Why did you skip the disassembly? I have Model 9876L which has no screws showing, so I'm assuming that I have to open the casing with a knife edge, which often destroys it when you don't know exactly how it is held together.
See 14:00 onwards for re-assembly, might help you understand how it went together. So I got out of bed just to look this up, I never recorded the disassembly, there are 5 very obvious phillips screws under the lower cover. separate the silver bit from the black bit and they will be very obvious, DO NOT try to pry the whole unit apart.
@@TheAussieRepairGuy thank you for this video! I didn't think the black part was under the silver, I thought it can off to expose screws. I have the same issue, where to insert a pry tool without wrecking the clipper, while examining frame 12:52 I saw the black plastic fingers in the cutter end that cold be pried out to start the cover reveal, a pry in the lower part of the switch hole and prying out on the silver cover at the charger end got it off.
@@GmanInd Yes this video was done a few years ago and I was in a bit of a rush, and the owner was observing as I did it, consequently I missed filming a few steps.
just replaced the battery on mine and something interesting happens. After 15 minutes of charging the blue LEd switches off. How come is this happening? I''m sure it would take longer than 15 minutes to recharge a battery. Any ideas? Cool video by the way, it is very helpful.
@@TheAussieRepairGuy you could be right, it was partially charged I fully discharged it. Still, something is off. The motor might not be working that well as the change of battery didn't seem to help that much, it feels slower and rotating at a lower frequency than my new Wahl Beret.
Sounds like retaining clip. I don't have these in my posession anymore, and I'm not an expert on them. My suggestion would be to assemble the unit until it becomes obvious where that part belongs.
Probably because these had been in my hands for a total of 5 minutes at the time. Why don't you make your own video where you cover these points yourself?
![Best Nose Hair Trimmer 2024 [don’t buy one before watching this]](http://i.ytimg.com/vi/F2yenLfYdV0/mqdefault.jpg)
Друг спасибо тебе. Благодаря твоему видео понял почему у меня вибрирует вал. Ох уж этот магнит!!!
Да, допуски довольно близки.
I was looking to change the battery in a different clipper, but I have these ones too, so will save this video for when they die.Thanks!
Çok faydalı video olmuş teşekkür ederim kardeşim
Awesome vid. Thanks.
What temp u run ur soldering iron at?
About 400c, and I use 60/40 tin lead flux core solder, 1mm diameter.
Why did you skip the disassembly? I have Model 9876L which has no screws showing, so I'm assuming that I have to open the casing with a knife edge, which often destroys it when you don't know exactly how it is held together.
See 14:00 onwards for re-assembly, might help you understand how it went together.
So I got out of bed just to look this up, I never recorded the disassembly, there are 5 very obvious phillips screws under the lower cover.
separate the silver bit from the black bit and they will be very obvious, DO NOT try to pry the whole unit apart.
@@TheAussieRepairGuy Will do. Thanks for the reply.
@@TheAussieRepairGuy thank you for this video! I didn't think the black part was under the silver, I thought it can off to expose screws. I have the same issue, where to insert a pry tool without wrecking the clipper, while examining frame 12:52 I saw the black plastic fingers in the cutter end that cold be pried out to start the cover reveal, a pry in the lower part of the switch hole and prying out on the silver cover at the charger end got it off.
@@GmanInd Yes this video was done a few years ago and I was in a bit of a rush, and the owner was observing as I did it, consequently I missed filming a few steps.
just replaced the battery on mine and something interesting happens. After 15 minutes of charging the blue LEd switches off. How come is this happening? I''m sure it would take longer than 15 minutes to recharge a battery. Any ideas? Cool video by the way, it is very helpful.
It could be that the newer battery is alreasy partially charged. New batteries iften need to be discharged a couple of times to reach design capacity.
@@TheAussieRepairGuy you could be right, it was partially charged I fully discharged it. Still, something is off. The motor might not be working that well as the change of battery didn't seem to help that much, it feels slower and rotating at a lower frequency than my new Wahl Beret.
@@miguelfernandes333 perhaps a small drop of sewing machine oil on motor shaft bushings
On Jaycar, I could find the following battery: 14500 Rechargeable Li-Ion Battery 800mAh 3.7V Solder Tag
Is that the correct one?
Yes, a highee capacity is fine as long its the 14500 size.
Please tell me what battery you used. If you have a link to purchase, even better
14500 size 800ma li-ion with solder tqbs.
What is the battery size and where can I get one? I have the sterling mag but can’t find the battery!
At 4:50 I state that its a "14550" which is the type of li-ion cell.
Yeah but you don't show how to open it
I'll go back over this when I'm not 300km from home, and see if I can elaborate. However I don't own this, nor is it in my posession now.
Off memory, I just undid screws and popped the snap clips on the body.
👍
U know that annoying aluminum shaped like a U once you open up the blade? It fell out. But, now I don’t know where it goes?
Sounds like retaining clip. I don't have these in my posession anymore, and I'm not an expert on them. My suggestion would be to assemble the unit until it becomes obvious where that part belongs.
@@TheAussieRepairGuy you have a wahl mag, right?
@@or1946 no this was handed to me for battery replacement - I did the video and gave it back to its owner.
@@TheAussieRepairGuy ok. Damn, I wish I knew how to put it back. It’s so Frustrating ( it’s for a Wahl Mag Trimmer ) Anyone know?
@@or1946 this guy seems to go into detail that might help:
czcams.com/video/lRwPczjHqEE/video.html
Wahl. Ka. Tirimr. Silo hogeua. Kru
Why you don't describe the real problem. The contact was broken or bad. Typical Wahl. All those Beret pro trimmers has the same problem.
Probably because these had been in my hands for a total of 5 minutes at the time.
Why don't you make your own video where you cover these points yourself?
Such annoying skills
I'm glad I don't exist just to entertain you.