Repair Dremel 3000 at home .
Vložit
- čas přidán 23. 07. 2024
- Self repair of power tools is an interesting job it saves time and gives knowledge about the working principles of the tool, it also save money. Here I have demonstrated my defunct dremel which was lying useless. I have been to the repairing shop but repairing charges was high so I thought to repair myself and I did it. there was zero expenditure. Any one can do it. please watch the video from beginning to end. Thanks.
If you like this video please like,share and subscribe. Stay tuned for more videos - Jak na to + styl
3 years after this video was uploaded, i just fixed my dremel by following your instructions, thanks man!
Four years later u r still helping people. Thanks man.
Followed exactly your video, the problem was as you said, in the stator circuit. Trimmed the wire and put it back, now it's working again. I would never have figured it out on my own. Thanks very much, you have saved me time and money.
Saved me a lot of money here, my old 3000 is alive again! thanks
Good morning, friend I am Brazilian living in Portugal I have a Dremel 3000 with little use today I was using it and it stopped working, I contacted the assistance and I was informed that I would spend about $ 60.00, I went to do a search on the yotube and found his video thank you very much and congratulations I managed to fix my dremel without difficulty and without spending any money thanks. Sorry the English translator kkk
You're awesome!!! saved my Dremel !!!! That exact same issue with the stator.
Just one tip for anyone with the same problem as me: depending on which of the two loose contacts is the problem, you may not be able to unwind a single turn to reconnect the wire. Just solder a stub of wire in case you have the issue on the wrong end of the coil (you won't be able to unwind it).
I wish I had read this comment before trying to unroll the inner thread, I cut it trying, but noticed that on the other side the innermost turn was slightly separated from the others, I pulled it and bingo! It was precisely the strand that had been cut, I think from factory leaves that strand separated to indicate that it is the first round.
What thickness wire did you use?
Excellent video - and it worked! Dremel is alive again!
Wonderful stuff, exactly what the Dremel needed! Thank you!
Great video. Very informative without any blah blah blah stories and stuff. I like how you made the continuity tester as well, ingenious!
Also, thanks from myself. My Dremel 3000 failed last week. Followed your dis-assembly procedure and diagnostics and found the exact same problem! It's now working fine. Excellent work.
OMG this video has saved my Dremel, thank you so much!!!
Thank you so much for this. My dremel stoped and I fixed it right away with your instructions.
Had exactly the same problem with my Dremel 3000. Excellent instructions!
Solved, thanks! Greetings from Argentina.
This repair works!!! Thank you for posting the vid, I have been searching long for a solution and this was the only repair that worked. Thanks a million!!!
Mine didn't work anymore about one month ago. As the stator winding had an on/off broken wire I thought it was something on the small circuit board, or the switch. Couldn't find anything wrong. Today I saw your video and checked the Dremel again. It's back in operation. Thanks a lot! :)
A well thought out description of all shown parts . Fixed mine , thanks again . Keith.
Thanks a lot! That's the last thing I would've thought of. I was already going to order a new power switch when I stumbled upon your video.
Gracias, acabo reparar el de mi hijo en 10 minutos. Muchas gracias.
Thanks. Less than 10 minutes and I have repared muy son's DREMEL 3000. Many thanks from Buenos Aires, Argentina
Thank you, problem found (armature wire off and visual) and Dremel running again, saved me a fair amount of money.
Yep, broken wire, now all fixed. Thanks for putting up the video. Perfect 🙌
Well done! I will try and fix mine now as Dremel said too old to repair
Grazie a questo tutorial sono riuscito a riparare il mio amato dremel 3000 grande!
Thanks so much!
finally after years I have my working dremel again
infinitely thank you
Exactly the same fault on mine. Good save. Cheers.
Fixed my Dremel thank you, evidently it is a weak point common to this model
Thank you, thank you, thank you! … exact same problem with my Dremel 3000, fixed it using your easy instructions! … it must be the Achilles heels of the 3000 series. But what an easy fix, cheers again!
