Tiny SMPS 12,6V 10A Without IC | Simple Circuit | Full Detail With PCB Share
Vložit
- čas přidán 22. 08. 2024
- $2 for 1-4 Layer PCBs, Get SMT Coupons: jlcpcb.com/DYE
►Tiny SMPS 12,6V 10A Without IC | Simple Circuit | Full Detail With PCB Share.
►All-electric component you can buy from utsource.net?source=CZcams
►Hi Friends. Today I share with you Tiny SMPS 12,6V 10A Without IC | Simple Circuit | Full Detail With PCB Share. You can download all files below.
***************************************************************
I hope you like my project, you can donate me some money for I can buy electronics component to make a new video with high quality.
***************************************************************
Donate me click here: paypal.me/Long...
Contact me on Gmail: Youkito1991@gmail.com
Have a nice day my friends
***************************************************************
Download all file here: drive.google.c...
AC TO DC 20A : drive.google.c...
***************************************************************
List of electronics component:
MJE13007: www.utsource.n...
Triac DB3 : www.utsource.n...
Resistor 680K : www.utsource.n...
Resistor 2.2R : www.utsource.n...
Capacitor 1uF/250V : www.utsource.n...
Capacitor 1nF/2KV : www.utsource.n...
Bridge Diode 5A : www.utsource.n...
***************************************************************
Another video:
• Simple 220V to 5V 2A 2...
Simple 220V to 5V 2A 24V 0 3A Without Re Winding JLCPCB E exhibition
1200VA Pure Sine Wave Inverter 12V to 220V Using Ferrite E42 Core + Egs002
• 1200VA Pure Sine Wave ...
300W PFC, Controller, Continuous Conduction Mode, Fixed Frequency, Compact | PCB and Schematic
• 300W PFC, Controller, ...
How To Make 24V 20A Switched Mode Power Supply With Short Circuit Protect | Feedback Circuit
• How To Make 24V 20A Sw...
2000W Switched Mode Power Supply With PFC Power Factor Correction | Final Version 100V 20A
• 2000W Switched Mode Po...
1000W Inverter 2 Transformer with ShortCircuit, Low Voltage Cut OFF ,Reverse Battery Protection
• 1000W Inverter 2 Trans...
Powerful 200W inverter 12V to 220V Simple inverter using SG3525
• Powerful 200W inverter...
How To Make 50V Switched Mode Power Supply With Short Circuit Protect | Feedback Circuit
• How To Make 50V Switch...
DC Current Protection Project | OverLoad and Over Current | Short Circuit Protect
• DC Current Protection ...
An Exhaust Fan Control Circuit | Adjusting The Turn off and Turn on Time Easily
• An Exhaust Fan Control...
SG3525 24V 20A DC Motor Speed Control PWM Frequency Adjust by Potentiometer
• SG3525 24V 20A DC Moto...
Flyback Transformer Design Software | 12V 5A Switch Mode Power Supply | Short Circuit Protection
• Flyback Transformer De...
Ferrite Transformer Turns Calculation and Rewind Transformer | 500W SMPS Short Circuit Protect
• Ferrite Transformer Tu...
LM393 + Mosfet IRF540 IRF9540 Small Amplifier but Powerful with Good Sound and Clarity | Milling PCB
Show me which core do you have, size ? material ? ouput voltage ? wat? i will help you calculate winding detail ?
Kindly tell us about yellow white ferrite ring from atx
It's not for SMPS change another core with material PC40
Ok kindly you mention some which can be easily available to everyone
EE33 EE35 core from ATX. Next video i will make simple smps with that. Just a few component but can reach to 300W
Sir you kindly tell us the detail of your core and winding
Hi. I built your circuit but it did not work at all. There was no output. The voltage across the Diac is 24 volts.
please guide me.
Wow... You are amazing... You are not stopping to amaze us ❤️
I always found awesome inventions from you which even don't exist on the internet... Love you
Thank bro
Once again you have given an amazing project...🔥
Thank vro
Brother, you have made a lot of detail video.
Hi. It is excellent. If possible, do a project for a variable power supply with a voltage of 0-40 volts and 0_40 amps. 220V input and half bridge. It is very useful for testing the inverter instead of using the battery. Thankful
Maybe next time bro. I so busy now
Yes with thanks
Excellent
Thank bro
Good work thank you ...
BUT ...
Please upload circuit diagram
Brother you are genius.
