Make sure to give the video a thumbs up and subscribe! Don't forget to leave a comment and follow my instagram @kyle.corbett FOLLOW ME! Instagram: kyle.corbett Tik Tok @kylecorbett.official
@@kylecorbettI'd like to see you rebuild it...probably only needs a top end kit...check your crankshaft seals...if they leak it will never run correctly...take it and ride it as hard as you can no mercy to see how much it will take riding ...
@@bentboybbzneeds more then just a top end guaranteed that crank over heated aswell I bet the big end bearing siezed plus piston siezed to cylinder wall
Would love to see a wide open highway ride until it blows. I remember when I had a big bore tuned 50cc, I ran almost always at top speed to keep up with traffic. It would drive at top speed for 2 hours with almost no breaks, and cylinder and piston was still decent. had a little worn line between the exhaust ports.
When you run whit the bike on the street it use lower rpm, when it is in neutrale it goes at higher rpm becouse doesnt have to push the weight of the bike
@@dinglesdingler1211Fyi: A carbureted 2-stroke like this one has no rev limiter. Therefore it would rev higher without load than it would with. The reason it stops revving is not a limiter, but simply it using up all the air and fuel it can get
Good job Boss Man. The bike would never be ran like that. It should have a load. What is the point? Yes they rev so high and last a very long time. I drive a 380 KTM wide open all the time for short periods. It is on its std. bore. I am sure it might last less than a minute full throttle without a load. How about getting 4 sticks of dynamite and blowing it up in 1.5 million pieces. Then rebuild it for us. Or how about draining the engine oil from your car run it wide open so we can see it seize and lock up. Done so many times before. Sort of predictable I call all what you do a waste. And as I reported before...I peed in the Bultaco 250 and it would not start. That was a scientific experiment ..eh? What did I learn? Urine is not a hydro carbon
Looks like the engine only seized so shouldnt be too big of an issue right there. Did seem to leak water from the pump casing probably due to so much sudden pressure so that might need some attention aswell. Otherwise that engine did surprisingly well considering what its gone thru lol!
If he can rebuild it it's not expensive at all. Lol labor is the most expensive thing. He basically is trading his time for content. Seems cool where are u located kyle
@@hyjnx oh man I love pit bikes and smaller cc big frames, I love my 450 and being able to wheelie over little holes even in fifth gear but riding the klx110 is fun no amount of hp can replace
@@Mikehoncho191 My 1991 DT125R took 5minutes like a champ and I rode 5000km with the piston afterwards. I was angry at it for the spark jumping over the sparkplug boot when it got wet so I figured I'll dry it up with force 😂 That means 5 minutes full throttle 10 000-11 000rpm sitting still.
i like a yt video like 1 time every 2 years or something and i left u a like and subscribed i’ve recently decided i wanted to get into dirt bikes trying to learn as much as i can i just turned 18 i’m gonna save for 1, your gonna grow on youtube fast i can tell u that and in the future when u have a bigger fan base you should do a meet up go on a ride or something but keep up the good work man🤝
Awesome man thank you. Save up and get yourself a bike. I promise it’s worth it. I plan on doing bike meet ups once I get a little bigger. I plan on doing both dirt and street meet ups!
Honestly suprisingly. My 125 Chinese 4 stroke would last 10+min rev limiter and still started 1st kick everytime. Ended up selling it snd i belive still runs
I had a Kawasaki kh100 when I was a kid. once i was riding it it did the same thing and i just put it in 1st gear and pushed it backwards. it got unstuck and got me back home. I think there was a problem with its crankshaft.
How many of y’all are sitting here knowing what’s going on and what’s gonna happen and still shaking your head as you watch it🤦🏼♂️😂cause that’s me shaking mine…poor bike
I'd like to see if u put some powerful fans on the radiators etc if it would have been able to cool itself an stay pinned alot long. Seems like it basically just overheated an siezed up..
that is some pure dedication sacrificing his bike just for his fans!
Ya with only 7k subs probably won’t make any money 2:55
😊oh I watched more and you are rebuilding it so then it kinda makes sense anyway great video so far
@@pambarkman9950 this video has the potential to blow up & help his channel big time . Risky but I see it paying off here soon!!
it's for science
@@theoldhusky5089 😂😂😂
Bro said he’s gonna send it in a pond for 24 hours 😂 is this the new whistling diesel?😂
Screeming gasoline is hes name
I love whistlindiesel
Oh fuck ya
Hahaa, riding my crf110 full throttle till i crash
Fr lol 😂
Would be nice if you could also show us the damages when you're finished , was hoping u do one for when u killed it with the diesel
Don’t worry I filmed an engine tear down after the diesel just haven’t posted it yet.
@@kylecorbett can you post it its been 3 weeks
@@kylecorbettI'd like to see you rebuild it...probably only needs a top end kit...check your crankshaft seals...if they leak it will never run correctly...take it and ride it as hard as you can no mercy to see how much it will take riding ...