Not an electronic whizz by any means. This is my second 3000, the first one went the same way without a whole lot of use, but as it was for work I put it a new one through my business. When this one stopped in exactly the same way I thought I'd look at the You Tube oracle as I was hacked off with using this similarly infrequently. As the last poster said, I cannot believe i've fixed it. turned it on and expected a spark but was 'shocked' but in a good way. Thanks so much for the step by step.
Thanks for this. It was the first Dremel repair video I looked at and showed exactly the problem I had with mine; broken connection in the stator coil.
From reading the comments here it seems like a common issue.
Thanks again.
Acabo de seguir tu tutorial con mi Dremel 3000 que dejó de funcionar cuando lo utilizaba como router. No sabes cuánto te agradezco que compartieras cómo componerlo, sólo me tomó 15 minutos después de ver tu video y ya está de vuelta trabajando. MUCHAS GRACIAS.
Thank you for this fantastic DIY! You just saved me a ton of time and money!
Set about mine this morning and had it fixed within half hour, seems to be a common problem, thanks again for your very detailed video.🏴
Too commom, i will never buy original dremel again
Thank you! You saved me time and money. I was able to determine that I had a bad stator. I not able to repair it but I did find a replacement part. My Demel 395 has lasted through 25 years of abuse. Made in the USA and well worth repairing.
Thank You for making this video, You make so simple that everyone can follow. I just repaired mines and it's working fine. Thank Again.
This video saved me a lot of time, money, and headache, thank you so much for posting! :-)
Thank you for your video! My Dremel 3000 had exactly the same problem.
Thank you , 10 mins and mine is now fixed. Long live the dremel 3000 !
Had the same Problem with a dremel 300, European model.
This Video helped alot!
Thanks !
Thanks, mine packed up for no reason will strip it down tomorrow. Very informative video, thanks again.
Awesome fix. Worked brilliantly. Thanks!
Thank you very much for making this video! This video helped me fixing my Dremel!
Simple and very explanatory video, solved my problem, thank you my friend, a hug here from Brazil!
thanks to your video I was able to solve my problem. thanks!!
Brilliant video. We watched a different video with similar instructions but less detailed and we nearly gave up after trying to reattach the wires and still no luck. Its only through this video that we found out the previous fix hadn't worked because of the layer over the wire that needed to be scraped off. Thankyou!
You saved my Dremel, thank you.
Thank you so much! Now I won't have to travel really far and pay an exorbitant fee to get it fixed. My Dremel works again.
I can't nelieve i just fixed my Dremel....shaft was stuck but motor wanted to turn. Your video still helped...yay
THANK YOU THANK YOU THANK YOU!😃
Even a Dis-Electric as myself could fix his machine 👍🏼
(I usually HATE video tutorials. Yours is JUST RIGHT! 😊👍🏼)
stefan in Germany
Muito obrigado, não sabia o que fazer, já estava pensando que iria por a dremel no lixo, foi salva pela sua ajuda. Obrigado.
Excellent, repaired my Dremel 3000
Thank you, thank you, thank you. That was it. My Dremel lives again.
I watched this and found out how to take it apart. Found out my problem was tons of dog hair and nail dust! Blew it all out and worked like new! My wife is a dog groomer. You have to open it up to get it all out to make it work. This is definitely another possibility. Thanks for the video!
Dude! Thanks for this video. The bulb test was a great tip
Epic video, saved my day. I can’t thank you enough 🙏
Awsome, Thank you Dude. Greetings from Turkey.
The video was awesome, fixed it perfectly! Many thanks
Thanks for this, had the exact same problem, solved in 10min.
It was very helpful, my Dremel works again, thank you!
Thanks fr watching bro.
Thank you for posting this video, i just fixed mine because of this. Good job, Man!
Thanks for this tip. Fixed mine exactly like showed on the video. Wish you the best! :)
This was so helpful!! Thank you thank you!!
