MAGNETIC PAINT | Cheaper and easier than Ferrofluid and Ferripaste?
Vložit
- čas přidán 19. 06. 2024
- Ferrofluid is amazing. I wish everyone could experience it in real life, but it is expensive. Perhaps there is a cheaper alternative in your local store: Magnetic paint!
In this video, I test the weird paint and compare it to ferrofluid and my own creation: ferripaste. How well does magnetic paint work in comparison? What are the fluids' strengths and weaknesses? Is one of the disadvantages of paint actually a useful feature?
Let's find out!
One of the 150x50 mm disc magnets donated earlier by www.magnetportal.de/
Ferrofluid and 70x35 mm magnet donated earlier by supermagnete.com:
Ferrofluid: sumag.net/ferrofluid-x05
My Patreon-page: / brainiac75
Links to other videos with a similar topic:
How to make Ferripaste: • Magnetic Motor Oil? | ...
Ferrofluid vs. Ferripaste: • BURN IT! | Ferrofluid ...
Monster magnet meets magnetic fluid...: • Monster magnet meets m...
Did you miss one of my videos?: / brainiac75
FULL MUSIC CREDITS
Time code: 0m:1s
"Martian Cowboy" Kevin MacLeod (incompetech.com)
ISRC: USUAN1100349
Time codes: 1m:14s + 7m:54s + 11m:45s
"Perspectives" Kevin MacLeod (incompetech.com)
ISRC: USUAN1300027
Time codes: 3m:45s +10m:1s
'Fluidscape' Kevin MacLeod (incompetech.com)
ISRC: USUAN1100393
Time codes: 5m:52s + 14m:42s
'Long Note Three' Kevin MacLeod (incompetech.com)
ISRC: USUAN1100424
Time codes: 6m:23s + 10m:49s
'Impact Lento' Kevin MacLeod (incompetech.com)
ISRC: USUAN1100619
Time code: 7m:4s
'March of the Spoons' Kevin MacLeod (incompetech.com)
ISRC: USUAN1700008
Time code: 13m:56s
"Rising Tide" Kevin MacLeod (incompetech.com)
ISRC: USUAN1900010
All music above licensed under Creative Commons: By Attribution 3.0 License
creativecommons.org/licenses/b...
Time code: 9m:35s
Mix of two tracks:
1) The Shimmering by fran_ky (freesound.org/s/237363)
Licensed under Creative Commons 0 license
2) 'Spacial Harvest' Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 3.0 License
creativecommons.org/licenses/b...
ISRC: USUAN1100653
#magnetic #paint #ferrofluid - Věda a technologie
Probably someone already suggested this but you can cast it in a epoxy resin. It will be challenging but I'm sure in the end, you will have a relic from an ancient alien civilization.
Was about to say that lol.
Second this
If you could get the spikes/ridges small enough, this could be a Vantablack killer.
You mean "create a soupy mess"?
@@MadScientist267 What do you mean by that?
"Don't let fire play with *you* !" //
"The cleanup really puts the pain in paint."
Love it! 🤣
How is it bold? I can only do italic and I can put a line on the words.
_I_
-S-
ideas : Start with some base layers of non-magnetic paint. Encapsulate the dried paint sculpture in clear resin.
great idea! i'd carefully airbrush them some cool metallic color before! the matte black makes details and crevices way hard to see. but those structures might be quite a challenge to encase bubble free, without a vacuum chamber.
My thoughts as well. Start by preparing a base of thickly layered acrylic, allowed to fully dry in advance. Add one more coat and allow it dry just briefly so you have a tacky surface to begin with. That way the ferro paint will adhere quite well to the acrylic base.
For resin, I think you could brush on numerous coats of clear acrylic to fill fine gaps and delicate texture, prior to encasing in resin.
I like the spikes of ferrofluid. But I also love the ridges in this paint. They form patterns that look like roses or carnations. To me, this paint is just as beautiful. I'm sorry you had a messy clean-up.
Thats soooo cool! :D
Maybe you could try to coat the Sculptures with a layer of UV resin or even put it in a block of clear resin! ^^
Must admit I did not expect it to be this close to ferripaste... What I really want the most, is to make it more glossy. It is a quite matte when dried. I guess high gloss UV resin would fix it? Thanks for the early watch and comment as always!
@@brainiac75 Orange LED Strip
Oops, I should have read all the comments before also sorry heating to cast it in resin. Haha
@@brainiac75 a quick search shows that UV resin is available in viscosity down to as thin as water. You could dip it then hit it with UV to create a protective shell. Depending on the formulation, maybe one of those would give the gloss finish?