@@bentboybbzneeds more then just a top end guaranteed that crank over heated aswell I bet the big end bearing siezed plus piston siezed to cylinder wall
Jesus. That’s was hard to watch. I always hate to see a bike die like that. Breaks my heart
Would love to see a wide open highway ride until it blows. I remember when I had a big bore tuned 50cc, I ran almost always at top speed to keep up with traffic. It would drive at top speed for 2 hours with almost no breaks, and cylinder and piston was still decent. had a little worn line between the exhaust ports.
I would love to do that just to see how long it would take. Only problem is it’s not street legal. Maybe if I find a runway long enough I can try!
When you run whit the bike on the street it use lower rpm, when it is in neutrale it goes at higher rpm becouse doesnt have to push the weight of the bike
@@kylecorbettsend it
@@Lele-vi3ruNo. Just no. The rev limiter is where the rev limiter is. Bikes last on the street bc they have air flowing through the radiators.
@@dinglesdingler1211Fyi: A carbureted 2-stroke like this one has no rev limiter. Therefore it would rev higher without load than it would with. The reason it stops revving is not a limiter, but simply it using up all the air and fuel it can get
Today’s episode of “wtf am I gonna do with all this money” 😂😂
don’t matter man he worked for it and he’s gonna rebuild it
Good job Boss Man. The bike would never be ran like that. It should have a load. What is the point? Yes they rev so high and last a very long time. I drive a 380 KTM wide open all the time for short periods. It is on its std. bore. I am sure it might last less than a minute full throttle without a load.
How about getting 4 sticks of dynamite and blowing it up in 1.5 million pieces. Then rebuild it for us.
Or how about draining the engine oil from your car run it wide open so we can see it seize and lock up. Done so many times before. Sort of predictable
I call all what you do a waste.
And as I reported before...I peed in the Bultaco 250 and it would not start.
That was a scientific experiment ..eh?
What did I learn? Urine is not a hydro carbon
Everclear pre-mixed sounds like an amazing idea after it's got some heat cycles on it after being rebuilt
I know your going to rebuild the yz, but dude that hurts my soul watching it die,
And yes I would like to see the autopsy results and the rebuild
This video can only be described in one word: PAIN
Looks like the engine only seized so shouldnt be too big of an issue right there. Did seem to leak water from the pump casing probably due to so much sudden pressure so that might need some attention aswell. Otherwise that engine did surprisingly well considering what its gone thru lol!
If he can rebuild it it's not expensive at all. Lol labor is the most expensive thing. He basically is trading his time for content. Seems cool where are u located kyle
@@collind9753it doesent take long at all to rebuild it
@@collind9753"it not expensive at all" yeah if it just needs a piston lol let's see if he needs a new cylinder then it will get a little costly
@@bobthenob9017 I'm just saying if u go to a shop the labor is usually the most expensive part. Since he is doing it himself it saved alot
Rebuild it or not... what a waste😢
One of the best vids I’ve ever seen! Loved it
I’m glad you enjoyed it, thanks for watching!
Love these videos!
You should blow up a 4 stroke of similar CCs and see how it compares.
My cousin has a Yamaha ttr125, he rev that thing so much it’s awesome, I bet it’ll go for at least five minutes
@@Mikehoncho191 That sounds sick im riding a 2014 crf250 but smaller displacement bikes have a special place in my heart
@@hyjnx oh man I love pit bikes and smaller cc big frames, I love my 450 and being able to wheelie over little holes even in fifth gear but riding the klx110 is fun no amount of hp can replace
@@Mikehoncho191 My 1991 DT125R took 5minutes like a champ and I rode 5000km with the piston afterwards. I was angry at it for the spark jumping over the sparkplug boot when it got wet so I figured I'll dry it up with force 😂 That means 5 minutes full throttle 10 000-11 000rpm sitting still.
I have a 125 4 strokes that the whole family used crashed with, and revved to the limitor everyday, 260 hours pistons sweating for his life
This was so painful to watch and hear it blow
You should have heard it in person it was 10x worse
Id have cried for sure
Love the way you added that comment about certain beer brands 😂
thank you to sacrifice the bike to entertain us , def got a sub from me , keep going mate
Next day on face book market place “lightly used,never abused,runs perfectly fine.”
Would love to see how you rebuild the bike. That's something I've always wanted to learn how to do.
Thought you’d have millions of subs yet you have 9k… you deserve lots more!
Subbed now 😊
He earned a sub for the sacrifice of his bike
Bro this dude is so underrated he has the best vids ever
Can’t wait to watch the rebuild video
I LOVE WHAT YOU SAID ABT THE TAPS SODAS
Dude I love this so much
This hurt my soul watching my dream bike go to waste😢
Glad to hear that you swapped tape soda brands 😂
Great video btw!
This some whistling diesel shit right here 👍🏻
Great Videos! I bet you will become a big youtuber in some time... All the best! :)
i like a yt video like 1 time every 2 years or something and i left u a like and subscribed i’ve recently decided i wanted to get into dirt bikes trying to learn as much as i can i just turned 18 i’m gonna save for 1, your gonna grow on youtube fast i can tell u that and in the future when u have a bigger fan base you should do a meet up go on a ride or something but keep up the good work man🤝
Awesome man thank you. Save up and get yourself a bike. I promise it’s worth it. I plan on doing bike meet ups once I get a little bigger. I plan on doing both dirt and street meet ups!
