Thanks Manuel for this great little rig and this video! I already tried this a few weeks ago, and it works fine on win10 with wsjt-x. I had FT8-QSOs with USA and Brazil (8000km) with only 3,5-4,5W (got it pre-assembled and only get 3,5W on 20m, probably have to tune it). I also had it running on Linux (Ubuntu20.4) but i gave it up there, because wsjt-x has problems there with the TS-480 config selection. I found out switching between yaesu-817 and TS-480 helps, but i have to do this several minutes until it finally randomly works. 73, DC8CB
I´m not a Linux Guy, but Guido helped me out: in linux, you need to set the right COM port properties so that DTR does not keep flipping. From a terminal run: stty -F /dev/ttyUSB0 raw -echo -echoe -echoctl -hupcl -echoke 38400
I'd find it very convenient if it was possible to disable PTT in software, so I wouldn't need a special cable. But such a nice little radio, thanks for all!
I have the exact same settings. I have the driver installed from your web page. My PC recognizes the device under ports COM CH340. When I push "Test CAT" the radio clicks, powers off and back on. CAT test fails. What am I doing wrong? I've tried multiple PCs. Multiple cables. Multiple USB hubs. COM 5 is the truSDX and COM 3 is my digirig sound card on my system.
There are adapters that let users get the mike/speaker from an iPhone. Is there any digital-mode software that works with iPhones (or Android phones) and gives CAT plus the digital modes. The combination would be far more portable than any system involving a laptop. And echoing that tiny (tru)SDX screen on an iPhone would be marvelous for those of us with aging eyes.
Vielen Dank für das Video und für die Entwicklung des (tr)uSDX. Ich habe seid Wochen probiert den (tr)uSDX an meinem Linux-System ans laufen zu bekommen, allerdings nur mit Problemen. Die CAT Steuerung hat sich nicht stabil aufgebaut. Beim meinem Windows-System war es kein Problem. Durch dein Video ist mir aufgefallen das beim Linuxrecher die Felder „Force Control Lines“ nicht ausgefüllt waren. Nachdem ich diese richtig eingestellt habe läuft es endlich Problemlos. Noch mal vielen Dank, ohne das Video hätte ich das wohl niemals gefunden. VY 73 de Peter; DL2PK
Thank you for the video. I just got my assembled trusdx a few minutes ago and trying to get started. ALL my computer control panel settings are at maximum for my speaker audio volume according to several videos telling how to get high volume audio from my computer. Although there's a lot of videos I can hear even when I turn down the video volume control I still can't hear this video. Ooooohhhhh All the advertisements attached your video I can hear really good. Is there a video on the trusdx that's recorded a lot louder? Thank you.
Hello I purchased ur tr usdx assembled from the Chinese vendor and noticed the tranceiver has a noticeable hum on 20 meters he sent me a new top board . I installed it and it still has a hum . Quite loud . Do not know what to do next. Any advice ? I would love to that great tranceiver for backpacking . Thanks. Rodney. Ki6pxv
Hi ! First of all, i want to thanks you for all the good work and your effort in this project. I really apréciate. I have some problem to configure cat in my raspberry pi. Not working in wsjtx and half working via flrig. Help me please !!
From one comment below, I took the following: I´m not a Linux Guy, but Guido helped me out: in linux, you need to set the right COM port properties so that DTR does not keep flipping. From a terminal run: stty -F /dev/ttyUSB0 raw -echo -echoe -echoctl -hupcl -echoke 38400
Team, just join the forum but I going to ask here, I had tried to follow the set up as you describe but it does not want to give me the green light ....it does key the radio when try to test but never goes green and give me an error about Omni-rig or timed.out while connecting to radio....it does work perfect with Winlink settings but not for JT8 or JS8Call.....what I am missing???? Using windows laptop
Unfortunately I´m not an expert in CAT Communication. I have no clue why some apps work and some not. But if you use the search function in my forum, you can find a lot about CAT from way more skilled people then me. 73 Manuel; DL2MAN
Hello Manuel, Thank you for a good device and video. I have a question: What if I use standard unmodified aux cable? Will there be any problem getting (tr)uSDX on the air? I've seen couple other videos recently and people there are using aux cables which look unmodified, can you confirm this opportunity? I am going to use this Tx with FT8cn on android.
In Direwolf, the options to use PTT are RTS or DTR. Would these work with the signals that (tr)uSDX is sending to the COM port? Which one would I use? Or should I just use VOX? What I'm trying to do is operate APRS on the 30m band. I don't know whether I can do that successfully with only 5w, but let's see. I was in a discussion with the operator of an I-gate in Seattle who received my APRS signals sent from Utah with a 10w radio and he said that they were pretty weak. Maybe I'm going to have to use Robust Packet.