@@brainiac75 i was also thinking about this iu think it would look cool to put it in a resen block and use a led base for display
You changed the phrase of watching the paint dry
13:59
Why did this part crack me up so much lmao
Guess we have the same sense of humour? I laughed way too hard at it myself x) It was just one of those long 10 hours editing days where the 'slide shows' at the end felt too serious and repetitive for me. Decided to break it up and entertain myself (and hopefully my viewers too) with that gimmick. Thanks for watching!
Very nifty! Never seen magnetic paint before
Did not think the paint would work this well. I got carried away and made my longest video yet... For video, it is too matte though. Looks better in reality. I may need to invest in a camera with higher dynamic range and HDR capabilities :D Thanks for the early watch and comment!
@@brainiac75Putting a black fluid in a white container may have made the camera "stop down" to reduce the white, which starved the black for exposure. A deep blue or strong red background might show off the black better? (Is what I was thinking before I got to the Comments section. I hesitate to mention this to such a pro, though!) Thanks for the Art + Science today.
I think it'd be a great idea to experiment with a wide range of values for the parameters like distance, layer thickness (volume of the paint you're pouring) and water ratio.
I also think it'd be interesting to see if it can be airbrushed for example on scale model kits
You tried adding water, but to make particulate mixes thinner without changing their concentration, you want to make them slippery - this is why surfactants, basically soap, are used as plasticizers in concrete. Maybe add a few drops of Dawn or other highly concentrated liquid soap, and see how that goes?
Yes - another video from Brian😊
12 years and no subscribers? Just changed that!
@@when-the-hnow it's 2
Oh yes, and the longest one yet ;) Quite an effort on a winter fatigue... Thanks for the early watch and comment!
@nma794 You spelled it wrong. It's Brain. Last name appears to be Iac.
It makes me happy to see a new video from you
8:20 Ferrofluid has been around for over a decade and I just now learned it's flammable.
paint a wall with it and test the sound proofing properties of the spikes, due to the shape of them they should provide some pretty efficient sound proofing.
The humour is improving, and your usual deadpan delivery makes it even better.
Thank you! Keep producing videos!
You're welcome! I have only been uploading videos for 14 years ;) Not even close to being ready to retire! And thanks for the early watch and comment.
I nearly posted this on your older video, but glad I continued the binge. For thinning duty, easy-access surfactants can be had under several everyday products. While ordinary dish soap works to a degree, what you're really after are tannins. Green tea has a relatively high concentration of tannins, though they're quite easy to buy in bulk as its own product. This is also the 'secret' ingredient that keeps clay particles in suspension if you've ever had a play with glazes.
Your carrier can be an effective solvent (can make recommendations depending on your locale; in the US, acetone and MEK substitutes like xylene are easy to acquire), IPA or even the universal solvent, distilled water. Basically the purer the better to avoid mineral contamination.
Ferrofluid works as it does as the ferromagnetic material is broken down to nanometer particle size, often in its carrier of choice during the same reducing process. You can add your mixture into a glass jar in an ultrasonic cleaner for a few cycles and enhance functionality, or if you have a sufficiently powerful blender for Science duty. It will need quite a lot of shearing time to get break down into the finest concentration (90 minutes would be my starting recommendation, but most blenders are not rated for that kind of duty cycle, even the commercial ones. I have a graveyard of sacrificial blenders including a 1500 watt commercial rig).
yey i have waited for this for so long!!
For the sculpture, using an electromagnet will make it easier to remove.
Keep going my man! Love your work
Maybe a new camera or lens for such colours/materials
Thanks. As long as you all watch and like my videos, I have no reason to stop. Much more to come!
This already made my day
Fed video Brian!!🫡❤️
educational and entertaining, your videos are awesome!
That stuff is amazing! I think I am actually inspired to art after years! Thanks s much! You could probably add other arcylic mediums, for different textures, or shapes. And would make more damage resistant structures, because I assume it is very fragile when dry.
Huh... would look very interesting to mix a some of that 'Black 3.0" acrylic paint (it's pretty much vantablack). Have yet to get that paint myself... ugh... Would make amazing depth or no depth! I can't imagine that space scenes I could create! wow!
Du er bare den bedste Brian !
- Skal da ned i hjem og fisk i morgen . . .
Tak for alle dine gode videoer.
Mvh Petter
Making a DIY Ferrofluid is so satisfying.
What a nice magnetic flower you made there.
Great video! You've made me want to experiment with magnetic fluids myself now :)
Thanks. I highly recommend it - looks better in real life. Though the clean-up can get very tedious if you are not careful ;)
Incredible
The paint could be great for dioramas. Or some sort of tapletop map. Imagine you have a part of the map that belongs to a villain. If you made a bunch of those sculptures and squared them off, they could make great terrain pieces
Excellent!
