Thank you for making this video. I learned more in your 11 minutes than in my 3 hour shop class . Actually 2.5 hours with breaks ! Also hard to learn with 6 guys and instructor crowded around machine. Only my 2nd class on the Doosan. I didn’t know about that eye sensor. We did touch off holding a scrap of paper between the workpiece and cutting tool. It’s hard to get the feel of the pressure to hold the paper with how close to set the tool . It will take experience. Already like .0006. off just with set up by feel would blow a job with tight tolerance . Nice to know those eyes are out there to take the guesswork out of the equation. Thanks again for making a video that is clear and you can actually see the control. You are very professional in your explanation and calm even presentation. Plus good example with proper ppe eye protection and work uniform.
You are most welcome. My goal was to give a clear understanding on this machine setup. So many machines are different and having a video like this really helps. For more visits like this check out this page czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
Thanks for this video bro. I learned a lot. I started in this trade in January and have been loving every minute of it and I’m running this same machine every day. I appreciate the teaching bro. I’ll be honest when you dropped the tool presetter then closed the door and then referenced the machine I tensed up a little lol 😂
Your welcome for the video. I enjoy making them fit others to learn from. If you want to see more of them you can see them here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
Great video..I saw you dont publique new videos long time ago,I dont understand why. my english is realy poor but I really thank your way to explain every single move of this process. thank you for your time. hope you piblique one to know how to make a program on this kind of lathes.
Definitely one of the most comprehensive and explanatory videos on YT👍. Thank you for sharing this👌💛! This has made me definitely closer from my #Haas'ish understanding to #Fanuc'ish mastery if I can say so.
It's very easy for someone to understand what's happening during a setup, not everyone has this understanding especially if they are wanting to learn. So making videos like these really helps others and that why I make them. If you want to see more like this check out czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
How old is this machine? Is there no canned cycle for tool setting? I see you manually moving the tool tip around and selecting the quadrants using numbers instead of visuals.
This machine is from 2004 and is still very much useful and week continue to be if it's taken care of. That's why I made the video to help others when setting it up. Also, yes there are many canned cycles that run on this machine. I have videos of them here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
So this machine will have geometry but not tool height. Some machines do have this ability but is mainly used for conversation programming. Check out more here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
So when you set up that part again, because you save the program after the setup in the usb, will the tool offsets and geometry all be the same when you load it back up ? As in you won't have to touch off any tools ?
Well you can out put the offsets as well as the program to the USB. I've never had the opportunity to really use this feature, as once you pull a tool out of the turret, the tool length is not going to be exactly the same next time around. So loading the saved offsets is kinda useless.
Good news if you just setup the jaws and don't remove the tools your in good shape. Also, even if you remove the tools but load them in the same position you could dial then back in as long as they are pushed back against the stop or all the way into the turret position. It's still recommended that you touch them off again. To see more tips and Setup videos check them out here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
There is a way using a graph, but you will have to lock the machine's axis with I believe code M17 and then run your program in auto mode. The spindle will run, and the turret will index, but X and Z will not move. On the graph, you'll see feed and rapid lines. Once ready to run unlock your axis with M18
Fanuc is a plugin and cycle start on the CF card, the reason fanuc uses a CF card is because it is more stable and faster, i have used both machines and the cf card method is superior, fanuc has not yet developed much into usb. and there is no need.
I have an older Daewoo Puma without the "tool eye". Setup is so much easier. I just have my T0101 always set to 3.000. Then I face the part and work shift my coordinates to get T101 position to 3.000. If my tools were already set up off of that face then I am done. If not I use a gauge block and input my Z offsets for each tool. Diameters I have to turn and measure. This just seems more complicated for some reason,
@@matt23727 agreed, you can access tool offsets, (X and Z) alter rad's, alter workshift all in the offset page. I found it quite simple as an apprentice to pick up
Yeah that's the real issue with Fanuc. It isn't that they're "harder" to use, it's the lack of consistency. Going from a mid 90s Haas to a brand new one, it really isn't all that different.
Buenas tardes como está. Saludos desde Bogotá Colombia. Será que me puedes enviar todos los ciclos de ese torno Doosan ciclos de ranura de roscado desbaste en fin todo todos los ciclos de taladrado o si me puedes enviar programas con los códigos del encabezado o micelanios gracias
This is my job 9 years ago other day One coworker know me cough a lot he gave me cough medicine but he lie he gave me the mental medicine I was not remember a lot of words and the boss go play to me then I quit job
Thank you for making this video. I learned more in your 11 minutes than in my 3 hour shop class . Actually 2.5 hours with breaks ! Also hard to learn with 6 guys and instructor crowded around machine. Only my 2nd class on the Doosan. I didn’t know about that eye sensor. We did touch off holding a scrap of paper between the workpiece and cutting tool. It’s hard to get the feel of the pressure to hold the paper with how close to set the tool . It will take experience. Already like .0006. off just with set up by feel would blow a job with tight tolerance . Nice to know those eyes are out there to take the guesswork out of the equation. Thanks again for making a video that is clear and you can actually see the control. You are very professional in your explanation and calm even presentation. Plus good example with proper ppe eye protection and work uniform.
You are most welcome. My goal was to give a clear understanding on this machine setup. So many machines are different and having a video like this really helps. For more visits like this check out this page
czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
Excellent video! I just purchased a used Fanuc controlled lathe and this video has been very helpful in getting up to speed with setup and operation.
Thanks for this video bro. I learned a lot. I started in this trade in January and have been loving every minute of it and I’m running this same machine every day. I appreciate the teaching bro. I’ll be honest when you dropped the tool presetter then closed the door and then referenced the machine I tensed up a little lol 😂
Instablaster
Your welcome for the video. I enjoy making them fit others to learn from. If you want to see more of them you can see them here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
Great video..I saw you dont publique new videos long time ago,I dont understand why. my english is realy poor but I really thank your way to explain every single move of this process. thank you for your time. hope you piblique one to know how to make a program on this kind of lathes.
