while my lower back is on fire. what's the easiest way to swap out and top mounted bars
Hello, take a look t this forum thread, it may help. www.yamahastarbolt.com/how-to's/c-spec-handlebar-conversion-no-extensions-required/
I'm trying to find the measurements or a link for just the steel washers to replace the rubber dampeners; I'm installing after market custom bars and they don't come with any obviously. you guys able to help me out with that?
Hello, sorry it has been many years since we shot this video, we do not recall.
awesome video guys. I have a question for you. I bought the handle bars used and wasn't aware that they came with steel washers which of course, the guy who sold them to me didn't include them. Can you tell me what size the washers are to I purchase them from a third party? thanks
For the connector on the throttle side it’s very difficult to remove. Can you advise if the plug should be squeezed on the connector or pulled?
Thank you for watching Donie. Either strategy can work, it just depends on which side of the connector you want to work from. On one side, you will depress the inside to move the little barb downward. Or you can use a small flat blade screwdriver to gently lift the tab on the top. Your choice. - Kyle & the Chap Moto Team
Appreciate the response and I managed to remove by wiggling the connector out. One last question. The bar appears to be a little larger that stock. Is that normal? the clutch perch is peeling the paint off the bar as I try and slide the perch on. Any suggestions?
No problem Donie, that is what we are here for. The Perch can be loosened and if you put a flat blade screwdriver in the slot and wiggle it a bit, you can "open the clamp a bit." When you tighten the screw it will all go back into its original position. It's not that the bar is bigger, it is the powder coat all the way around the bar that increased the outside diameter. Thanks for watching! - Kyle & the Chap Moto Team
Just an update. Tried prying the gap to no avail. Sanded down the bar with a light sandpaper and sanded the inside of the perch and its now on. Thanks again for the help!
Nice work Donie! Great work! - Kyle
ok, since the handlebar you mount in the video does not produce it anymore, please recommend a handlebar you know as an alternative
Hello, there are other options available, it will be based on your style and what your want/need. Please check the Bolt forums for ideas.
You guys in SoCal? Do you have installation options on parts purchased at your store? I dont have the experience or tools for this add on.
What's the size/diameter of the hole in the triple tree that the handlebar bolts go through??
So my Yamaha fairing will fit with these bars?! I’m really hoping.
Hello, if its the Yamaha mini fairing it will fit.
Would these bars work on a 2018 bolt R spec? If so how long would it take to install them on it if I ride down to ur shop?
Yeah they should work. You'd have to talk to our service department about install times. You can reach them by calling (909) 889-2761 x 120. The service department is open Tuesday-Saturday 10am-6pm.
After you change the dampers what torque specs for tight back the bolts?
Hello, sorry it has been so long since we shot this video we do not recall. Refer to your owners manual for handlebar torque specs.
Hey guys, thanks for the detailed video! One thing I am misunderstanding here. On the lower part of the risers I am not able to take out any rubber bushing. It's hard to see but I don't think I see one. Is there one on the bottom side? If I install the lower riser washer it will not sit flush with the top triple tree. Thanks!
+KingOfLuck Hi thanks for watching. You only need to remove the rubber dampners that sit beneath the washers on the top side of the triple clamp. There are no bushing on the underside to remove. Just remove the dampners, put the included washers in their place, install the risers and and bolts, then slide the other set of included washers in place from the underside.
well worth the effort good job!
Thanks!
Hey guys, I would like to find out what parts you used on this bolt , my son has a 2019 and I can’t find anything . Wire extensions , cables nothing. To make it worse I’m in Alaska and we can’t just go down the road and have some made . Can you help
Hello Leslie,
Just below the name of our CZcams Channel are all the links for the products we used. If you still need help, give our customer service department a call (800) 841-2960. Thank
I have the tall handle bars (bought bike used and they were on bike) and want to add two more inches of rise. I bought the risers and realized I do not think the cables are long enough. Will I need extensions to add the risers.
Hello, without seeing your setup we can't say for sure, but from what you're describing it sounds like yes you will need longer throttle cables and brake line.
Where can i find these bars? They're out of stock on your site :(
Hello, sorry but I am not sure.
What is the right length for the extended cables?
Hello, when going with the Yamaha cables, they don't list length, they just call them extended length cables for their tall handlebars.
i got a 2022 bolt and bought the bitwell frisco set with a 7" rise do you think i will be fine with just the extended cables or is there wiring extensions i will need ??
Hello, those bars will have the switch housings sitting about 2" taller than on theses Yamaha Bolt Tall Bars. We've never installed the Frisco bars on the Bolt so we cannot say for sure or not that just by rerouting the switch wiring there will be enough slack to turn the bars left to right/stop to stop. You can try test fitting them, but yo may need to extend the wires.
I ask you for advice please, I have this same bike, yamaha XV950R,
I am undecided whether to mount an 8-inch ape hanger like this one you mount in the video or a 12-inch one.
I'm 178cm tall
You who know the bike well what do you recommend?