YOOO LET'S GO NEW VIDEO
Oooh! For the sculpture, casting it within an acrylic block would look very cool!
Edit: looks like a few others had the same idea. Haha
If you used a plastic box, put some of the paint inside above the magnet and allowed it to form the spikes then slowly and carefully flooded the box with clear resin I wonder if you could permanently encapsulate the spikes
Super glad you decided to stir it first lol
Painting a layer first without the magnet would solve the base being separate spikes.
In my opinion, the blades and ridges of the earlier recipes look the best. They're really cool looking
This is much better than regular ferrofluid because it's much more viscous and shows a much higher definition shape of what the magnetic field looks like.
Ferrofluid is kind of a one-trick fluid with the same pattern over and over. But what a trick it is ;) With that said, I found the magnetic paint to be much better than I expected. Just need to gloss it up for better visuals! Thanks for the early watch and comment as always, Aaron.
Very cool! I would try to pour a small quantity first and let it cure for a while, but not fully. Then put it on the magnet and pour some more paint on it. Hopefully this will create a solid base.
please demonstrate an inductor coil's pattern of magnetism via various ferrofluids, thanks.
Good idea, though in my experience a bare magnet at some distance has the most interesting effect on ferrofluid. Will consider a video, where I use electromagnets, inductor coils etc. on ferrofluid. Should be possible to make some interesting patterns with a bit of creativity. Thanks for watching and the suggestion!
I guess that's the most fascinating paint you'll ever see.
It sure is the most entertaining paint, I've used ;) Thanks for the early comment and watch!
This stuff has its own value with its own unique shapes
I love your videos.
I build model kits and this would look really cool painted on a mecha model. I have to try that!
7:10 I think a rubber spatula (the one used for mixing bowls for home baking) would be better at scraping the magnet paint off the tub!
Some ideas for you:
1. Explain how the levitron spinning top works.
2. Try different form of magnetic bearings - active and passive kinds
3. With small magnets the can lift themselves up in a glass dish with ferrofluid, can your larger magnet lift itself too? Is the high of lift Higher or lower and does the ratio to gauss to size matter?
4. If the large magnet can lift itself how much can it hold compared to the smaller magnets by pounds/kilo to gauss.
5. Can you get on the magnet and take a spin on ferrofluid?
I triple-dog-dare you to paint all your walls with this, braniac!
Hello new miniature scenery building technique. So many possibilities to try.
Very fascinating process! It's always enjoyable to follow along with a trial-and-error process, it scratches the inquisitive itch.
I must say, I really enjoy the visual interest of the blades that the paint formed (possibly more than the Ferro fluid spikes) as they all seemed to form into something truly unique every time. Very interesting!
That is very cool
It would be neat to see a ferromagnetic sculpture in casting resin.
It would be nice to have the option to use different colors. I expect you couldn't make the paint itself lighter due to the iron powder. But perhaps it would be possible to apply a coat of color to it. Also I'm not sure if that should be applied before or after the magnetic paint has fully cured for the best results. Either way, without first applying a lighter base coat, I'm not sure if you could get vivid colors anyway. And thicker or more layers will probably hide a lot of the finer details.
I wonder if it would be possible to coat the spikes with a UV-A reactive substance. Or perhaps even better, mix it into the magnetic paint right from the start. That way you're not dependent on a color "overcoming" the black paint in order to give it a very vivid appearance. As an added bonus, it could also help to bring out all the details.
now if you could get it to dry in formation on your wall. ❤ great video 2x👍
Thanks🎉
You're welcome and thank you for the very early watch and comment, Johnny!
This is genuinely interesting. What practical purpose would magnetic paint have for it to be commonly sold? Though, I'm surprised at how close it is to Ferripaste. Great video as always--and not what I expected. A follow-up to this would be quite interesting, to see what you'd do with the sculptures.
not sure if this is related, but a while back LTT made a video showcasing conducting paint for RF blocking purposes.
It's used for making magnet boards so you can hang things up with magnets like a fridge. You can also use it with chalkboard paint to make magnetic chalk boards.
hmm, using the paint on glass and spray painting a protective top coat, maybe a automotive primer, could make a sturdy enough desk piece, you could also make color transitions or add texture to the final work
...or casting as a paper weight?
6:18 It looks like an evil flower, beautiful
The wargaming community seeing you can add ferropaint spikes from Hell to the mini bases and boards: "Write that down!!!"
I actually thought the blade formations looked cooler than the spikes. Looked like some kind of flower from a Tim Burton movie.
