He's a "Carpenter not an Actor" How quick we are to criticise, you film yourself for 45 minutes and see how many times you repeat yourself, I found the video to be extremely informative and well filmed & edited, thanks to all involved
I hired a 2KW router with worktop jig, bought a set of joining bolts along with a brand new 1/2" router cutter and followed this video to the letter taking my time to double check everything and the results were perfect. Excellent video
You Sir are a steely eyed kitchen fitter! I feel very comfortable with your explanations and tips, you make it sound so easy. If I were 50 years younger I would consider myself really fortunate to be your apprentice. Thank you so much.
was looking for a heel toe vid for some French doors, come across this and found myself watching til the end. Excellent demo, BASICALLY a true pro. Keep it up lads
A nice clean job done with ease. I myself am a chippy, but never seem to just go from start to finish without any problems. You can never know to much and will always learn new tricks. good vid
Have just installed 4 x super large mango bench tops we cut and thicknessed from a 102 yr old tree here in Far North Queensland Australia. The laptop's been playing on one side of the new kitchen with you excellent video while we cut and routered on the other side. So the last two days it's been 'watch'...pause...measure...'watch'...pause...measure again... 'cut & router'....'watch'...pause...etc. Its a shame that we had to pay $350 for a jig we'll likely to only have to use once but I have to tell you, your advice and commentary has been mint and the plumber arrives tomorrow to connect the stove, sink and oven into our fabulously fitted bench tops. Only comment I'd suggest is to let everyone know that your excellent method works equally well for timber slab tops as it does for your laminates in the vid. Fan-friggin-tastic as we say here in Oz - many thanks - Shaun
Thanks for a very informative video, when I first seen it was on for 43 mins I thought "how the heck can he talk about mitring a worktop for that long" but the time just flew in, very well explained and hopefully I will be putting your shared knowledge into practice, thumbs up for your camera man too 👍
Been watching instructional videos for years doing my own home DIY, but by far, this is the clearest and simplest I've seen with so much detail and real tradesman's eye and tips. I know this has all already been said in the other comments here, but thank you very much, subscribed.
Hey Tommy, enjoy watching as you really give a lot of detail, I use a "Ratchet" spanner for tightening the dog bolts, I find it much quicker and easy on the wrists as we're not getting younger mate! It's good that you show the work in real time too cause most clients don't realize the work ,time and knowledge behind negotiating the peanuts Tradesmen earn!
I always love Dave's videos, you can just tell that he's done it 100s of times before & of all the CZcams videos on Worktop Mason mitres this is by far the best. Thanks Dave & Tommy, please do more videos Dave.
The guide bush runs in the jig with a bit of slack as the groove in the jig is normally about 8-10mm wider than the guide bush, so its always best to make the first cuts on the side of the jig groove away from the joint, and then make the final pass on the side of the jig closest to the joint, makes a much neater cut. I've never used PVA, always used clear varnish on the raw chipboard in the joint to seal it against water ingress, 3 or 4 coats, then squeeze in some colorfill to finish.
Just done my first worktop mitre job. Replacing tops in a u shaped kitchen. Nightmare! But thanks to watching Dave explain it and having a practise run beforehand it went pretty damn well! Thank you Dave. Keep the bids coming.
When cutting from the back of a wood worktop you need to clamp another board under your cut line nice and tight, otherwise you risk blowing out the wood fibres as you plunge through it resulting in ugly tearout on the visible surface of your worktop. Generally its better to cut with the entire worktop supported on a scrap board than hanging on saw horses as your offcut could snap off under its own weight before the last cut and make a right balls of the cut. Also, its pretty standard to use a biscuit cutter to place some mating biscuits when joining to solve that alignment issue when bolting.
Bloody brilliant. Can't find anyone to do the worktops in our kitchen and this has given me the confidence to give it a go. Will probably do a few dozens mitres on the old ones first!
Great video!...clear guidance....I was cringing when the hammer was being used directly on worktop ( always use a block )....to flush the joint....video shows how long and tedious it is to fit worktops....don't just happen....nice one....
Absolutely brilliant - very clear with explanation. This really helped me a lot. I have done one worktop before and watched this again as a reminder for another one I have to do.Thank you very much.
Excuse my language but Fucking brilliant video. I've been in the kitchen trade as a designer for over twenty years and I've been told how its done but never really understood. Just watched this and it makes perfect sense now. Genius, thanks. Right, what were gonna do now (ha ha ha) is watch a few more.
Great explanation and demonstration, extremely clear video, first thing I was thinking watching that spanner work was that, like Max said, I'd use a ratchet ring spanner to run those nuts down, it would be a lot quicker and easier than an open end spanner, especially if you're doing joints often.
