PLEASE PLEASE PLEASE explain why you think that the clutch pedal is tight because the clutch bolts are over tight!!! PLEASE DONT IGNORE THIS COMMENT!!!
Wow great job, I have similar problems in my Nissan cashqai … Inexperience junior Machanic said that I have received a wrong clutch …so I have to change again….be careful bad Machanic’s
Ok i got a 2012 xterra 4.0 standard trans. Im changin the engine to help a lady down the road. The engine she got came out of an automatic so im switching the flywheel n clutch assembly. But where the flywheel goes on the automatic, there's a big sleeve or something that sticks out from the back of the block that the standard doesnt have. I cannt install the new pilot bearing either with that in my way. Suggestions?
have enjoy your videos, i have d40 but haven't come across anything that answers my problem.(you may have done one but i haven't seen it) in short, after starting, it idols for 1-2 mins then revs up.
Hi i have nissan navara 2007 model 2.5 4x4 it has dual mass flywheel on all i want to know my clutch failed it burn can i only put a new clutch on the dual mass flywheel like a heavey duty clutch or must i put a new dual mass flywheel on with clutch or can i just put new clutch on because the flywheel is still 100% please reply?
So what was making the pedal hard? Just changed clutch and gearbox and now my clutch is hard to press and wants to shoot back up that it’s hard to hold at biting point.. thanks for help!!
Hi Des I have 2006 Navara d40 with 2.5dci (Renault engine on it) can you tell me if is a dual mass flyweel or single flywheel, need to get a new clutch fitted very soon and just want to be sure im getting the right clucth. THANK YOU. Ricardo from Madeira Island, Portugal.
Hi I have a Nissan xtrail 2005 petrol, manual gearbox, my gears are not catching. I've just replaced the MR20 engine. Is there perhaps a cable or two that needs to be set? The gearbox and clutch worked just fine before the engine replacement, please can you assist or guide me further, kind regards
Hi Des, thanks for great vids, I keep watching them over and over again. Could you tell me Des, how much would you charge for a clutch on a 2006 x trail? Thanks, Des, Paul
Hi Des Great job your a true professional I have a question for you I have a 2009 Qashqai but subframe is very rusty, Could I replace it. Keep up good work👍
hi des,,i have a 1996 nissan patrol,TD42 ENGINE,,my clutch slips when the engine gets hot,,returns to normal when engine cools down,,ive already replaced the clutch slave,,what should i do?
funny you shoud mention wheel nuts . a few years back i got a a lad to do front discs and pads . as i did not have the time to do them . he must ran the wheel nuts on with a impact . i had to snap 4 of the five studs to get the wheel off . lucky it happened on my drive and not the middle of nowhere
a 2016 frontier v6 4x4 6 speed I'm about to buy with 25000km on on it, the clutch grabs at the very top and all at once. 1 is that normal for these nissans with a 6 speed to drive like a dump truck and 2 is it adjustable?
Hi! I am a big fan of your youtube channel regarding Nissan and I am an amateur. I come to you because I really need your help!!!! My car is a Nissan Pathfinder 2007, 2.5 DCI. My problem is that somebody broke my cylinder head when putting back the fuel injectors when he screwed the screw too tight for the injector holder, big metal "V" shaped. The thread from cylinder head has been broken to pieces. Question 1: Cylinder bolts need to be changed at each detachment / change of the cylinder head? Question 2: Can you give me a list of torque per each screw from the cylinder head + injector screw torque ? Question 3: Can you tell me which Manufacturer of the cylinder head is the best to buy? ( besides of the OEM) Because the price is to high. I have in my country ( FAI, AMC, Engineteam, and Japan parts )
Hi and greets from Estonia! I have xtrail t30 and 2,2dci. 25000 km back I broke my clutch. Nissan service replaced clutch and flywheel with bearing. Now I have again broblems with clutch... cant belive that error what cause that is in flywheel or clutch. Previous clutch failure was that clutch wheel teeths was all broken!!! I think that this damaged gearbox shaft too and there is kinda step what dont let new clutch slide on gearbox shaft properly and sticks to flywheel when I try change gears. Is it possible, because i saw this old clutch and flywheel but offcourse i havent saw gerabox shaft when Nissan service doing last replace job. Is it possible that this gearbox mainshaft is damaged and causes next clutch failure? Sorry my bad english.
