Rear Bumper Cover Removal and Replacement Hyundai SANTA FE 2006 2007 2008 2009 2010 2011 2012
Vložit
- čas přidán 20. 01. 2016
- Rear Bumper Cover Removal and Replacement Hyundai SANTA FE 2006 2007 2008 2009 2010 2011 2012
► Our Website for Tools, Parts and more Videos: mechaniclifestyle.com
In this video we are showing you how to remove and replace the Rear Bumper Cover on a Hyundai Santa Fe Second Generation.
It is not very complicated procedure and it should not take you more than 10-20 minutes to do it after you see the video and you know what to expect.
You will need a phillips screwdriver ( if you have one with short handle you will not even need to remove the tire), also, you will need pliers and flat head screwdriver for the clips, 10 mm wrench or socket with ratchet.
If the bumper cover is damaged we have a video on our channel that will show you how to fix it. You can check it out by clicking on this link: • How to fix CRACKED Bum...
This video should cover the following Hyundai Santa Fe Second Generation:
2006 Hyundai Santa Fe Rear Bumper Cover removal and replacement
2007 Hyundai Santa Fe Rear Bumper Cover removal and replacement
2008 Hyundai Santa Fe Rear Bumper Cover removal and replacement
2009 Hyundai Santa Fe Rear Bumper Cover removal and replacement
2010 Hyundai Santa Fe Rear Bumper Cover removal and replacement
2011 Hyundai Santa Fe Rear Bumper Cover removal and replacement
2012 Hyundai Santa Fe Rear Bumper Cover removal and replacement
► 2ND Channel Subscribe: bit.ly/2a86p9Z
► BMW E46 ZHP PROJECT bit.ly/2g8tOa9
► Ford Fiesta ST BUILD bit.ly/2a59UKp
► 2013 GT86 Project Playlist: bit.ly/2dz4xY1
Let Us Know if the Video was Helpful!
Like Us on FACEBOOK: / worldmechanicsofficial...
LIKE & SUBSCRIBE for MORE DIY VIDEOS that could SAVE YOU BIG $$$$$$$ !!!
We upload a NEW VIDEO EVERY DAY!
The title translated in different languages so we can help more people around the world through visual presentation:
Cómo quitar y reemplazar la cubierta del parachoques trasero en un Hyundai Santa Fe.
Como remover e recolocar a tampa pára-choque traseiro em um Hyundai Santa Fe.
Entfernen und ersetzen Sie den hinteren Stoßfängerabdeckung auf einem Hyundai Santa Fe.
Comment retirer et remplacer le couvercle du pare-chocs arrière sur une Hyundai Santa Fe.
Come rimuovere e sostituire il rivestimento del paraurti posteriore su una Hyundai Santa Fe.
कैसे हटाने और एक हुंडई सांता फ़े पर रियर बम्पर कवर को बदलने के लिए।
Jak usunąć i wymienić tylną osłonę zderzaka na Hyundai Santa Fe.
Cum să scoateți și puneți la loc capacul din spate pe o bara de protecție Hyundai Santa Fe.
Miten poistaa ja korvata takapuskuri kansi Hyundai Santa Fe.
Hvordan fjerne og erstatte bakre støtfanger dekselet på en Hyundai Santa Fe.
Hur tar man bort och ersätta den bakre stötfångarhöljet på en Hyundai Santa Fe.
*Disclaimer
We, World Mechanics, are not responsible for property damage or injury incurred as a result of any of the information contained in this video. Information given in this video does not guarantee the desired outcome. Any injury, damage or loss that may result from improper use of the tools, equipment, or the information contained in this video is the sole responsibility of the user and not World Mechanics. - Auta a dopravní prostředky
⛐ Check out our Garage to see what tools we use and recommend:
www.amazon.com/shop/worldmechanics
⛐ Subscribe and hit the notification bell by the subscribe button for new videos: czcams.com/channels/J9xpq0qUZevSEdBSFqO2ow.html
⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys
Cant thank you enough. I had my bumper pop out from a low impact collision and the shops here in Los Angeles that I checked (3 of them) all wanted 900-1100 to fix. I watched you video and started at 12 and finished by 1:45 having had no previous experience ever working on a car body. I am going to take the money and spend it on a weekend in Lake Arrowhead with the wife instead! Thank you once again. Your video was amazingly good!