You can score the worktop with the router, then jigsaw the rest out leaving the jig in place. Leave a couple of mm with the jigsaw. Then just clean it up, with one full depth pass of the router. It saves your router bits and router from an early grave.
A couple of notes - A small gap between wall and boards gives you some breathing room if there is movement in house and or require a very slight adjust from error. Probably try and use a 0.7 - 0.9 mechanical pencil to keep lines sharp .. the fat lines from blunt pencils make for bad errors. Great video ..
Tommy thankyou very much for posting. Much appreciated to folks whom take the time to educate the rest of us. As a Yorkshireman saving money always appeals. Many thanks. Lewis
Two tips for first timers. When cutting the joint with the template, always release the router cutter upwards before lifting the machine out of the slot otherwise you will invariably nick the template with the cutter destroying the machined edge. To tighten up the bolts, get a 10mm ratchet spanner, one from the Halfords professional range is best as it has a very fine ratchet. Makes doing up the bolts much quicker. Also. Bushboard do a joint compound especially for this job in matching colours.
Thanks so much for this excellent and professional video. Well planned and good photography. I have to buy a router yeah? I will now watch you cutting the sink hole. The last time I cut one upside down and lifted it up on my back to install, it broke. That's the last time I remember crying. So hopefully this time I can put it in position, and then cut the hole from the top. My biggest problem seems to be fitting the sink and drainer in between the support bars of the base units. Thankz smuchly and God Bless.
I'm Dave not Iestyn, he's my son lol thank you Tommy for taking the time to put this video together. I'm a time served Carpenter, but I never do many Kitchen butt and scribe work?? this has given me ease of mind as I lost the instructions for my Trend jig. Can't fault you mate!!
This is so well done. Logically explained with little tips. I would love to work with this guy for 12 months. I could learn so much. Would a ratchet 10mmm spanner make life easier ? Also, is it practical to glue softwood jaws onto the C clamps to save fiddling with cardboard ?
Hi, thanks for the informative video. Two questions: Why not use the jig's sliding gauge to determine the width of cut in the female?? Also, when marking the male joint, why not put the male end on top of the female cut top, supported at one end, then just scribe from beneath the worktop? Cheers Dave, Tony
Many thanks for this video. Watched it 3 times then hired a router and template (HSS hire bundle), had a practice on an old piece of worktop and then went for it. Really pleased with the results. One question. Why no biscuits in the joint?
Excellent video....The guy is very good at his trade and at making videos Perfect! Help get rid of the Cowboys do you're research and use one of the good guys like this one...
Tommy, blinding explanation! Love the banter - you can say 'basically' as much as you like as far as I am concerned! My kitchen worktops are solid wood which were in the house when we bought it. A 3m length is over £400! I have enough remaining from downsizing the tops to make up what I need by joining with straight joints. A good router will cost approx £300 (for me as a competent DIYer for 40yrs) so a router and jig it is. Please could you tell me what the make and part number is of the router you are using in the video please. I like the ease of locking and adjusting the depth. Judging as an engineer, it looks to be well engineered. Cheers, Jon
Just a thought. Once ur setup ... why not go into the jig slot and remove most of that material with a jig saw. Would save a lot of time and wear and tare on the cutter bit.
Wouldn't make sense to cut the bulk of the material out with a jigsaw after you have your jig mounted to prevent any laminate chip out. Nice job ... I'm just thinking of cutter pull with the heavy cut. Nice video. Thanks.
Excellent video, thanks! However I can't help but notice how the sink bowl looks to be in a terrible position to use every day!! (half way in the corner of the work top) Home owners decision I'm sure, but it just looks very awkward to me.
My only criticism with the video is the lack of hearing protection. I've spent years attached to routers and they're bloody loud. Other than that, I can't fault it, cracking vid
Thank you, I found this a very helpful guide to cutting in a worktop. I was able to follow the basic principles and successfully mitre together two worktops, twice for different rooms. I did have some issue with the visible edges on the surfaces chipping slightly where the cutter went along, on both the top surface and (more seriously) on the front profile edge, despite all my efforts to prevent this. The only other thing I would suggest is to not drop the router down too much on each cutting pass because this increases the chance of the router going off track as it struggles to cut too much material. Top helpful video though
Nearly 1.5 million views, as I type. Just hope this guy is getting some £$love£$. Artisan. My DW625EK only gets the dust blown off the box 3 or 4 times a year.