Hey Des, I've fitted a brand new clutch and its slipping, what could cause this? i removed the tranny again and theres no grease on the flywheel or the clutch itself... another problem.. its grinding when im changing gears. could a bad spigot bearing cause this? many thanks From Australia
You could have fit it too slack but i do not think you have i still feel it is faulty or when you say grinding when you change gears the gear box could be damaged
Hi Des, I purchased a brand new Navara NP300 with petrol engine 2.5L, 7 months ago. Now that I hear noise coming from clutch, as it goes while pressing the clutch, a mechanic suggested to replace it. It has traveled 22k KM. What do you think about replacing or even upgrading the clutch?
I do really enjoy your videos. Also my nissan pathifinder heater is blowing out the air but no heat what so ever ANY IDEAS? also i got the other problem on my pathfinder solved when it was not reving above 2500.It was the crank shaft sensor 👌
Nissan Qashqai 2010 accenta 1.6 it gives a clutch problem, the pedal just went down while I was busy driving and stays there without return. This is not the first time .can any one help
Hi, I have had my clutch and flywheel changed (LUK) and I am having now vibrations at idle (as if the idle rpm was too low) and also from +/- 80km/h and up. Any ideas what could be wrong? Thx.
50% of the reason why I left a dealer for a major global manufacturer was because of the disgusting use of impact equipment for dismantle & reassembly.
Hi Des I’ve a Nissan NV200 with 14k on the clock , just 3 years old . For over a year it’s been back and forth to dealers about a judder from 1st gear when pulling away , they say they cannot find anything wrong despite road tests with me and it’s doing it . However today it’s just had its 3 year service and they say ....... your clutch is worn out . That’s the juddering. It’s £1000 to replace and not in warranty. They say it’s either too much weight in my van , too heavy a trailer or I’m leaving my foot on the pedal . It’s none of them . I’ve only got very short legs so I have to lift my leg to push clutch in , so uncomfortable to leave foot in air , plus my other 2 cars and works lorry have no clutch issues . Trailer is for moving plants from allotment, few Kg not tonnes . And only a lawnmower and 4 tool boxes in back . If I go into a high gear and put handbrake on and try to pull away it will stall immediately. If I’m going along in 5th the revs are low but speed is ongoing , will reach 90 easily and keep going , pulls trailer without fault . The judder is only when pulling away in 1st , no other gear . I don’t believe the clutch is shot ? Have you any views ??? Dan
Dan, I have this exact problem after having my Nissan Pathfinder clutch replaced. Did you ever get it resolved? Anyone else got a solution?! Thanks Matt
Gday bro love your videos I don’t think there’s anyone better out there love my Nissan Navarra had cracked head replaced in 2019 and is only now running rough noisy and blowing smoke timing chain wasn’t replaced I put a plug n play power chip in and a egr blank off plug n play mod and throttle wind booster controller to eliminate lag seems to work only up till 3500 rpm then cancels out losing power and blowing lots of black smoke then I cruise in idle for a few seconds it resets but my problem now is my clutch was done by a Machanic and is only 12 months old clutch is now slipping really bad so getting that done by another Machanic I’ll inform them about the torque settings and not to use rattle gun But my engine is my worry I wish I could bring my vehicle to you but alas I’m here in north australia Queensland 👍🏾
@@westyorkshireengineservice9160 thanks for your reply bro I’m bringing the car back to the same Machanic that installed the clutch and solid fly wheel conversion kit apparently the cba clutch kits are stronger than the exedy and so is the modified exedy called the dps 40% more clamp Cl here in australia any way I’ll keep in touch I’m bringing my d40 into Westco Nissan to get a diagnostics done for the rough idle and noisy tappet or injector noise at rough idle and acceleration also starting to show signs of blowing smoke on idle and stinks not a nice deisel smell
Dear Des, I am unsubscribing from your channel, you talk the talk but don`t walk the walk, basically mate, you are all talk. I have emailed you on I think 3 separate occasions, and also left a comment, asking for a price for a clutch and you have completely ignored me. Waste of space mate.
