New 20x20 cm Dry Cell
Vložit
- čas přidán 26. 10. 2010
- This is a 20x20 cm circulating cell. The output performance is 12.5 volts at 25 amps produced 500 ml of HHO in 17 seconds. The efficiency of the cell is a 5.65 MMW. The operating temperature is 135 F to 147 F
- Věda a technologie
very very nice work. in fact their are a few talented folks out there working on this. I really like you gave some details on how the system works. really helps people who are researching. I am also working on a few cell designs my self and I also see that this could make one hell of a space heater. Thanks again for the post.
I enjoy your presentation explaining your steps and your information measurements. I would really like to enjoy seeing it assembled and that would explain a lot more to me and for me. But all in all it looks great and it looks like it'll work.
At last we have a very neat system and a clear description of an HHO system with facts and figures to prove it's practicality......good work, very well done.
It looks like you have a 4 plate separation between + and -
Try this setup with 2 more plates on each side of the negative plate to lower the temperature and increase efficiency. Or at least make sure you stay within the 2V between each plate. A cell warmer than room temperature means you are wasting energy. Thanks for sharing
That free place without water at the top creates an unstable electrolysis. I found the solution. Otherwise a good job, clean and beautifully worked 🙏👍
This happens only in dry cells.
Hey Bernie. Working on the heater too. Need to make a smaller hydrogen separation cell first. Should be ready before it gets real cold.
Great man. Big Conversion.
The black stuff is a rubber gasket. They are non conducting and are used to separate the plates to give room for the water to circulate.
Dano thanks for the kind words. I can't wait till the KZX1250 PWM gets here!
what do you use for PWM? How goes your progress?
Great love to buy one from you
Exelent job.
Reducing KOH concentration will lower the flow rate slightly but the heating problem can be solved. I generally use 35 to 55 grams in one liter of distilled water, the temperature never goes above 40ish with ambient at 30c.
wow best out/cell area fuel cell ive seen great work really congras im working on doint one myslef quite a bit smaller i just need 800ml per minute for my car so thats what im aiming for at the moment sut one question how many neutral plates do you leave between pos and neg ones? have u tried differente set ups on how many u leave in between so far my best has been with one noutral between pos and neg but ive seen many use 3 or more so i might be doing something worng :P any ideas?
This is a key feature. The holes in the plates are offset. They are not drilled in the center of the plates. When you alternate the offset holes it forces the water to travel over more of the surface area of the plates.
What do you mean you staggered the holes at the bottom? And which holes exactly? In the plates? I'm Dutch, can you give another explenation for that? Thanks.
very nice work
Many thanks
Compact size, suitable for making fuel cells for motorcycles.
Imagine forgetin about it runin. And then at morning trying to light joint
Reminds me of a high effiencey washing machine!
May you let us know which plastic you have used to bind hho plates?
One question you only put two holes on the top between each plate and none at the bottom?
are you using something to get that amperage from it?
Question: Can you up the voltage to 24VDC and halve the amperage [12.5 - 13amps]? Will that change output? How will the system perform in winter weather?
Could you put a small computer fan above it to protect it from overheating if you ever installed it in the vehicle to use it.
The cell temp stabilized around 75c. at 25 amps.
I was using a power supply that can run up to 50 amps.
This transparent 'glass' window is plexiglass or solid polycarbonate?
I have a dry cell , it fitted in my Chevrolet spark . But reduced the average after installing.. how it will improve .
It looks more than 1.76LPM but I watched a Portugese video with a beautiful looking wet cell design claiming 6-7LPM with a gauge but it didn't look that much. I thought maybe he was using an ounces per minute gauge or something like that. Yours APPEARS to be producing well but your bottle test says otherwise.
how is the concentration of koh in water at 25 amps
gas is measured in liters or in mc ?
Hi, it looks great. what have you added to the water,
and what is the temperature of the cell and the temperature in the reservoir?
Due to having the neutral plates , the voltage devides and thus temp is not raised
Goddamit man, get yourself a tripod.
Here Now LOL
good day just have a quick question about this hho video, what happens when you bump up the voltage, why did you stick with 12 volts.
The optimal voltage for the electrolysis occurs around 2 volts. The positive and negative plates are separated by plates which are neutral and split the voltage to get the voltage between each plate closer to 2 volts. A higher voltage would require more plates between them to bring the voltage back down to 2 volts. Not to mention that car batteries are typically about 12 volts usually a little higher so it is simpler to keep a 12 volt input.
What is material of plates because crossed very fast?
Light that cup Dammit
Can you upload the construction video.with connection between water and generator
If your measurements and my calculations are accurate, you are getting 80-90% efficiency compared to industrial systems:
225 MJ / kg => 64% efficiency (850C industrial)
180-130 MJ / kg => 80-90% efficiency (you)
Where did you get the PWM pls?
Softbank Phone? Are you in Japan?
What Solution are you using?
How the liquid goes ????
does the water stay clen? which means the plates stay clean?
It will if its not reacting to any materials within the generator
Interesting I live on a boat and I'm looking for energy found this video, a dry cell very good.
Looking at to improve the gas mileage Mercedes C230 2006.
You're dreaming.....putting more energy in to get less energy out is a fools gold scenario.