Really useful to watch if you are having new worktops fitted, even if your not going to attempt it yourself, you can see how its done and check the workman are doing it correct. ta
He's a "Carpenter not an Actor" How quick we are to criticise, you film yourself for 45 minutes and see how many times you repeat yourself, I found the video to be extremely informative and well filmed & edited, thanks to all involved
I hired a 2KW router with worktop jig, bought a set of joining bolts along with a brand new 1/2" router cutter and followed this video to the letter taking my time to double check everything and the results were perfect. Excellent video
You Sir are a steely eyed kitchen fitter! I feel very comfortable with your explanations and tips, you make it sound so easy. If I were 50 years younger I would consider myself really fortunate to be your apprentice. Thank you so much.
was looking for a heel toe vid for some French doors, come across this and found myself watching til the end. Excellent demo, BASICALLY a true pro. Keep it up lads
A nice clean job done with ease. I myself am a chippy, but never seem to just go from start to finish without any problems.
You can never know to much and will always learn new tricks. good vid
Have just installed 4 x super large mango bench tops we cut and thicknessed from a 102 yr old tree here in Far North Queensland Australia. The laptop's been playing on one side of the new kitchen with you excellent video while we cut and routered on the other side. So the last two days it's been 'watch'...pause...measure...'watch'...pause...measure again... 'cut & router'....'watch'...pause...etc. Its a shame that we had to pay $350 for a jig we'll likely to only have to use once but I have to tell you, your advice and commentary has been mint and the plumber arrives tomorrow to connect the stove, sink and oven into our fabulously fitted bench tops. Only comment I'd suggest is to let everyone know that your excellent method works equally well for timber slab tops as it does for your laminates in the vid. Fan-friggin-tastic as we say here in Oz - many thanks - Shaun
This is the best and most clearly explained worktop jig video on CZcams. Thanks.
Thanks for a very informative video, when I first seen it was on for 43 mins I thought "how the heck can he talk about mitring a worktop for that long" but the time just flew in, very well explained and hopefully I will be putting your shared knowledge into practice, thumbs up for your camera man too 👍
Been watching instructional videos for years doing my own home DIY, but by far, this is the clearest and simplest I've seen with so much detail and real tradesman's eye and tips. I know this has all already been said in the other comments here, but thank you very much, subscribed.
Hey Tommy, enjoy watching as you really give a lot of detail, I use a "Ratchet" spanner for tightening the dog bolts, I find it much quicker and easy on the wrists as we're not getting younger mate! It's good that you show the work in real time too cause most clients don't realize the work ,time and knowledge behind negotiating the peanuts Tradesmen earn!
I always love Dave's videos, you can just tell that he's done it 100s of times before & of all the CZcams videos on Worktop Mason mitres this is by far the best.
Thanks Dave & Tommy, please do more videos Dave.
The guide bush runs in the jig with a bit of slack as the groove in the jig is normally about 8-10mm wider than the guide bush, so its always best to make the first cuts on the side of the jig groove away from the joint, and then make the final pass on the side of the jig closest to the joint, makes a much neater cut. I've never used PVA, always used clear varnish on the raw chipboard in the joint to seal it against water ingress, 3 or 4 coats, then squeeze in some colorfill to finish.
Just done my first worktop mitre job. Replacing tops in a u shaped kitchen. Nightmare! But thanks to watching Dave explain it and having a practise run beforehand it went pretty damn well! Thank you Dave. Keep the bids coming.
When cutting from the back of a wood worktop you need to clamp another board under your cut line nice and tight, otherwise you risk blowing out the wood fibres as you plunge through it resulting in ugly tearout on the visible surface of your worktop. Generally its better to cut with the entire worktop supported on a scrap board than hanging on saw horses as your offcut could snap off under its own weight before the last cut and make a right balls of the cut. Also, its pretty standard to use a biscuit cutter to place some mating biscuits when joining to solve that alignment issue when bolting.
Bloody brilliant. Can't find anyone to do the worktops in our kitchen and this has given me the confidence to give it a go. Will probably do a few dozens mitres on the old ones first!
Great video!...clear guidance....I was cringing when the hammer was being used directly on worktop ( always use a block )....to flush the joint....video shows how long and tedious it is to fit worktops....don't just happen....nice one....
Absolutely brilliant - very clear with explanation. This really helped me a lot. I have done one worktop before and watched this again as a reminder for another one I have to do.Thank you very much.
Beautiful video! Detailed, honest, very precious detailes and little craft secrets. And nicely recorded!
Thank you!
I watched this despite not needing to do the job being covered here, basically because it is such a great lesson, thanks for these :) Subscribed
Best video I've seen on how to install a worktop, and I've installed a good few, very informative well done!