I'm a retired mechanic, so true your comments re:- air guns verses tourque wrenches. Video's and explanation are spot on. Thank you.
Hi guys M driving navara 2,5 was always going well because of your vedios thnx for sharing
Thank you for your kind comment that was our intension
PLEASE PLEASE PLEASE explain why you think that the clutch pedal is tight because the clutch bolts are over tight!!! PLEASE DONT IGNORE THIS COMMENT!!!
yeah just what i thought,can't be true.
koen van geleuken this guy talks absolute shite!
Professional to the core ! Love the vid.
Wow great job, I have similar problems in my Nissan cashqai …
Inexperience junior Machanic said that I have received a wrong clutch …so I have to change again….be careful bad Machanic’s
I have this excessive vibration through out the rpm range. From idle to 4k rpm. It gets worse at 2k rpm. Please help.
Andy Australia tasmania, lots of good info ,,,pitty nissan didnt have the same helpful attitude ,,,
Does it help to hammer the engine first before hammering the bolt?
Didnt do any harm.
absolutely agree .....amazing video mate
thank you for videos ..they are really helping me a lot..am Richard from Zimbabwe
Ok i got a 2012 xterra 4.0 standard trans. Im changin the engine to help a lady down the road. The engine she got came out of an automatic so im switching the flywheel n clutch assembly. But where the flywheel goes on the automatic, there's a big sleeve or something that sticks out from the back of the block that the standard doesnt have. I cannt install the new pilot bearing either with that in my way. Suggestions?
have enjoy your videos, i have d40 but haven't come across anything that answers my problem.(you may have done one but i haven't seen it) in short, after starting, it idols for 1-2 mins then revs up.
Hi i have nissan navara 2007 model 2.5 4x4 it has dual mass flywheel on all i want to know my clutch failed it burn can i only put a new clutch on the dual mass flywheel like a heavey duty clutch or must i put a new dual mass flywheel on with clutch or can i just put new clutch on because the flywheel is still 100% please reply?
Big no impact guns on clutch’s your right not to use it. I do them up by hand and corner to corner if you get me lol
So what was making the pedal hard? Just changed clutch and gearbox and now my clutch is hard to press and wants to shoot back up that it’s hard to hold at biting point.. thanks for help!!
Hi Des
I have 2006 Navara d40 with 2.5dci (Renault engine on it) can you tell me if is a dual mass flyweel or single flywheel, need to get a new clutch fitted very soon and just want to be sure im getting the right clucth.
THANK YOU.
Ricardo from Madeira Island, Portugal.
Hi I have a Nissan xtrail 2005 petrol, manual gearbox, my gears are not catching. I've just replaced the MR20 engine. Is there perhaps a cable or two that needs to be set? The gearbox and clutch worked just fine before the engine replacement, please can you assist or guide me further, kind regards
Use a torque wrench, don't use an impact gun, 4:41, the best advice in a loooong time, if only more people will realise that.
Over torquing clutch bolts wont cause the clutch pedal to go tight!
@Stem Artin exactly! This guy is clueless. Wstch some more of his vids, hilarious.
Hi Des, thanks for great vids, I keep watching them over and over again. Could you tell me Des, how much would you charge for a clutch on a 2006 x trail? Thanks, Des, Paul
Hi Des
Great job your a true professional
I have a question for you I have a 2009 Qashqai but subframe is very rusty, Could I replace it.
Keep up good work👍
Des you're the man.
Cheers from canada mate.
Good on you sir
Des your awesome mate!!
Thank you for your videos
Cheers Pal, All the best.
hi des,,i have a 1996 nissan patrol,TD42 ENGINE,,my clutch slips when the engine gets hot,,returns to normal when engine cools down,,ive already replaced the clutch slave,,what should i do?
funny you shoud mention wheel nuts . a few years back i got a a lad to do front discs and pads . as i did not have the time to do them . he must ran the wheel nuts on with a impact . i had to snap 4 of the five studs to get the wheel off . lucky it happened on my drive and not the middle of nowhere
Hi Des,I hate duel mass,I'm thinking of fitting solid flywheel conversion,fitted one on our car,best thing I did.any verdict on it
Good choice buddy
DMF is there for a reason.