I have no clue, what direwolf is, but CW can be triggered by RTS (independent from key line). For PTT (on any other mode but CW) you should use CAT Command. 73 Manuel; DL2MAN
@@dl2man Direwolf is an APRS software modem. It sends and decodes AX.25 packets through a computer sound card. It can use VOX, but the radio needs to have a fast circuit for this. PTT is best. 73 de K7DMJ
@@dangermandave67 check the direwolf user manual, section 9.2.9.4 for setting up PTT using hamlib. hamlib acts as a middleman to send the CAT commands to the radio and direwolf will use it instead. Looks like the model ID for a Kenwood TS-480 is 2028. Hope that helps.
Thank You Manuel! Will there be an opportunity to illustrate how to use FLDIGI for Other digital modes… RTTY, PSK, CW etc… Will there be Mode and filter CAT commands available? 73
Hi Frank, Setting up FLDigi follows the same pattern as shown in this Video. In Fact I´m running that with (tr)uSDX anyway. Don´t know if a new Video will be made for that. Mode changes already work (MD cmd), and yes a subset of DSP filters can be added (SH/SL cmd). But I cannot give any timing for that. 73 Manuel; DL2MAN
I cant get cat to work I have installed driver ch340 but it does not recognize the (tr)uSDX when plugged in. Can anyone suggest how to fix this. Receiving all sorts of signals on WSJX. Would like to be able to complete setup!
Sometimes Windows block comports and hides it. In your device manager set it to "show hidden devices" and see if there´s any hidden com ports. If so: Uninstall them, restart your computer and try again. Make sure, you use only the CH340 driver linked on my Firmware page. We also saw problems with newer/older Versions. If you still can´t solve it, join my forum.dl2man.de and post your issue in the troubleshooting section. I´m sure you´ll get a lot of suggestions. 73 Manuel; DL2MAN
@@dl2man yes I’ve seen it prior to asking and it didn’t quite work, though I can’t rule out user error. I hear the clicks on the relays but it does not change bands and throws a communication error
If I had just one combined Jack, I would make myself one cable. This would make things even easier..... I´d buy such a cable: www.amazon.de/Goobay-50467-Headset-Adapter-4-pol-Schwarz-Gr%C3%BCn-Rot/dp/B007N5Z3UW cut of the Female Sockets and solder male connectors instead....
@@denislacroix654 Cutting the center Pin away was just for convenience / safety, so nothing touches accidently the solder flag. If you remove it or not is up to you, however: It must not be connected other than shown in the Video. In one sentence: In your case, the Laptop Side changes, the (tr)uSDX Side stays exactgly the same....
Hi Doug, in the Video, you saw me setting up the rig for WSJTX. Switch WSJTX to Mode WSPR and you´re good to go. Or are there any more specific questions ? 73 Manuel; DL2MAN
@@diegogarciamedina6363 No ! Never change the Fet without adjusting the class E Network. Fet is part of the class E Network. If you just swap fets, you will most likely get no efficiency and bad harmonic suppression.
@@jameslee522 I´ve tested it, and it works. In Vara HF -> Radio Setup, use "Kenwood Amateur", Mode USB, Radio Control Port use your Com Port, Baud 38500, NO Enabling RTS and DTR, PTT Port chose Kenwood TS590S. Before trying, make sure, your Reference frequency is calibrated, and carefully adjust Input and output levels of Soundcard vs Volume of (tr)uSDX. I´ve just sent an E-Mail with (tr)uSDX and 5W over the 40m Band to myself and Guido.... Good to know, we can even send Mails when Local Internet is gone or Power is out. 73 Manuel; DL2MAN
I apologize for the disorder Mr. Guido I have a problem with my radio who is marked with his name. I wanted to ask her why my radio does not transmit, the backbone does not exist and consequently does not put an antenna tuner. It is enough for me that it gives me a little advice to solve this problem or if by chance it has an email where it can send the problem in detail. I thank you so much and for now I greet you. Thanks Alberto
I watch a lot of these videos and I can't wait to buy one of these little guys.
Thanks Manuel for this great little rig and this video!
I already tried this a few weeks ago, and it works fine on win10 with wsjt-x. I had FT8-QSOs with USA and Brazil (8000km) with only 3,5-4,5W (got it pre-assembled and only get 3,5W on 20m, probably have to tune it).
I also had it running on Linux (Ubuntu20.4) but i gave it up there, because wsjt-x has problems there with the TS-480 config selection. I found out switching between yaesu-817 and TS-480 helps, but i have to do this several minutes until it finally randomly works.
73, DC8CB
I´m not a Linux Guy, but Guido helped me out: in linux, you need to set the right COM port properties so that DTR does not keep flipping. From a terminal run: stty -F /dev/ttyUSB0 raw -echo -echoe -echoctl -hupcl -echoke 38400
I'd find it very convenient if it was possible to disable PTT in software, so I wouldn't need a special cable.
But such a nice little radio, thanks for all!
Just found your channel.