Thanks for the video, I've just bought a kitchen and this has given me the confidence to buy a router and template and have a go doing it myself..
nice little pull focus at the end, never used a mitre, but watching this gives me a bit of confidence to try
Excuse my language but Fucking brilliant video. I've been in the kitchen trade as a designer for over twenty years and I've been told how its done but never really understood. Just watched this and it makes perfect sense now. Genius, thanks. Right, what were gonna do now (ha ha ha) is watch a few more.
+Simon Hopkins Cheers Simon hope you find our other videos interesting :)
Simon Hopkins
Keith Barraclough
Simon Hopkins
olly 1
Great explanation and demonstration, extremely clear video, first thing I was thinking watching that spanner work was that, like Max said, I'd use a ratchet ring spanner to run those nuts down, it would be a lot quicker and easier than an open end spanner, especially
if you're doing joints often.
You can score the worktop with the router, then jigsaw the rest out leaving the jig in place. Leave a couple of mm with the jigsaw. Then just clean it up, with one full depth pass of the router. It saves your router bits and router from an early grave.
Mark R - excellent tip. It also saves time and reduces mess to clean up.
I thought I was the only one that did that!
Love the name!
I meant..love the nae Alvin Sawdust.
A couple of notes - A small gap between wall and boards gives you some breathing room if there is movement in house and or require a very slight adjust from error. Probably try and use a 0.7 - 0.9 mechanical pencil to keep lines sharp .. the fat lines from blunt pencils make for bad errors. Great video ..
Tommy thankyou very much for posting. Much appreciated to folks whom take the time to educate the rest of us. As a Yorkshireman saving money always appeals. Many thanks. Lewis
Lewis McGregor time you hire the tools and the time it takes you plus the job won't be as good its wise to get a kitchen fitter
Two tips for first timers. When cutting the joint with the template, always release the router cutter upwards before lifting the machine out of the slot otherwise you will invariably nick the template with the cutter destroying the machined edge.
To tighten up the bolts, get a 10mm ratchet spanner, one from the Halfords professional
range is best as it has a very fine ratchet. Makes doing up the bolts much quicker.
Also. Bushboard do a joint compound especially for this job in matching colours.
Best instructions I've seen on yoube. Simply perfect and extremely clear.
Have to say thanks to you for the video as It helped me fit my first kitchen worktop successfully and I'm well happy, thank you buddy...
Thanks so much for this excellent and professional video.
Well planned and good photography.
I have to buy a router yeah?
I will now watch you cutting the sink hole. The last time I cut one upside down and lifted it up on my back to install, it broke. That's the last time I remember crying.
So hopefully this time I can put it in position, and then cut the hole from the top.
My biggest problem seems to be fitting the sink and drainer in between the support bars of the base units.
Thankz smuchly and God Bless.
I'm Dave not Iestyn, he's my son lol thank you Tommy for taking the time to put this video together. I'm a time served Carpenter, but I never do many Kitchen butt and scribe work?? this has given me ease of mind as I lost the instructions for my Trend jig. Can't fault you mate!!
This is so well done.
Logically explained with little tips.
I would love to work with this guy for 12 months. I could learn so much.
Would a ratchet 10mmm spanner make life easier ?
Also, is it practical to glue softwood jaws onto the C clamps to save fiddling with cardboard ?
There's some other helpful videos out there but this is probably the best of the lot. Thanks very much.
excellent video, now have the confidence to hire a jig and tackle our new worktops by ourselves
Well put together, no messing video with some good camera work. Excelent.
Went throught all videos on youtube. This is the best video. Topman
Hi, thanks for the informative video. Two questions: Why not use the jig's sliding gauge to determine the width of cut in the female?? Also, when marking the male joint, why not put the male end on top of the female cut top, supported at one end, then just scribe from beneath the worktop? Cheers Dave, Tony
Nice to see you back Dave and, a great lesson on how to as always,thanks
That was excellent, very informative, well spoken, very very helpful thank you so much.
Thanks for the video. I only had one worktop to join but it is perfect on my first attempt ever
Many thanks for this video. Watched it 3 times then hired a router and template (HSS hire bundle), had a practice on an old piece of worktop and then went for it. Really pleased with the results.
One question. Why no biscuits in the joint?
Excellent video....The guy is very good at his trade and at making videos Perfect! Help get rid of the Cowboys do you're research and use one of the good guys like this one...
"Basically," very informative.
Great video mate - thanks for posting and sharing your knowledge
This video helped me install my first kitchen really informative helped me make a great job of our worktops. Nice one
Brilliantly informative...thanks for sharing your expertise Tommy!