I don't want the hands to go beyond the shoulders
a thousand thanks
Maximilian
Hello, it's difficult to say because every body is different. Two people of the same height may have longer or shorter torsos or longer or shorter arm reach. So 12" apes may not be suitable or comfortable for two people of the same height. Also it may be dependent on the laws/regulations of your area. Some places state that the handlebars cannot be above shoulder height. Probably test fit a set of 8" bars to see if they are safe/comfortable and if you would prefer to go up to 12" bars.
What bars are those ? I really like them.
Aaron Leblanc Those are Yamaha's Star Accessories Tall handle bars
hello thank you, but unfortunately today they told me that yamaha no longer produces this handlebar 😞
As an alternative I can take baron
BA-7350-08B HANDLEBAR SKINNY APE 8 '
What do you think?
We haven't tried the Baron bars with these so we cannot say. Sorry.
Hi, great job 👏👏👏 . I have a question: if i change factory handlebar on my Yamaha Bolt to 8 inch handlebar, have i need to change Gas/Clutch/Brake cables and electric cables? Or second question how many inches handlebar can install without changing any cables? Thanks alot
Hello, it's been a while since we shot this video but they were about 8" tall. Yes you will need to change your cables and clutch/brake lines.
@@chaparralmotorsports thanks ✌️✌️✌️
Where is the link for the Handle Bar?
Hello, here is the link for the tall handlebars. www.chapmoto.com/yamaha-tall-handlebars.html
Thanks so much for this video
Glad it was helpful!
How much is the cost to install the bars very interested
Hello, please contact our Service Department for install/labor rates. (909) 889-2761. Thank you
Thank for the video I loved those handle bars can you please tell me what brand or where can I get them ? Thank you
Hello, they are the Yamaha Accessories Handlebars. We sell them on our website: www.chapmoto.com/yamaha-oem-handlebars-1tp-f61b0-v0-00
Hello, is this bar fit for yamaha xv950r ABS latest version 2017-2020?
Thank you
Maximilian
Hello, yes.
hello thank you, but unfortunately today they told me that yamaha no longer produces this handlebar 😞
as an alternative I can take baron
BA-7350-08B HANDLEBAR SKINNY APE 8 '
What do you think?
Hi..Do you have a part number for those grips?
Thank you for your inquiry Donie. Yes Sir! The Avon Grips used can be found here: www.chapmoto.com/avon-grips-custom-contour-grips-parent-317-9253 - Kyle & the Chap Moto Team
great video. I just ordered some 10' window bars. wondering if I can go with the star cable extensions or would I have to use the Barron ones. ?? please help . and how much for the star cable kit ...thanks.
Hi Antwon, thanks for watching. I' don't have any experience with 10" bars and the Star extended cables. Off the top of my head I'd say the Star cables probably won't fit seeing as how they are designed for the Star Tall Handlebars which are only about 5" tall. So you may need to look at the Baron's cables or I believe Motion Pro has some too (depending on the end rise of your bars you might be looking at cables that are in the neighborhood of 4-6" over stock). Maybe check with the shop you bought the bars from and see if they have any experience with the 10" windows/Bolt setup and see what they say. BTW, just a heads up, if you're running 10" bars you may find you need to extend the electrical connections as well. Hope that helps.
Thanks for the info brotha. U guys rockkkkk
Do you know if they still sell them ?
Not sure, you may have to search around for them. We no longer have them.
How long should a project like this take to complete? I'm not mechanically inclined so if I take it to the dealer I want to make sure their not charging me all day for a 2 hour job.
+Daniel Mulligan it's a pretty straight forward swap, although there are several tasks involved. At the dealer it's probably like a 2-3 hour job, it depends on the service tech the performs the job. Whoever you take it to ask them to give you an estimate first.
Love your vids! I Got One question, are those bars 1 inch bars? And do they fit the stock risers? Because the stock bar on the bolt is 7/8 inch right? Or am I completely wrong?... I am looking for an 1 inch bar, But i’m Worried I need to buy 1 inch risers too!
Hi Jelle, the stock bars on the bolt are 1" in diameter. These Yamaha Tall bars are 1" as well so they work with the stock risers. Hope that helps. Thanks for watching. ---Eric
Will the spiegler front brake line work with mini apes ? 8in handle bars .
Hello, Ismael, as long as the brake ling is the proper length and has the correct fittings it will work. Thanks for watching.
Where can I order those steel washers?
Give our customer care team a call. They should be able to track them down for you.
Is there specific cables that are required for yamaha star bolts? Or is it generic?
Joe Conerty We used Yamaha Genuine accessories for our Bolt. Found here www.chaparral-racing.com/ymm/2014-YAMAHA-BOLT-R-SPEC/Controls-Handlebars and www.chaparral-racing.com/ymm/2014-YAMAHA-BOLT-R-SPEC/Brakes
I like this handlebar, where can I buy it in Europe?
Hello, sorry not sure.
too bad, I would love to have it
These tall handlebars won't fit on the ABS model, correct? Or is there a workaround?
Why wouldn't they?
@@chaparralmotorsports hi I wanted to ask the same question. They don't wit with the abs model, cause the break lines don't fit with the abs control. Maybe I am wrong, but I couldn't find the right extansion that's abs conform. Would love to get some help. I realy need an ape hanger on my bolt
How do you remove the stock bushings to add poly bushings?
