Video není dostupné.
Omlouváme se.

MR JE C Servo with FX5U Part 1 (CC link IE Field Basic)

Sdílet
Vložit
  • čas přidán 22. 03. 2020
  • CC Link IE Field Network Basic is compatible Servo Amplifier MR-JE-C.
    GX-Works 3 Parameter Setting
    • Device Numbers Used For Read/Write Function
    • Communication Start Setting
    • Program Operation Modes - Velocity Mode
    Device Numbers used to Write from Master station to servo Amplifier and to
    Read from Servo Amplifiers to Master station
    ------------------------------------------------------------------------------------------------------------------------------------------
    Program Sample At:
    automationsolu...
    automationsolu...
    Download Sample Section
    ------------------------------------------------------------------------------------------------------------------------------------------
    To operate the amplifier in velocity mode switch amplifier to “Profile
    Velocity Mode (pv)”.
    • To Switch the amplifier to “Profile Velocity mode (pv)” write value ‘3’
    (i.e. K3) to Control word (i.e. RWw00).
    • After switching to “Profile Velocity Mode (pv)” write “Target Velocity”
    to Speed Command (pv) (i.e. RWw00 + 07).
    • While operating the amplifier in “Profile Velocity Mode (pv)”, the “Bit
    No. 15” should be on with the start command.
    • To start velocity movement write value ‘32895’ (i.e.K32895) in control
    command. (i.e. RWw00 + 01).
    • Depending on the sign of “Target Velocity” direction of movement will
    be decide.
    (i.e. Positive velocity Forward-Rotation,
    Negative velocity Reverse-Rotation.)

Komentáře • 31

  • @davidekadukowski4656
    @davidekadukowski4656 Před 2 měsíci

    What are the first 2 lines for?

  • @erickreyes397
    @erickreyes397 Před 2 lety

    Hello, could you provide me with the manuals that appear in this video?

  • @ghalib4610
    @ghalib4610 Před 3 lety

    Dear sir thanks for always your support
    What will be the controlword(6040) value for servo stop & speed change during servo running in pp mode

    • @Technocrats91
      @Technocrats91  Před 3 lety

      check 605Dh for stop during PP Mode

    • @ghalib4610
      @ghalib4610 Před 3 lety

      @@Technocrats91 The shaft also unlocks when I stop servo

  • @balajidevaraj2740
    @balajidevaraj2740 Před 4 lety

    I did not see MR-JE-C series in my Gx works3, I am usingV1.063R, please advise how to get required servo amplifier in network group

    • @Technocrats91
      @Technocrats91  Před 4 lety

      First update your gx works 3, after update if it doesn't show mr-je-c then you need to add profile manually in thst case download profile for mr-je-c from Mitsubishi site and add it to gx works 3

    • @nekilood422
      @nekilood422 Před 4 lety

      @@Technocrats91 Sorry for my stupid question but how can I update GX works or how can i add and where to download profile for the amplifier. I recently started working with Mitshubishi PLC so I'm pretty new to it so again, sorry for stupid questions. :)

    • @Technocrats91
      @Technocrats91  Před 4 lety

      @@nekilood422 follow the steps to download updates
      czcams.com/video/nKKgchmmEVE/video.html

    • @ghalib4610
      @ghalib4610 Před 3 lety

      @@Technocrats91 how to add profile manually

  • @andrewnauth4899
    @andrewnauth4899 Před 3 lety

    Can you use Mr-J4-GF with FX5U the same way?

  • @hapham-qd4jl
    @hapham-qd4jl Před rokem

    how to turn SON ON.( Servo ON). Don't use CN3

  • @sheikameer8235
    @sheikameer8235 Před 2 lety

    How Y177 and x177 is selected?

  • @sompongsuttiprapa1191
    @sompongsuttiprapa1191 Před 2 lety

    GX-Works3 Ver. ??

  • @ashitoshdhamankar2001
    @ashitoshdhamankar2001 Před 4 lety

    in case of brake motor, how to make servo brake ON?

    • @Technocrats91
      @Technocrats91  Před 4 lety

      In case of Mitsubishi Servo Drive and Motor with brake, we have a dedicated output for brake known as "MBR" , you need to wire the brake through that output, drive itself will take care of brake.

    • @ashitoshdhamankar2001
      @ashitoshdhamankar2001 Před 4 lety

      please send manual which is shown in video (for RWw & RWr mapping)

    • @Technocrats91
      @Technocrats91  Před 4 lety

      @@ashitoshdhamankar2001 type MR-JE-_C
      SERVO AMPLIFIER
      INSTRUCTION MANUAL
      (Network) on google

    • @ashitoshdhamankar2001
      @ashitoshdhamankar2001 Před 4 lety

      For Fx5U, in which word we get servo running pulses (Y0, Y1), Like D8340 in Fx 3U.

  • @albershaikh2032
    @albershaikh2032 Před 3 lety

    Sound???

  • @tayyenfood1010
    @tayyenfood1010 Před 4 lety

    Does jack cn3 use

    • @Technocrats91
      @Technocrats91  Před 4 lety

      Can be used if required, like LSP, LSN, EMG Etc

  • @omprakashbudhwant5794
    @omprakashbudhwant5794 Před 4 lety

    This is part 1 only , part2 ?

  • @muhammadfassil4726
    @muhammadfassil4726 Před 4 lety +1

    Part 2 ??

    • @Technocrats91
      @Technocrats91  Před 4 lety +2

      Due to unavailability of MR-JE-C servo physically at present i am unable to make part 2, i will upload it soon.

    • @Technocrats91
      @Technocrats91  Před 4 lety

      czcams.com/video/JmJsNKxD2Ro/video.html

    • @muhammadfassil4726
      @muhammadfassil4726 Před 3 lety

      Under Settings Statement label...you have dmov k1000 to target velocity then how could other speed setting value move to target velocity

  • @patelromilnareshbhai
    @patelromilnareshbhai Před 4 lety

    Can i have a mail id for communicat with you regarding mr-je-c ?