Love watching dave work. Great practical tips.
What a great video! Really wish I'd watch this last week before my new kitchen just got put in!
great video for a new bee or someone in the trade for years
Brilliant , excellent tradesman, explanatory detail first class
I love watchIng this guy work,
Nice video. Is 9mm specific to your router bit or is it always 9mm?
A real pro. Thanks Dave - and more please!!!
Excellent tutorial. Originally searching for a how to on cutting MFC chipboard, was thinking of router to finish off edge.
Tommy, blinding explanation! Love the banter - you can say 'basically' as much as you like as far as I am concerned! My kitchen worktops are solid wood which were in the house when we bought it. A 3m length is over £400! I have enough remaining from downsizing the tops to make up what I need by joining with straight joints. A good router will cost approx £300 (for me as a competent DIYer for 40yrs) so a router and jig it is. Please could you tell me what the make and part number is of the router you are using in the video please. I like the ease of locking and adjusting the depth. Judging as an engineer, it looks to be well engineered. Cheers, Jon
Just a thought. Once ur setup ... why not go into the jig slot and remove most of that material with a jig saw. Would save a lot of time and wear and tare on the cutter bit.
Thank you for the master class.
Great workmanship.
Brilliant informative video, a precise procedure for completing a worktop mitre joint!..😀
Great video! And you like you actually enjoy it too mate!
Quality guy every day a school day
Wouldn't make sense to cut the bulk of the material out with a jigsaw after you have your jig mounted to prevent any laminate chip out. Nice job ... I'm just thinking of cutter pull with the heavy cut. Nice video. Thanks.
Thanks for a great video - I think this is the best and clearest I have seen - subscribed :)
Excellent video, thanks!
However I can't help but notice how the sink bowl looks to be in a terrible position to use every day!! (half way in the corner of the work top)
Home owners decision I'm sure, but it just looks very awkward to me.
My only criticism with the video is the lack of hearing protection. I've spent years attached to routers and they're bloody loud. Other than that, I can't fault it, cracking vid
Paul moss pardon
perfectionist tidy work
Working for a university degree couldn't be any more difficult than the work involved in mitreing a countertop.
Would you cut the hole for the kitchen sink first or Mitre the worktop first ?
Don't want the laminate breaking.
Good vidéo ! Thanks from France.
very well explained brilliant video quality
Ratchet spanner on your Christmas list?
Second time coming back to this video as i forgot the procedure :) one question though did you use router or circular saw for straight cuts?
Brilliant video tutorial, thank you.
Awesome work, thanks for the video!
Thank you, I found this a very helpful guide to cutting in a worktop. I was able to follow the basic principles and successfully mitre together two worktops, twice for different rooms. I did have some issue with the visible edges on the surfaces chipping slightly where the cutter went along, on both the top surface and (more seriously) on the front profile edge, despite all my efforts to prevent this. The only other thing I would suggest is to not drop the router down too much on each cutting pass because this increases the chance of the router going off track as it struggles to cut too much material.
Top helpful video though
i want this guy to come fit my kitchen!
Really beautiful, shame the position of the sink in that corner probably spoil the joint with all that water splashing around it after few years.
Very interesting to watch it really shows you've done that before :) thanks for sharing your knowledge Tommy
Well done, love this video, wont prob do myself anytime soon but loved the skill, thanks :)
Good clear instruction, thank you.
that's cool! i learned something.... seriously, i learned! thank you!
Always wondered how it was done thanks ;)
You did an excellent job!!!
EXCELLENT tutorial a joy to watch, well done m8 ,:0 )
dave your the main man top class every video,
I enjoyed watching this.........for obvious reasons:)
Top video very informative, and not to flash keeping it real!
Should have mentioned about cleaning the pencil marks off also.
Good video.
Very nice mate :) well done good to see you enjoy it also. Regards Bart
Thanks for the very interesting insights! What type of router bit do you use to cut the counters?
Great video mate. Well done !
great video I would love to see a 22.5 degree cut with the jig is this possible ?
Nearly 1.5 million views, as I type. Just hope this guy is getting some £$love£$. Artisan. My DW625EK only gets the dust blown off the box 3 or 4 times a year.
Awesome instructional video, clear, concise info. 5*****. Thanks.
Really useful to watch if you are having new worktops fitted, even if your not going to attempt it yourself, you can see how its done and check the workman are doing it correct. ta
Nice one Dave. Cracking video
Very useful techniques!
Thanks for the video :)
Gorgeous Man....brilliant !!!