Art, after 52 years of shooting trap loads with my 3" A5 and cycling every last one by hand I discovered that if you set up for heavy loads and just put a little white lithium grease it cycles fine, just remember to wipe it real clean when you go back to the heavy loads or magnum as the rings will not have enough friction and the barrel will slam back way to hard. As a matter of fact I still have the owner's manual and the way you show for the heavy load setup is exactly what my manual shows.
I follow your instruction on a 1950's Belgian A5 12Ga and the result is perfect every time. I did put one of your rebuild kits in it a few years ago as age and use had taken its toll on the springs. Good kit... great result. Enjoy the beets!
Art, Thanks again for keeping this info on Brownings design out there for all the newbies that get hold of these fine shotguns. The rebuild kit you sold me for my Remington 11 tamed the recoil that was hard on the gun and harder on my shoulder. The original square section recoil spring was near two inches shorter than the new one in your kit. Same with the action spring behind the bolt. I have noticed quite a few you tube videos on the Rhodesian Brownings with the long forend wood and long magazine tube. Also guys are turning A5's into Rhodesian lookalikes. Watching some of them shoot the guns you can see the recoil is severe. Probably due to the recoil spring being sacked or the friction pieces installed wrong or both. We try to spread the word about your rebuild kits and instructional videos as much as possible. Keep up the good work.
Thanks for the videos Art. I have acquired several auto 5's and your tutorials have made it possible for me to make the necessary repairs and maintain them all. Thank you sir for sharing your knowledge.
As a gun smith, this is intuitive for you... Show what it should look like with a close-up on the bevels for high-base and low-base. Go through it slow. Put a gun together in which the rings/springs are for the correct gun, and give us an idea of how much friction there should be.
Art fantastic video. I will like to post a question, need to re blue the two barrels of my Browning Citori year made 1979. It has never being blue before. What will be the best method to do this job. Here in Costa Rica nobody offers the blueing service. Thanks for your time.
Art, I’ve got a question. The real old Auto 5’s have that deal where you have to keep the bolt release pressed to load, but apparently the later ones don’t. Can one swap out the parts to make the old ones be able to load like the newer ones?
I inherited an Auto 5 16GA but the 3 regulation rings are missing. Impossible to find any here. In the USA there are a plethora of them but they do not ship outside the USA. What a pity.
The reason Art is doing this video again, is because so many viewers have already forgotten everything he already taught us in previous vids. They say that the memory is the second thing that goes, the first thing that goes is bladder control :)
Well i guess we need a third video, more confusing than ever, thanks.
Art, after 52 years of shooting trap loads with my 3" A5 and cycling every last one by hand I discovered that if you set up for heavy loads and just put a little white lithium grease it cycles fine, just remember to wipe it real clean when you go back to the heavy loads or magnum as the rings will not have enough friction and the barrel will slam back way to hard. As a matter of fact I still have the owner's manual and the way you show for the heavy load setup is exactly what my manual shows.
I follow your instruction on a 1950's Belgian A5 12Ga and the result is perfect every time. I did put one of your rebuild kits in it a few years ago as age and use had taken its toll on the springs. Good kit... great result.
Enjoy the beets!
Thanks for covering this yet again Art! Some, however, might need an additional video in the future, lol!
Art, Thanks again for keeping this info on Brownings design out there for all the newbies that get hold of these fine shotguns.
The rebuild kit you sold me for my Remington 11 tamed the recoil that was hard on the gun and harder on my shoulder. The original square section recoil spring was near two inches shorter than the new one in your kit. Same with the action spring behind the bolt.
I have noticed quite a few you tube videos on the Rhodesian Brownings with the long forend wood and long magazine tube. Also guys are turning A5's into Rhodesian lookalikes. Watching some of them shoot the guns you can see the recoil is severe. Probably due to the recoil spring being sacked or the friction pieces installed wrong or both. We try to spread the word about your rebuild kits and instructional videos as much as possible. Keep up the good work.
Thanks for the videos Art. I have acquired several auto 5's and your tutorials have made it possible for me to make the necessary repairs and maintain them all. Thank you sir for sharing your knowledge.
Great vid Art, as always...geez, gotta get my A512ga ('57) & my dads' A516ga ('47) over there for servicing ~
As a gun smith, this is intuitive for you... Show what it should look like with a close-up on the bevels for high-base and low-base. Go through it slow. Put a gun together in which the rings/springs are for the correct gun, and give us an idea of how much friction there should be.
Fantastic video sir.
Please keep making new videos.
AMEN!!!
Art fantastic video. I will like to post a question, need to re blue the two barrels of my Browning Citori year made 1979. It has never being blue before. What will be the best method to do this job. Here in Costa Rica nobody offers the blueing service. Thanks for your time.
Thank you Art.
Art,
I’ve got a question. The real old Auto 5’s have that deal where you have to keep the bolt release pressed to load, but apparently the later ones don’t.
Can one swap out the parts to make the old ones be able to load like the newer ones?
Very knowledgeable its great
Great
Great job thanks for sharing your knowledge with us 👍🏼
What is the name of your website?
Sabe si las estrellas marcadas en el cañón tienen la misma equivalencia a las estrellas españolas
Always buy my spring kits from Art. He sends you the diagrams!
Brother, Is 1oz loads considered light and 1&1/8oz heavy for a 1987 Sweet 16? Thanks!
Sir , is there any Belgium made auto 5 , 12G made of aluminum action ?
Is this how the Remington Model 11 is also set up?
I wonder if the same instructions pertain to a Remington Model 11 ??
Yes
I inherited an Auto 5 16GA but the 3 regulation rings are missing. Impossible to find any here.
In the USA there are a plethora of them but they do not ship outside the USA. What a pity.
All parts missing or just a steel ring (1:16 video time)?
@@bartlomiejpiszczek3987 Unfortunately the 3 rings are missing
How do I get the A5 rebuild kits
Check out our websie www.artsgunshop.com.
Ummmmm? At one stage you forgot what you did 2 seconds beforehand? I hope they don't give you live ammo to play with? 😱🤣
The reason Art is doing this video again, is because so many viewers have already forgotten everything he already taught us in previous vids. They say that the memory is the second thing that goes, the first thing that goes is bladder control :)
Jesus, this guy reminds me of Joe Biden. Give it up, Art..time to retire.
Were you born an asshole?