Thanks for that.
a 2016 frontier v6 4x4 6 speed I'm about to buy with 25000km on on it, the clutch grabs at the very top and all at once. 1 is that normal for these nissans with a 6 speed to drive like a dump truck and 2 is it adjustable?
I use those easy outs best thing ever especially if you have 24 to remove where bolt heads have rotted away.
Many thanks Des and team you are hero's
Hi! I am a big fan of your youtube channel regarding Nissan and I am an amateur.
I come to you because I really need your help!!!!
My car is a Nissan Pathfinder 2007, 2.5 DCI.
My problem is that somebody broke my cylinder head when putting back the fuel injectors when he screwed the screw too tight for the injector holder, big metal "V" shaped. The thread from cylinder head has been broken to pieces.
Question 1: Cylinder bolts need to be changed at each detachment / change of the cylinder head?
Question 2: Can you give me a list of torque per each screw from the cylinder head + injector screw torque ?
Question 3: Can you tell me which Manufacturer of the cylinder head is the best to buy? ( besides of the OEM) Because the price is to high. I have in my country ( FAI, AMC, Engineteam, and Japan parts )
Caută manualul de service pe net , găsești acolo torque, proceduri de înlocuire.
I changed my car's clutch kit. My clutch pedal is too hard. What could be the problem? What should I do? brand of clutch kit exedy
(D22 yd25)
Hi good day our navs don't stretch the chain so much, mine got 320 thousands killos. oil change at every 5000k.
G'day, where do you get the technical data book for an 2004 Navara D22 ZD30 motor? Thanks.
Good job!, nice work, you're so right about impact gun usage, its not professional! Regards Des.
Hi and greets from Estonia!
I have xtrail t30 and 2,2dci. 25000 km back I broke my clutch.
Nissan service replaced clutch and flywheel with bearing. Now I have again broblems with clutch... cant belive that error what cause that is in flywheel or clutch.
Previous clutch failure was that clutch wheel teeths was all broken!!! I think that this damaged gearbox shaft too and there is kinda step what dont let new clutch slide on gearbox shaft properly and sticks to flywheel when I try change gears.
Is it possible, because i saw this old clutch and flywheel but offcourse i havent saw gerabox shaft when Nissan service doing last replace job.
Is it possible that this gearbox mainshaft is damaged and causes next clutch failure?
Sorry my bad english.
Hey Des, I've fitted a brand new clutch and its slipping, what could cause this? i removed the tranny again and theres no grease on the flywheel or the clutch itself... another problem.. its grinding when im changing gears. could a bad spigot bearing cause this? many thanks From Australia
Usually a new clutch needs to brake in. It need city driving a bit.
Hi you know the clutch could be faulty.
Surely theres some tests i can do when the clutch is out?
You could have fit it too slack but i do not think you have i still feel it is faulty or when you say grinding when you change gears the gear box could be damaged
MrJuicycreative
I like your accent, I'm a southerner😊
excelente como siempre saludos desde chile puerto montt
Des I’ve just done a google search on your company and it comes up with you scamming people? Can you please explain?
Hi Des,
I purchased a brand new Navara NP300 with petrol engine 2.5L, 7 months ago. Now that I hear noise coming from clutch, as it goes while pressing the clutch, a mechanic suggested to replace it. It has traveled 22k KM. What do you think about replacing or even upgrading the clutch?
That's input shaft bearing buddy. Its inside gearbox. But when you put clutch in and you hear rattling that's throw out bearing outside of gearbox.