This was great. That little trick at the beginning with the ratchet works great - the space in between the fender and the tire really is too small even for a "shorty" screwdriver.
For my 2012 Santa Fe, it was slightly different:
Instead of the four bolts on the bottom, there were three plastic brackets attached with a Philips head screw. These were hard to access so I lowered the spare to the ground first. That gave me plenty of room to get a screwdriver in there and I was able to loosen the brackets.
Peeling the panel off was a bit more difficult than shown here. I had to lift up here and there and jiggle it quite hard before the panel came loose. You do want to be firm but careful while doing this - I think I broke one of the 'clips' in the process. It might be safer if you have a friend to help push up on the panel while you jiggle and pull it.
For me I only needed to replace the rear driver side reflector (which had broken in a fender-bender). I was able to peel the bumper panel back enough to reach inside without having to remove the entire thing.
Putting the panel back on was easier than taking it off. Just firmly press in place & a couple of whacks with your fist while pushing up on the panel should get it to pop back into place. Then just put the screws back in the order you took them out.
I'm sorry, but what I really wanted to see was what the bumper looked like as it was coming off and if anything more needed to be removed for me to install a reverse sensor set I purchased. Unfortunately the 4 ads that your website popped up at that precise moment pretty well covered most of the screen and ruined any chance of that. And, as the other user pointed out, you did not mention disconnecting the wiring to the fog lights.You could have added those 4 viedo promos after the bumper was off and almost on the floor. Thank-you for the very good underside shots of screws and fasteners though.
I have a Kia Sportage UK model but great video and basic principles to removing the bumper 👍
Thanks for the help. And i need to remoce the spoiler. I already remove two scrubs, but it still stock. Thais
Thanks for video was a big help
Great video. You just forgot that after losing all screws and before taking off the bumper you need to disconnect wiring from fog lights.
Dope video
Hola, disculpa el proceso de desarme es igual para la santa fe del 2014?
great video. thanks
It would be great for you to show us how to replace a damaged bumper reflector too!
Would it be the same procedure for an 04 Santa Fe?
bonus points for your sweet watch
I have 2017 Hyundai Tuscon, can this same process be used?
can i do this with my carens 2015?
can upload a video to remove 2014 hyundai sonata please
Hello, I have a problem with my back door 09 Santa Fe does not open but days ago I worked, could you please help me
You know what that pinky nail is for 😵 lol @ 1:22
Там ещё 2 клипсы есть с самого верха изнутри платиковые видать у вас не было их у меня были долго искал что держит.
Someone must have removed that bumper previously... because there are two additional bolts (in addition to the ones they remove) that hold the bumper on... they are located on the left and right "ears" just below the corner of the tailgate. You can see them in the video...
Do you know, how you get to them? I had to remove mine, but could not figure out how... THX
@@danielcancar1423 i think you can get to them from underneath. However, i did not know about them since i went by this video and they neglected to mention them... and by pulling the bumper with some force they broke off. These screws mount into a push type bushing that goes through the hole.
The plastic screws used on the bottom of the left and right sides strip out quite easily as well.
All in all i think i'm going to replace these factory fasteners with better ones as it seems that Hyundai cheaped out on fasteners.
@@rvborgh thank you sir! All the best for the next decade
Last 10 seconds of the video are covered by ads! Also, you mention for the four bolts underneath: they "tend to get rusty". They're attached to plastic bars. The bars bend when the bolts are rusty and I am finding the bolts impossible to remove!
do you have to take off the bumper to replace the inset rear light??
Abell Morliss I don’t know too, please if you figured out let me know