Definitely one of the most comprehensive and explanatory videos on YT👍. Thank you for sharing this👌💛! This has made me definitely closer from my #Haas'ish understanding to #Fanuc'ish mastery if I can say so.
It's very easy for someone to understand what's happening during a setup, not everyone has this understanding especially if they are wanting to learn. So making videos like these really helps others and that why I make them. If you want to see more like this check out
czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
Thanks so much... From Greece (Here we call Tool Setter)
@Hamza Kashton cringe
Welcome
MTS representing!
What about the workshift settings?
great job. write some programs, facing, od rough, drill, tap, od finish
Great news i have lots of training and programming videos here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
Sir zoom nothing is seen which key are u using to operate
What year is this Doosan Lynx 220?
How old is this machine? Is there no canned cycle for tool setting? I see you manually moving the tool tip around and selecting the quadrants using numbers instead of visuals.
This machine is from 2004 and is still very much useful and week continue to be if it's taken care of. That's why I made the video to help others when setting it up. Also, yes there are many canned cycles that run on this machine. I have videos of them here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
May i ask cost of machine like that, want have some idea. Thanks.
On our pumas they say q set
Hello sir,
Where do you write the tool high?
Page?
So this machine will have geometry but not tool height. Some machines do have this ability but is mainly used for conversation programming. Check out more here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
buenas tardes cual es el codigo para descativar la alarma de la puerta gracias
en la caja que trae tiene los codigos pegados,donde estoy trabajando aurita es solo haas que tenemos y ganesh
Well done. Thank you for education. From Russia with frendship.
Your welcome here's more czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
Hallo bro . Please review GSK
hehe you wanted to say on a Haas lathe XD
So when you set up that part again, because you save the program after the setup in the usb, will the tool offsets and geometry all be the same when you load it back up ? As in you won't have to touch off any tools ?
No. You have to touch off everything again
Always have to touch off the tools
Well you can out put the offsets as well as the program to the USB. I've never had the opportunity to really use this feature, as once you pull a tool out of the turret, the tool length is not going to be exactly the same next time around. So loading the saved offsets is kinda useless.
Good news if you just setup the jaws and don't remove the tools your in good shape. Also, even if you remove the tools but load them in the same position you could dial then back in as long as they are pushed back against the stop or all the way into the turret position. It's still recommended that you touch them off again. To see more tips and Setup videos check them out here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
Where is your country sir??
Bro, is thier any option to check graph before run the job?
There is a way using a graph, but you will have to lock the machine's axis with I believe code M17 and then run your program in auto mode. The spindle will run, and the turret will index, but X and Z will not move. On the graph, you'll see feed and rapid lines. Once ready to run unlock your axis with M18
They use tool eye on mazak
HAAS is so much easier to upload and download a program from the USB, but I guess that's FANUC.
Fanuc is a plugin and cycle start on the CF card, the reason fanuc uses a CF card is because it is more stable and faster, i have used both machines and the cf card method is superior, fanuc has not yet developed much into usb. and there is no need.
Good job dude! How do you activate de Y axis?
So this machine does not have a Y axis but it can ask do some cool stuff
Here is a link to more videos like this
czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
I have an older Daewoo Puma without the "tool eye". Setup is so much easier. I just have my T0101 always set to 3.000. Then I face the part and work shift my coordinates to get T101 position to 3.000. If my tools were already set up off of that face then I am done. If not I use a gauge block and input my Z offsets for each tool. Diameters I have to turn and measure. This just seems more complicated for some reason,
Because you've never used it.
A tool probe is 1000 times better
@@matt23727 agreed, you can access tool offsets, (X and Z) alter rad's, alter workshift all in the offset page. I found it quite simple as an apprentice to pick up
This is why I hate Fanuc. Every single controller is a world apart, even in the same year product run. My doosan lynx controller is totally different.
Yeah that's the real issue with Fanuc. It isn't that they're "harder" to use, it's the lack of consistency. Going from a mid 90s Haas to a brand new one, it really isn't all that different.
Check newest doosans with fanuc xD or newly DN solutions, its pre chaos and lagg :/
Cómo puedo programar un ciclo de taladrado profundo
You want to use a G83 canned cycles. Learn more about them here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
Buenas tardes como está. Saludos desde Bogotá Colombia. Será que me puedes enviar todos los ciclos de ese torno Doosan ciclos de ranura de roscado desbaste en fin todo todos los ciclos de taladrado o si me puedes enviar programas con los códigos del encabezado o micelanios gracias
The best thing to do if you would like to see programming videos is to check them out here czcams.com/channels/awMg1dcdGS7K9aBIG2RGGw.html
Good news, I have a lot of videos with more of the info you are seeking.
Cuando está taladrando sale una alarma algo de hidráulica
La alarma tendrá algo que ver con sus niveles de aceite. Asegúrese de que su máquina esté completa y vuelva a intentarlo.
This is my job 9 years ago other day One coworker know me cough a lot he gave me cough medicine but he lie he gave me the mental medicine I was not remember a lot of words and the boss go play to me then I quit job
You didn't really say anything about homing. You pushed buttons without saying anything.
Sorry about that. I did miss this. I did touch base on these in my other programs.
I añmps forgot all about cnC lathes,, besides ,I'm making more money on construction.
And this is why I hate Fanuc!!!........so many key strokes and different pages and arrow across to do ...
And the award for the worst camera guy goes toooooo.
I hate fanuc😢