Serious Dedication
Absolutely awesome video!
😂 great content brother subbed!
Just subbed. Love the creativity.
Of course we want to see the rebuild/damage. Looking forward to see what failed
Love the videos
My new man
u just blew up my dream bike
I watched the Honda run on diesel last night then this one popped up today. I’m subscribed now.
Love it!
this guy iz crazy i love it
To be fair in comparing brands, you would want to have the same hours on the bike and either the same oil mix ratio or factory recommend ratio
Love your videos
He's sick after he blows it up
I appericiate this because i didint know what would happen when you blow up a engine so thanks
Definitely want a teardown video
This was a intresting video ❤
I’ve just watched my dream bike blow up
Lasted less than a minute..... "Thats what she said" :D
this was so hard to watch! but it’s for science!!
Not the video my wife wanted to hear before bedtime.
😂😂
Make a full detailed rebuild video! PLEASE PLEASE PLEASE
Great vid. You deserve more views for your sacrifice for knowledge!
Thank you 🫡
@@kylecorbett yup
This man needs over 1mil subs
Great content!!
in veneto we say “bravo mona”
Every 150 rider be like
Honestly suprisingly. My 125 Chinese 4 stroke would last 10+min rev limiter and still started 1st kick everytime. Ended up selling it snd i belive still runs
Chinese bikes are ether lasting 6 months or they never stop. i have a lawn mower that is a chinese brand and its 40 years old and starts first pull
Do a 250 4 stroke but I love your vid and you earned the sub
Was it up to temp. When you did this?? If not that would happen to any engine.
I had a Kawasaki kh100 when I was a kid. once i was riding it it did the same thing and i just put it in 1st gear and pushed it backwards. it got unstuck and got me back home. I think there was a problem with its crankshaft.
What ratio of gas oil mix? How did the plug look after blown?
Sounded like it already needed a rebuild at the start
😂😂😂😂😂
Damn I wasn't really expecting this video to really come out, Ill drop a sub for the dedication. I say 6 mins
I appreciate it 💯
How many of y’all are sitting here knowing what’s going on and what’s gonna happen and still shaking your head as you watch it🤦🏼♂️😂cause that’s me shaking mine…poor bike
This is cool! New ideas are rare these days. Let's see a bunch of blow up testing! Let's see the Carnage inside!
Just curious was the engine warmed up before this test was started?
This dude is the wistlindesiel of the bike community lol i love it tho
Haha thanks just trying to make fun vids for people to watch!
POV 50 dads at the track warming up their kids bike
this guy was hammered during this and regretted it right after HAHA, there aint no way
No he wasn’t
Are you going to rebuild it
Edit i just seen the part where u said u gonna rebuild it
To be honest the voice is way better than the girls screaming on my bed
nooo such a nice bike and here i am struggling to find a bike with the money i have
Damn that would be my dream bike really could have put that bike to good use
You'll get one mate they're out there for cheap sometimes
it blows up because it gets to hot, u should put a fan in front of it to so it doesnt overheat and u can see how much it last like that
lets see that 150 rev until that blows up
Haha not sure about that one. I’m already busy rebuilding the 125 lol
Now that’s how you warm up a 2 stroke
New subscriber from Vancouver, Canada 🇨🇦 great channel 👍
Thank you 😎
@@kylecorbett no problem
Two minutes and five seconds, I think that’s when it’s gonna blow up, but I won’t find out until I watch the video
An engine tear down vid would be sick
Did that to my 450r ... It put the valves back into spec no need for tightning or further adjustment.
It would never be worth it but a real test would be on one fresh off the show room floor 😦😂
Also, the engine failing sounds and looks a lot like an angle grinder finally cutting through a piece of aluminium
Did the piston ring weld to the cylinder?
Them tape soda companies 😂 I would love to see the damage and the rebuild and the everclear
I'll bet the neighbors love you!
I would love to see a video on the rebuild!
The neighbors are probably happy
Man that was hard to watch 😂😂
This is actually so cool
Another idea full bottle of 2 stroke for a full tank 👀
I'd like to see if u put some powerful fans on the radiators etc if it would have been able to cool itself an stay pinned alot long. Seems like it basically just overheated an siezed up..
It would have lasted a lot longer but the end result would have been the same, bottom line is the motor is not designed for that kind of strain
@@kylecorbett maybe but feel like people run these bike wot all the time but with lots of air moving through the radiators, who knows tho 🤙
ngl i thought it would last like 20 sec thats pretty good ngl
😅“If you dont already know, my names Kyle…” welp no i didnt, but i coulda guessed. 😮😂
I subbed because I'm also Kyle and love 2 strokes ❤
Nice, thanks for the support 😎
How many hours on the piston before ?
Bros turning into whislin diesel
How many hours were on the bike already
can you do a video of rebuilding of the 125 and 150 after this
Rm125 still be going till this day , try all the main brands then a china brand
Thank you for switching tape sodas I sub scribed
Holy fuck this was hard to watch lol, She put up damn good fight before she gave out though that's for sure!