Our clothes dryer recently died and I took it apart and found a good 300g of ultra fine iron dust inside. I immediately thought of this channel when I found it. The dryer had been grinding it’s parts for years.
You could try Masking fluid. Its an artistic preservative used on water based art mediums.
Something to try sometime. Mix iron powder into a slow curing resin, then let it harden in a strong magnetic field
to give your sculpture a solid bottom layer you could make a bit of a rim, pour in some normal black acrylic first, then the magnet paint. that should give you a disk for the spikes to sit on.
I like how you were able to get thin spikes. If you did it on a thin piece of silicone rubber mat or similar thin silicone rubber and poured regular acrylic black paint or black coloured uv resin around and worked it through the base of the sculpture you may be able to remove it ?
A silicone spatula is really good for getting thin layers of residual liquid off of the bowl.
I think you might be able to fluidize the gritty magnetic pigment by vibrating the paint above the magnet. Have you any sort of vibrator to make the spacer board hum, while the spikes are forming? Some possibilities: An aquarium air pump, hair clippers, a saber saw (without blade), a small DC motor with an off center weight (like those that make a phone vibrate). Adding a thin foam layer between board and magnet would let the board vibrate more easily.
Hi Brainiac!
I came across some internet sources stating that 365 nm light can eliminate fungi and eradicate certain pathogens, such as bacteria. I find this information quite intriguing, considering that 365 nm falls within the UVA range, which is relatively weak.
It would be great if you could create a video experimentally testing this phenomenon using a 365 nm black light.
Thank you!
could look dope if you put the dried spikes in resin an added underlights a unick light feature
With the cracks in the base of the ferropaint, I'm thinking it'd be interesting to put some multicolor LEDS under it in a box/stand and then a glass cover.
It seems you are not a big on cooking :) There are amazing silicone spatulas, with you could quickly and effectively scrape off the paint from any flat surface, or slightly curved even.
Nice pair of B&W speakers, are these the 601 line? I have the original model, looks like you have 601 s2 maybe, they do soind awesome though :)
Nice👌
13:59 the fact this is part of the video makes this video even more entertaining 🤣
I like the blades. They look organic like flower petals.
It's fascinating how it almost looked plant like, flowering like petals
Could you use those silicone moulding kits on these? Then create a cast from them?
I think the paint looks great, I think it would be interesting to put a coil of very small LED on the plate and let the paint dry. Some light would be buried, but there might be some good light to accent the depth.
Assuming they're resilient enough and don't break down over time I bet you could use it to make some sound treatment panels (like those black edged ones made of foam that people use).
You should definitely sink a (much smaller) sculpture into a half dome of crystal resin, so the resin would act as a lens, magnifying it.
on a large scale maybe this could make very interesting looking sound absorbing panels
When does the part 7 of Exotic Elements vs. Magnet coming? 😂
Is it possible to do a video with radioactive and really dangerous elements you have not already tried?
each one of your patreons will get their own plastic sheet with some dried up spikes. 10:57
thats wicked, and it incl. all tiers.
Just make sure you package it well.
You could set it in a block of clear resin for a mantelpiece sculpture
Which strength is the smaller round magnet used is the video please ?
Could you wash some of the acrylic resin out with water IPA, while it's on a magnet adding something to break up the water tension and something like glycerol?
Do it on a grid of magnets next!
you could flow some more paint in the base to connect the spikes
Noice! Maybe you could buy clear two part epoxy and mix in black iron oxide, you might get a similar result but way more sturdy.
Since it's an acrylic paint, cleanup should be much easier if you play with it in a silicone or silicone coated container. Once it dries flexing the container should make it delaminate. My only concern is that maybe the iron particles would tear up the silicone coating.
oh man my head is full of ideas, you could make miniatures cover them with the paint and then use magnet to give them a texture.
If sturdy enough, encasing it in a thick block of resin to make a paper weight or similar?
Is that from Harald Nyborg? have you considered other brands?
Check for fire resistance, seemed it could dissipate the heat well
You should add a colorshifting interference pigment to it.
What would happen if you added some bismuth (diamagnetic) powder and mixed it up with the ferrofluids?
Would it help loosen the iron , or just separate out?
How about spraying it with lacquer and then using it as a magnetic sound wall?
Try encapsulating the feropaint "art" in epoxy before removing it. Actually... might be interesting to see how that would work with the ferofluid and feropaste too.
I wonder if you can make a iron "shell" on parts by applying few layers of paint on plastic wrap. peeling it and burning away the acrylic resin, then sintering the iron particles.
Never thought I'd say, watching paint dry was interesting! 🤣
I wonder if you could do something with two magnets on either side of the paint?