I do really enjoy your videos. Also my nissan pathifinder heater is blowing out the air but no heat what so ever ANY IDEAS? also i got the other problem on my pathfinder solved when it was not reving above 2500.It was the crank shaft sensor 👌
1 Check coolant
2 Check combination servo motor\motors(dual side climate) from dashboard
Nissan Qashqai 2010 accenta 1.6 it gives a clutch problem, the pedal just went down while I was busy driving and stays there without return. This is not the first time .can any one help
Could be master cylinder leak
Hi how much to do my cluch on a Nissan qashqai ntec 6 speed .2.0 petrol??
Hi, I have had my clutch and flywheel changed (LUK) and I am having now vibrations at idle (as if the idle rpm was too low) and also from +/- 80km/h and up. Any ideas what could be wrong? Thx.
Input shaft bearing inside gearbox
Hi guys great video again..... I'm looking to swap my gearbox oil do you have an idea on how much my 2.5 5 speed box takes please.
Dont take it to this man he is clueless!
Hi Des do you have any video that shows or guide on how to fix a snokle ?
No sorry bud
Is there any positives with a Nissan
50% of the reason why I left a dealer for a major global manufacturer was because of the disgusting use of impact equipment for dismantle & reassembly.
Hi Des
I’ve a Nissan NV200 with 14k on the clock , just 3 years old . For over a year it’s been back and forth to dealers about a judder from 1st gear when pulling away , they say they cannot find anything wrong despite road tests with me and it’s doing it .
However today it’s just had its 3 year service and they say ....... your clutch is worn out . That’s the juddering. It’s £1000 to replace and not in warranty.
They say it’s either too much weight in my van , too heavy a trailer or I’m leaving my foot on the pedal .
It’s none of them . I’ve only got very short legs so I have to lift my leg to push clutch in , so uncomfortable to leave foot in air , plus my other 2 cars and works lorry have no clutch issues .
Trailer is for moving plants from allotment, few Kg not tonnes . And only a lawnmower and 4 tool boxes in back .
If I go into a high gear and put handbrake on and try to pull away it will stall immediately. If I’m going along in 5th the revs are low but speed is ongoing , will reach 90 easily and keep going , pulls trailer without fault .
The judder is only when pulling away in 1st , no other gear .
I don’t believe the clutch is shot ?
Have you any views ???
Dan
Dan, I have this exact problem after having my Nissan Pathfinder clutch replaced. Did you ever get it resolved? Anyone else got a solution?! Thanks Matt
Your sound/audio is not clear enough...Sorry!!
Thanks
Gday bro love your videos I don’t think there’s anyone better out there love my Nissan Navarra had cracked head replaced in 2019 and is only now running rough noisy and blowing smoke timing chain wasn’t replaced
I put a plug n play power chip in and a egr blank off plug n play mod and throttle wind booster controller to eliminate lag seems to work only up till 3500 rpm then cancels out losing power and blowing lots of black smoke then I cruise in idle for a few seconds it resets but my problem now is my clutch was done by a Machanic and is only 12 months old clutch is now slipping really bad so getting that done by another Machanic I’ll inform them about the torque settings and not to use rattle gun
But my engine is my worry I wish I could bring my vehicle to you but alas I’m here in north australia Queensland 👍🏾
Hi buddy check the top tensioner you may have put too much RTV on the back timing plate so if it’s not getting enough oil that’s the fault
@@westyorkshireengineservice9160 thanks for your reply bro I’m bringing the car back to the same Machanic that installed the clutch and solid fly wheel conversion kit apparently the cba clutch kits are stronger than the exedy and so is the modified exedy called the dps 40% more clamp Cl here in australia any way I’ll keep in touch I’m bringing my d40 into Westco Nissan to get a diagnostics done for the rough idle and noisy tappet or injector noise at rough idle and acceleration also starting to show signs of blowing smoke on idle and stinks not a nice deisel smell
Dear Des, I am unsubscribing from your channel, you talk the talk but don`t walk the walk, basically mate, you are all talk. I have emailed you on I think 3 separate occasions, and also left a comment, asking for a price for a clutch and you have completely ignored me. Waste of space mate.
G'day, where do you get the technical data book for an 2004 Navara D22 ZD30 motor? Thanks.
thank you for videos ..they are really helping me a lot..am Richard from Zimbabwe