Are these safe? what is the ripple like?
can it be used for mini amplifier?
CAN YOU PLEASE ADD THE SCHMATICS TO YOUR PROJECTS?
Its an request please make one special video on how to increase the current of any smps supply. Beacuse voltage can be adjusted from winding but increasing current is what we don't know
Increase current by increase diameter of wire
Thanks for sharing
Thank bro
muito simples , vou montar uma pra mim fazer uns teste , like
hi friend it works great put i am facing 2 issues first one i need to reconnect it to the ac many times to start working
i add a bridge and capacitor it works
2nd issue the furrit ring become too hot after like 1 minute even if no load connected .
Check small driver transformer. Maybe the material is not good.
@@LongTechnical thank you my friend I think u r right
good job broo
Thank bro
I love it!...please tell me you are up for the 24v version of it....coz i can't wait to see it!
Change number of turn to 18 Turn you will get 24V at output
@@LongTechnical thank you mister...
Circuit diagram??
bro can i use the inductor from old induction heater? the diameter is 1.5cm
Of course bro
sir can i use ee35 from old atx with no air gap.please tell meprimary turns??.secondary turns for 32v 5amp??🙂.you have uploaded a smps circuit with atx transformer but that has double sided pcb😔🤒
Can it be used with EE-35 ferrite ? and what would be the primary winding
Thanks for the time, work and sharing what you do good project ... and in turn asking the ferrite donita of which measure more or less serious and the cable for the secondary is enameled or not, please Thank you.
Greetings!!!
Of course. the wire of secondary is enameled
@@LongTechnical The ferrite donut, I can put a sercana measure or it has to take the measure that it is and what would be the measure thanks:
what do you mean bro ?
@@LongTechnical of what measure would the small toroidal be
Full kit available ?
Kaynak makinesi yaparmisin ustam kolay gelsin
have you done projects with cc/cv?
No bro
uotput doesn't need diode and capasitors?
But your npn maxA rating is 8Amp then how we can get 10 amp?
Increase diameter of wire
How to buy this board& how much
Or a phone charger of that nature...5v 2A/3A...
Anh có mạch 220v to 12v Dc công suất lớn không ạ
Can we touch the output points? Will it give shock?
Yes. We can touch. They are isolated
مدارشو بزارید
Cost ?
Where from i will get the PCB
Use gerber file and upload to jlcpcb
Need circuit diagram
Its just electronic transformer for halogen lamp without capacitors.
Looks like it
Cho em xin sơ đồ với anh Long ơi
buenas tardes por favor no me funciona nada hecho como esta tal cual y no me funciona
is. AC o DC
Dùng lõi ferit khác đc ko a ferit xuyến có đc ko a
Được em ee35 42...ok
@@LongTechnical sao lại ee
Lõi tròn đc ko a
@@khuynguyen3626 lõi tròn hay lõi ee đều được em
@@LongTechnical cảm ơn làm nguồn 220v xuống 12v 20a đi a
Circuit diagram please 🙏❤️❤️❤️
Bro circuit diagram ka pdf open kyo nhi ho rha hai ❤️ bta do please
I made same circuit and i connect it with 100 watt series bulb and it run for about 3 to 4 second and transistor get too hot and blow up and now when i connect with out load tbe series bulb glow at full bright whats th problem???
Check your transformer and driver. Maybe the material is not for SMPS
@@LongTechnical no the material is for smps but i think the driver tramsformer was little small is that a problem??
Yes. Please check it
@@LongTechnical what is the driver transformer size??
I take out driver transformer from 24 watt cfl light and just wind it 3turn 1t 3t...
@@LongTechnical and it was ferrite core
can i us atx transformer?
i need de circuit diagram pls
excellent bro
I sent to you an email please reply to me
thank you, bro
How can I build when you didn't leave any plans?
it save to used long time? im scare to used my build smps...🤣😂🤣😂 after first time im build get blowup..make my wife 😡😤😂🤣😂
5v 10a
Nguồn vào 220v hả
Uh
@@LongTechnical thanh you
Download file cant open.
Download winrra app
This can't give upto 10A
Do it before comment
@@LongTechnical where am actually confused is that is it 220VAC to 12.6VDC 10A?
dieser kanal ist nur werbung.sorry
I hate ringcore
Why ?
مدارشو بزارید
مدارشو بزارید
مدارشو بزارید