Install Toni System Red Dot Plate on Beretta 92X Performance
Vložit
- čas přidán 2. 04. 2023
- Took 7 months of wait time to get this fabulous plate. The installation took a LOT of hammering. I think Toni System could have made the dovetail insert slightly smaller so that it can go in easier. After all there are two set screws. If you have seen how easy it is to remove/install a rear sight for Walther Q4/Q5, you’ll know what I’m talking about.
@BERETTA9mmUSA @BerettaCommunity @toni.system - Sport
Very good work sir👏👏love from India😊❤
Great video just subbed 👍🏽
Will this fit a beretta 92fs? Does that plate support the holosun 507k footprint?
Yeah
Where did you get the chrome barrel from i want to change out the black one that came with mine
jarvis-custom.com/
Make sure you tell them what exact pistol you have so that they can ensure the best fit.
Hey, so how is the plate holding? I'm now deciding which Beretta to buy, a regular like yours or RDO? Did you have any issues with a plate? Thanks.
No issue at all. It’s holding extremely well. It took me a lot of effort to hammer into the dovetail so it’s not going anywhere. If you aren’t confident of doing it yourself, you should buy an RDO version.
@@9mmtactical Nah I'm ok :) I have the same "wiregear" tool. Now I just can't decide on Beretta 92x Performance or 92x Centurion RDO. Somehow I like more Centurion RDO more because of the lighter weight, but I need Beretta as an alternative to Shadow 2 (amazing pistols, but design-wise it looks like a WW1 gun :D)
LOL I know what you mean.
Hi Sir , the mounting screws for the dot on to the tony system plate are M3,5 thead? thanks
Different holes on it have different sizes. For Vortex Venom that I installed, it might be M4. Sorry I don't remember and can't find the record of where I got the screws.
@@9mmtactical yes, thanks that's why i am asking to you it is not wrote down in any site thev screws tyoe
@@chriistar nope sir.. till now i could not be able tu put my hans on one of those
What compensater did you get?
It’s Beretta’s factory compensator. You can see it on their website.
Do you think this would fit on a beretta 92fs replica Pellet gun ?
I’m not sure. But if the slide is an exact replica, it should fit.
92fs has a different dovetail - it is less wide and I don't think would accept this plate.
How can I purchase one of these if I’m in the us
www.optics-trade.eu/us/mounts/shopby/manufacturer-toni_system.html
i get the plate for rmr pattern, after instal, i couldnt zero rmr because lack of vertical adjustment, for 15m i was like 10cm up from center... 😢 anyone had same problem? or solution??? thanks!
Yes I know this issue. You probably filed too much material off of the plate? Now after you put the set screws the plate is pointing too high and you can’t lower to dot further. It will help if you have the third set screw and put it in the hole that’s in between the two set holes but behind them. That will tilt the plate a bit and force it to point lower.
Also, to confirm, did you mean that your dot was too high from the center and you can't lower it further or your bullet hole (impact point) being too high?
@@9mmtactical thanks for answer, plate is tilt down, in front like 1 mm from frame of the gun, so i cant tilt plate any further... btw we didnt get any material of the plate, it sits right out of box....what i mean, my point of impact is too high
@dalibormotycka3037 oh I see. Then you can do the other way around. You can file off a little bit material from the front edge of the plate that touches the dovetail. That way after inserting into the dovetail the plate can point upward a little.
Kako ta mož strelja, ko mu ne gre delo in razstavljanje pitole od rok 🤔
I'm scared viewing this!
beretta mounting system no good