Great video, explains really well
Exatamente o problema da minha. Vídeo caiu como uma luva! Obrigado.
Thanks so much! You saved my Dremel!
Nice video! Other videos on this tool address only the brushes. This one might actually deal with the problem affecting my own Dremmel. Thanks!
thank you for the video it saved my dremel
thanks a lot. Same trouble (coil broken), solved thanks to your guide !!!!
burned dremel problem fixed! thanks bro!
Thank you for the video ..After 2years lying in the toolbox not working, and me wanting to throw it away , it,s working again , all the time i thought it was the speed controller broken .
just repaired mine! Thank you.
thanks for your lesson it was great it was so easy for use to understand the way you specify l like
Mine had the exact same fault after fairly light use, I repaired it the exact same way and now it works again. Thanks Young DIY. Bad design Dremel....!
Thanks bro.
Thank you. My dremel 3000 had the same problem.
Thank you, from Germany! 👍
Yep, had same problem, fixed now. Many thanks
Awesome, thank you, saved another dremel good man!
Watching your video I solved my problem. Tks!!
A minha parou de funcionar e desaparafusei toda, retirei os carvões, e acabo de ver no vídeo que faltou o adesivo...rs... não quis cortar, descolar, achando que não abrira por faltar algo... o vídeo é espetacular. Obrigado!
right on. Thanks. Just a video editing tip, when the camera is close up on something and is less sharp, slow down the speed frames so we can follow the details better.
Thanks! Very helpful video and problem solved
Nice work!!!
You made my day!!! In my case, the broken wire came from the core of the winding (the 1st turn) so I couldn't unwind one turn. Instead, I managed to un-enamel the last millimeters and soldered a bare wire. A warm hug from Argentina!
Off-topic: I feel empathy towards electronic components! I suffer when I see them suffer. So, when I saw you applying 9 volts to a white LED I felt my heart was about to explode! ;-) Please don't do that for a long time without a series resistor (from my own experience...)
Hola, a mi me paso lo mismo me parece. cuando le estaba sacando una vuelta se me corto el hilo de cobre. Como lo solucionaste??
@@danielrperez5778 - It's a BIG Coil Wire Gauge. He's only using it to complete a circuit... It won't harm anything!
@@watusilifestyle9335 Perdón, recién veo tu pregunta. En mi caso, tras cortarse en esa horqueta que hace la conexión, el alambre quedaba corto, y no podía desenrollar 1 vuelta porque venía desde abajo del bobinado, y tampoco podía estirarlo. Pero no es que lo había perdido. No me digas que se te cortó justo donde sale del bobinado! Si es así, más vale que sea en el final, no en el principio, o tendrás que desbobinar todo.
Very thorough and clear..just have to take mine apart😁👍
continuity check failed for one of the stator coils, wire looked ok, i pulled a little harder and it came off, unwinded 1 turn and clipped back, working back again
seriously, continuity check is a must, thos little metal clips can cut the wire and keep it in place, so visul check won't do.
thanks for the video, my dremel is back to work now
Thanks, I was able repair my handy dandy Dremel .... and saved money by not buying a new one
You made my day! Thank you! 💯
solved the same problem, saved my xmas presents, thx!
The internals are very different from my 3000 that I recently purchased. Very good video.
Worked a treat, thanks!
Whooooo. My dremel works again! Thanks!
Super...Thanks from Turkey. My problem is fixed.
thank you very much, helped me a lot. had the exact same mistake
Brilliant thanks for the video just did that and fixed my dremel
thank you for this video. I was able to fix my 3000 using the intel
Thanks man, you saved me!
Muito obrigado!!!!
Vc salvou minha dremel que estava quase indo pro lixo!!!
Ganhou inscrito e like.
👏👏👏👏👏👏👏🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷
You are amazing! Thanks
Thank you ! Problem Fixed.
I was just about to buy a Dremel 4000 because my 3000 has some issues!, I'll be taking it apart this weekend
Thanks mate! Same problem Dremel Multi.