Mercedes Benz C Class SAM Unit Diagnose and repair [Part 2]
Vložit
- čas přidán 6. 12. 2022
- In this video I'm going to show you how to Mercedes Benz C-Class signal acquisition module [SAM] Unit Diagnose and repair
Part 1 video link please find below
• Mercedes Benz C Class ...
#mercedes #mercedescclass #mercedescclasssamunit #mercedessamunit #mercedessamunitrepair
#mercedessignalacquisitionmodule #mercedeswipersnotworking #mercedesindicatorsnotworking #mercedeselectricwindowsnotworking #instrumentclustersnotworking #mercedesblinkersnotworking #mercedessamremoval
#thefix
Hi
Thank you for the follow up. I would have inspected the sam unit under a microscope. Might have some tracks damaged.
Nice job appreciate the videos
excellent job
Helpful
Take the SAM out...before it goes damp & spray it with PCB lacquer....+ add silica desiccant bags in the box...also seal the enclosure with silicone gasket....to keep water out....also can you tell me how I can get the software on my phone...like you have on your phone...I need to diagnose + clear faults...thxs
Thanks for the video. Just curiosity, what is the second hand price of the SAM unit, and the price new?
YOU HAVE MY aBO THANKS! One Question i have a w203 c270cdi year 2001 automatic -my Problem is its only lightining ESP(but when i drive it goes and when standing longer 3-4 hours example in the mornig when i start i comes again) and my Wheel is to hard like without servo i read it with delphi ds150 and i have also SAM front error codes with AC errors "aircondition pressure sensor and like this permanent -but everything work in my car heater windows signal is all ok???Thank you i need your help!
Hi, see if there is a loose connection in the abs wiring and sensors
Hello! I've come to the conclusion that my sam module has gone bad. I've lost a lot like your car did. I still have function of my cluster and windows. I also still have my turn signals come on in the cluster. What I've got going on though is a loss of my front blinkers the ones in the trim and in the headlight housing. I've lost windshield wipers. I have low brake fluid light on. My brights indicator stays on even though the lights aren't working. Well I do have the driver side headlight. Also my parking brake light stays illuminated. Even my ats shows a reading of 185 degrees( It's brand new, I just installed it before I parked it). I park my mercs over the winter. Which they sit outside, I assumed water got into the sam unit. Upon inspection I didn't see any corrosion, the board itself does have some very faint water marks on it. There is a few spots with very light discoloration. Nothing like you've shown in your video though.
Hi, you can try cleaning it up and putting it back in. Sometimes, it works.
@thefix9823 Thank you for the reply! After looking at the board for a good 45 minutes I did find a burn mark. I don't know how I didn't see it prior. It is pretty sizeable, I'd say. That's definitely my issue, thank you again!
good morning
if the front sam has the same reference, the same Hw /Sw ; Would you need some kind of programming for the car? Or would it just replace the new one with the old one,
Thanks
Hi, it should just work without any programming.
Helle
I have changed the front sam for another with the same references and the same hw and sw, it works fine but the reverse lights come on when I start the car.
I would like to know if you have ever had this problem. it's a mercedes 203 from 2004.
thank you .
Hi, It should work without any programming
Did the new SAM module required programming? Or was it a Plug and Play solution ok?
Hi it was plug and play
How much you paid for the used SAM unit?. The cover for SAM module is a bit filmsy. Plus your car looks likeit is always parked outside. Great if there is a way to improve the original top cover. Regards.
Hi please, which diagnostics did you use? thanks
Hi, I used Thinkdiag
My w203 has these issues. When i turn on the engine, the coolant fan comes on violently , the ac controls stop working, the windows dont work, dash lights are off. All these things work when the engine is off. From the video i might need a sam replacement.
What if my car wont start? technician told me it was my front sam.
Please I have a question I have Mercedes w211/2 2007 , if I change the front sam unit do I need to reprogramming or not ?? Thank you very much
Hi have not done one of them but I think you dont have to programme it but totally sure
Not totally sure
I have a 2005 c230 kompressor and the left front turn signal stays on. is that a signal relay problem?
Hi, it might have the relays built-in to the sam unit one for left and one for right if it was a single relay somewhere both the turn signals would have the same problem,but to find out for sure you need to look at a wiring diagram to see how the system works.
I have same problem. I have a 2005 c230 and my right turn signal bulb stays on all time.
Sir,
Where did you find a replacement sam2? I have a 06 R500 with a bad Sam 2, scanned the QR code and nothing found on internet. QR is 146160053180121 but the number on the motherboard etched is 28013293. Please help if you can.
Hi, i would try and find you one is there any other numbers on it and also send me a photo
@@thefix9823 I thank you for your help sir.
QR sticker : 28041416 REAR SAM
QR Code scanned: 14160053180121
Burned Chip : 6143D - AA537 M
Motherboard factory #: 28013293 C BS
Inked stamped on motherboard:E033
Etched NYKS NM4 94V-0 -- NDN137 2B-11 256 511
REAR SAM CASE:
ZB A 164 540 29 62
HW A 164 545 95 32 Q01
SW A 164 442 18 00
Delphi part # 28041416
HW 28/05 SW 35/05 SNO:121 DOP:320/05
Here's a link for the part
www.ebay.co.uk/itm/175434140882?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=P8H2vhqXRvu&sssrc=2349624&ssuid=GHsdcpGiR5C&var=&widget_ver=artemis&media=COPY
And your OBD2 to delete srs on androi phone.
What is model that obd2?
Sent photo to me plese.
Hi it's a thinkdiag
8
excellent job