Drill a Square Hole Hollow Chisel Mortising Bit
Vložit
- čas přidán 12. 11. 2022
- Drill a square hole. Use a properly prepared mortising chisel and auger bit to drill a square hole in pine and then later in the video in hard maple to show the effectiveness of this technique.
Hard maple is Mortised at the end of the video with a 3/4" mortising bit. - Věda a technologie
The video was very helpful to me. Thank you very much!
Thank you very much for your comment. I have another video on step-by-step, sharpening and actually another video on close-up views of how to sharpen and polish the chisels and auger for the mortising bit. Consider subscribing. Thanks, Joe.
@JosephHunstad thanks for the lesson. The mortise bits I received came with zero instructions. I tried using them once...the chisel was spinning like crazy! Clearly I did something wrong. I stopped it immediately. Those suckers are wicked sharp! I didn't know about the diamond bit for the inside...I'll have to invest in one.
Go through all the steps of sharpening these including honing the inside it will make a huge difference. If Chip ejection is not easy, then Wood will build up and heat and burn inside of there, so follow the directions and yes those diamond homes from Rockler or actually Amazonare really good and Chuck went in your drill press and then just carefully rotate that to sharpen them. Consider subscribing. Thanks. Joe.
Always wondered how this worked. Now I know!
Hello David! Thanks for your comment. Consider subscribing. Thanks Joe.
It was published December 13, 2020 take a look at my channel and then there’s another follow up that I did a few weeks later that has a real close-up video of the auger bit. I’d recommend looking at both of those. Thanks. Joe.
Is it possible to use this machine to create a vertical square hole in a piece of wood that will be installed at an angle? I've got half-inch square balusters/spindles and I don't want to use a baluster shoe, just a clean square hole to accept the balusters as they go down the the angled trim cap (not being installed on treads). Would you use an angled jig to hold the cap at the correct angle before drilling? Thanks in advance!
OK you ask a great question. There are some machines that the head actually will tilt but mine does not do that. If you have a tilting machine, that’s great. You can set it at the angle desired entry your hole. For those like mine, that the head does not pivot, an angled block beneath the workpiece will give you the proper angle and then you can enjoy your hole. That would be my recommendation. Consider a subscribing. Thanks. Joe.
@@JosephHunstad Thanks! Done!
now that's a drill press.
Yes, well it’s actually a dedicated mortising machine whose sole purpose is to drill square holes. I made a dining room table for my daughter that had 150 mortise tenon joints. This machine made it happen consider subscribing. Thanks, Joe.
Do you need a special drill press to do this ? Mine doesn't have a collet. It's just a regular one from Harbor Freight. Can I adapt it for this use ?
There is a specific mortising attachment for the drill press that you can purchase. It works OK and that’s what I would look into getting. That will work with a standard drill. Press. Consider subscribing. Thanks, Joe.
@@JosephHunstad Ahh, I see it now. I was missing that part of the puzzle. Ok, I'm gonna get it. Thanks for your reply. I subscribed. Cheers.
What brand of machine is it?
Hello there thank you for your question. The brand of mortising machine that I’m using is a jet. There are many different manufacturers that make good products. The mortising chisel‘s are also made by jet made in Taiwan. There are certainly much more expensive sets on the market that are probably better out of the box but these have worked beautifully for me once I’ve sharpened and honed them. Take a look at my other videos on mortising bits sharpening to get them truly user-friendly. Consider subscribing. Thanks, Joe.
Wow that's super helpful man, thank you! (FYI, this is very pedantic, but you could do with investing in a better microphone. Your content is so good it's a shame there's so much hissing.)
Yes, you’re absolutely correct. I have just recently purchased a new wireless RODE microphone, and it has helped a lot. Consider subscribing. Thanks. Joe.
Quick question, do you think it needs to be re-recorded and the original deleted?
@JosephHunstad No, it's not that bad! I just thought it would help you in the long term, as it could lead some viewers to reach an unfair conclusion and look elsewhere. The main thing is the content is great! Hope that helps.
Whilst I am writing this, I may as well ask the question: I tried using my mortiser yesterday after watching your video. The bit wouldn't cut into the wood, even when I applied extra force. Do you think the bit isn't sharp enough? Or could it be that the rotating inner part is positioned too far into the square outer part? Also it was very noisy. Is there a particular lubricant I should be using? Thanks :)
@@charlespell7762 OK great question no your mortising bits are not sharp. I have another video on my channel on the step-by-step method to sharpen these perfectly. I’ve reviewed all the other videos online and honestly the one I’ve created is the most complete. If you follow those directions you will create Morris bits that make the whole process super easy, clean no burning, the noise rattling, etc. will stop and it will be a joy to use.
@@charlespell7762 it was published. I think December 20 in 2020.
Hi like this bits is I required
I perchez this bits send me
Hey there. I don’t fully understand your question but yes to drill a square hole you need mortising bit. You can get an adapter to fit on your drill press or buy a mortising machine. There are many available with quite a variety of prices. Consider subscribing. Thanks, Joe.