The best use for all of these devices is as an on line on demand gas burner for welding or brazing etc. because you don't need to have stored gas in rented bottles like Oxy/Acc......any other envisaged use is a pure extension of your vivid imagination.
Ian Pearson
Why do you feel that way...?
If it’s because of the cost of
electricity used to make this
gas what if you used either
solar, wind, or hydro to produce
the electricity...?
@@troystutsman1400 It's not the cost of producing gas, it's the electricity you use to produce less energy than you put in.....if you can't understand that then do a test and you will see what the score is. If you are a land based user then any form of electricity is good to go, but as some keep thinking for car mileage improvement it's a no go situation.
hydrogen has no practical use for you there is no free energy and converting electricity to something else to gain anything is just straight up stupid.... your better off adding a electric motor to your car thats connected to your alternator because that way its more efficient and for your boat use induction heater for cooking and electric engine for driving the boat
can it be used as NaOH generator
how can i use it for a car?
Temperatura después de una hora continua?
This is NIKUBA or Not ?
Very Many A!
What is the solution inside?
You should have 2 volt between each plate for better temperatures at this rate you end up boiling the water and adding steam to your hho
Thanks
Can you give me link this detail
What is the material b/w plates (rubber sheet type)
Where i can buy it
Whaf parts you want and where are u located
Y el diagrama o diseño para hacerlo. Materiales y demas cosas
If you want to convince me, tell what electrical power it uses.
Bramborail Frimp it uses car battery 13.5 ish volts
Well, I was asleep at the time, the answer is in the video, power is 337 watts
LPM out ?
25 amps at 13Volts is a lot of watts, can it be done with less power
Yes, look at the Aqua Tune hydrogen fuel system.
hello dear
i have a car
hyundai accent 2007
how many dry cell can i build for it ??
the slices 12 cm * 12 cm
Don't waste your time.......
What type of water you used here???
I think it's distilled water. That you usually pour in car batterys. Ionic purified water.
0 tds distilled water is the best . For hho..
|> |> |> |> |> |> |> |>
|> |> |> |> |> |> |> |>
how many ideots oay tjat bastards to block rhat tech?
I mean ... how many videos you daw all so?
how was your evaluation so in physic?
destilied water eill not sooooo good work ... exept with some tricks in pulsing and so on ...
but that is here not the case ...
so what you all blah around?
take a fucking SEAWATER MIX becazse ... hmmm ... that water that is sooo much as sea have mayby ANY REASON FOR THAT PLANET ...
um ... 800 years of inquisition and witch hunting ... and that what they did so in all countries ...
genetic selection = you arr stupid enough to >believe< that bullshit = may live, ... dont believe and think = bye bye if not corrupt ... iff corrupt ... you all vote it ... or kneel in front ... o.k. back to topic ... use your brain and watch two more and you know....
or tje best: YOU DO AND TRY ...
BECAUSE ALL WHAT ASK SUCH QUESTIONS CANNOT DO ANYTHING IN REAL AND SERIOUS ...
there THOUSANDS of hho videos ... and EVERYBODY neraly tells what he use.
I bet here in a previous video.
biys ... move your asses ... build that abd use it ...
tjat bastards wich blah here bullshit work for that bastards wuch arr respondible that your mum or who ever died on cancer ... and so on. you can fuck them wurh miving your ass and prove thst you are a creature that desearve that planet ... or only a bug for demons that watch rheir mivies, eat their food, work for their miney and power ... and so on ...
and that one wich work for that scum ... there will come a othwr “nürnberger prozesse“ ...
I will vote for deadpunishment ... clean that planet from nadness that life have a chance.
you are all murders .. from life, from soul from all what is good ..
karma dont let itsekf fuck, for ever ...that comes back ...
|> |> |> |> |> |> |> |>
|> |> |> |> |> |> |> |>
Gwen Celtiic
What in the Hell are you talking about...!
Quit smoking your used tampons cause
it’s really screwing up your mind...!
Hi, you buy product?
This dry cell generator fit in your car . work with petrol ?,diesel?,or only hho? ,What is the hho Pressure creat and how to regulate. This is very nice generator you make.Bharat Desai
Dry cells will work with both gas or diesel. They work especially well with diesel motors.
what is the max output litre/minute on this monster ?
If I remember correctly it was over 4 liters per minute
i think the 25amps is mostly just wasting heat and boiling the water.
The water never boiled and the plates never got above 45 c.
عمل رائع
ممكن تعمل علي طمبة رفع مياه
احسنت
Sir can i use a 304 steel plate instead of 316L?
304 plate..water get rusty colour..often to change the water..
Yes! I think my plates are 304 steel.
Gas has to be burnt into another energy. Burnt, only.
What is the black stuff between the plates?
BtotheDtotheF
Those are equal size Rubber gaskets placed in between acrylic panels and stainless steel cells to avoid water solution leakage.
@@abuzarkhan8449 ,,,
Why so high on the volts ? Your going to have a lot of bleed off wasting alit of energy
I separate HHO using two positive connections instead of one negative and one positive..
Just look at the crappy video I made, to find out how.
liters
All things good but not taking film ...movement of camera and tellin new things was so bad too long exactly when you wanted majer the litr per minet .
Man ,,,Where is the "DRY CELL"? I don't understand why you even get up in the morning
rob bob using a lot of power to boil water
Why is it that all you people who make these things have no idea how to talk or explain what you've made?