You've got to press the OEM rubber bushings out... before you can install the polyurethane bushings.
Looks good, lotta work. But that looks worth doing!
Hey togheter,
@Chaparral Motosports.
Nice Video- im from Switzerland an im also drivin a Bolt.
I want to install the origin Apes like you do in video.
Can you pls.tell what i exactly need for install.
I mean what kind of new parts like cables and others.
You will me make happy if you can tell me 👐👐.
Good wishes from Switzerland
Regards Kai
Hi Kai, thanks for watching our video, glad you enjoyed it. Here are the parts you'll need for the install, www.shopyamaha.com/product/details/tall-handlebars?b=Sport+Heritage+Accessories&d=47|47&f=2019|40&ls=yamaha-motor-company
www.shopyamaha.com/product/details/extended-length-braided-stainless-steel-control-ca?b=Sport+Heritage+Accessories&d=47&f=2019|40&ls=yamaha-motor-company
www.shopyamaha.com/product/details/extended-length-braided-stainless-steel-brake-line?b=Sport+Heritage+Accessories&d=47&f=2019|40&ls=yamaha-motor-company
You should also probably pick up some new hand grips as well. Hope that helps.
You are the best🤘🤘thank you so much.
Perfect
Thank you so much
You're welcome 😊
how the heck do you get the dang engine cutoff plug off of the holster it's on. I can't for the life of me get it off.
Hi, can you please tell us at what point in the video (time mark) you are referring to? Thank you
@@chaparralmotorsports I ended up getting it off. It was the part at around the 12:20 mark. The connector on the right had a tab on the top that was hidden really well that I needed to suppress to get the plug off of the frame. Needed to use a flat head.
Do you have a link for the Star Bolt extended cables?? Do you sell them on Chapparal.com?
Hello, yes we sell them. Here's the links:
www.chapmoto.com/yamaha-extended-clutch-cable-1tp-f63a0-t0-00
www.chapmoto.com/yamaha-extended-throttle-cable-1tp-f63b0-t0-00
www.chapmoto.com/yamaha-extended-front-brake-line-1tp-f58e0-t0-00
Do you have link to parts needed for the handlebar swap?
What is the torque setting for the riser nut?
Factory spec... would need to check the owners manual.
Need Help..
Is it possible to change handlebar for Bolt c spec
Thank you for your inquiry. Yes, all of the Bolt bars swap from one model to the next without issues. -- Kyle & the Chap Moto Team
@@chaparralmotorsports thank you very much for the reply.. if u hav any videos or pics on changing bars for bolt c spec ... thanks
Can you include the parts you used for the install?
Hi, thanks for watching our video. We used the Yamaha Tall Handlebars: www.chapmoto.com/yamaha-oem-handlebars-1tp-f61b0-v0-00
Yamaha Extended front brake line: www.chapmoto.com/yamaha-oem-extended-front-brake-1tp-f58e0-t0-00
Yamaha Extended clutch cable: www.chapmoto.com/yamaha-oem-extended-clutch-cabl-1tp-f63a0-t0-00
And Avon Grips: czcams.com/users/redirect?redir_token=SRbd1z0VBkp-PAZxPvS-JlQQu0Z8MTU4OTMwNjc0MEAxNTg5MjIwMzQw&q=https%3A%2F%2Fwww.chapmoto.com%2Favon-grips-custom-contour-grips-parent-317-9253&event=video_description&v=cUuWb6Or5AY
many thx for your video =D
+Cécile Guenot Your very welcome :)
How did you lengthen the wiring?
Hi, we didn't need to. It fit with the stock wiring. Longer cables were required though.
@@chaparralmotorsports How do I get longer cables for a 2017 Yamaha FZ07 ?
so i need all of these right ???? or do i just need 1 and 3 ? for a 2015 bolt bc the first one has 3 cables and the 2 one has just one and the 3 just one
1 Extended Length Braided Stainless Steel Control Cables 1TP-F63B0-T0-00$98.95 Options: Throttle Cable|Fits: 2015 BOLT
2 Extended Length Braided Stainless Steel Control Cables 1TP-F63A0-T0-00$72.95 Options: Clutch Cable|Fits: 2015 BOLT
3 Extended Length Braided Stainless Steel Brake Line 1TP-F58E0-T0-00$88.95 Fits: 2015 BOLT
+Paul Morgan www.shopyamaha.com/product/details/tall-handlebars?b=Star+Motorcycle&d=12|12&f=2015|40&dealernumber=&wi=true
+Paul Morgan Hi Paul you need all three.
#1 is the extended clutch line.
#2 is the extended throttle cables (this comes with two cables: the pull and the return cable).
#3 is the extended front brake line.
Hope that clears it up.
Goddamn so were looking at 400 bucks to get these bars on the bike?
More lights please!
Handled Cobalt. Thanks for watching! - Kyle & the Chap Moto Team
I'm ready to win august prizes. I can use that gift card. I'm favorite place on earth..
QWE
Sorry, what?