Great stuff! Subbed
Thank You I did purchase the radio and it is a work of art very professional and i enjoy you videos Jim K4YNA
I have the exact same settings. I have the driver installed from your web page. My PC recognizes the device under ports COM CH340.
When I push "Test CAT" the radio clicks, powers off and back on. CAT test fails. What am I doing wrong? I've tried multiple PCs. Multiple cables. Multiple USB hubs. COM 5 is the truSDX and COM 3 is my digirig sound card on my system.
Any luck? I'm having same problem.
I got it working. Had to set COM rate to 115200 in Device Manager and in the program I was using (JS8Call).
Thanks Manuel! Your guys little rig just keeps being amazing! 73 - KF6IF
Cannot wait to get on the air using FT8!
Thanks
There are adapters that let users get the mike/speaker from an iPhone. Is there any digital-mode software that works with iPhones (or Android phones) and gives CAT plus the digital modes. The combination would be far more portable than any system involving a laptop. And echoing that tiny (tru)SDX screen on an iPhone would be marvelous for those of us with aging eyes.
forum.dl2man.de/viewtopic.php?p=3322#p3322
Vielen Dank für das Video und für die Entwicklung des (tr)uSDX. Ich habe seid Wochen probiert den (tr)uSDX an meinem Linux-System ans laufen zu bekommen, allerdings nur mit Problemen. Die CAT Steuerung hat sich nicht stabil aufgebaut. Beim meinem Windows-System war es kein Problem. Durch dein Video ist mir aufgefallen das beim Linuxrecher die Felder „Force Control Lines“ nicht ausgefüllt waren. Nachdem ich diese richtig eingestellt habe läuft es endlich Problemlos. Noch mal vielen Dank, ohne das Video hätte ich das wohl niemals gefunden. VY 73 de Peter; DL2PK
Welche Linuxprogramme nutzt du?
@@pascalm.1237 Fedora und Linux Mint.
OK. Aber welche Linuxprogramme nutzt du im speziellen? Nutzt du WSJT-X? Welchen Linux-Logger? N1mm läuft ja nicht unter Linux.
Do you not use any hardware interface and just connect both jack cables directly to the computer?
As mentioned in the Video: directly connected ! Dangerous, but: No Risk, no fun ! 73 Manuel; DL2MAN
Thank you Manuel.
i've got comunication error with rig / connection rig is broken when connect my rig to ft8cn via CAT
So cool...
Thank you for the video. I just got my assembled trusdx a few minutes ago and trying to get started. ALL my computer control panel settings are at maximum for my speaker audio volume according to several videos telling how to get high volume audio from my computer. Although there's a lot of videos I can hear even when I turn down the video volume control I still can't hear this video. Ooooohhhhh All the advertisements attached your video I can hear really good. Is there a video on the trusdx that's recorded a lot louder? Thank you.
Try this for comparison: czcams.com/video/PydB0b37Ibo/video.html I started using external microphone with the "NVIS" Video... 73 Manuel; DL2MAN
For the transceiver settings is it just SSB and USB for digital modes?
Hello I purchased ur tr usdx assembled from the Chinese vendor and noticed the tranceiver has a noticeable hum on 20 meters he sent me a new top board . I installed it and it still has a hum . Quite loud .
Do not know what to do next. Any advice ?
I would love to that great tranceiver for backpacking .
Thanks.
Rodney. Ki6pxv
You might want to watch this: czcams.com/video/ijQKpjToHFw/video.html
Hi ! First of all, i want to thanks you for all the good work and your effort in this project. I really apréciate.
I have some problem to configure cat in my raspberry pi. Not working in wsjtx and half working via flrig.
Help me please !!
From one comment below, I took the following: I´m not a Linux Guy, but Guido helped me out: in linux, you need to set the right COM port properties so that DTR does not keep flipping. From a terminal run: stty -F /dev/ttyUSB0 raw -echo -echoe -echoctl -hupcl -echoke 38400
Team, just join the forum but I going to ask here, I had tried to follow the set up as you describe but it does not want to give me the green light ....it does key the radio when try to test but never goes green and give me an error about Omni-rig or timed.out while connecting to radio....it does work perfect with Winlink settings but not for JT8 or JS8Call.....what I am missing???? Using windows laptop
Unfortunately I´m not an expert in CAT Communication. I have no clue why some apps work and some not. But if you use the search function in my forum, you can find a lot about CAT from way more skilled people then me. 73 Manuel; DL2MAN
Do you have a video using Digirig? I can’t get it to work. Thank you
No, never used Digirig. Sorry. 73 Manuel; DL2MAN
Hello Manuel,
Thank you for a good device and video. I have a question: What if I use standard unmodified aux cable? Will there be any problem getting (tr)uSDX on the air?
I've seen couple other videos recently and people there are using aux cables which look unmodified, can you confirm this opportunity?
I am going to use this Tx with FT8cn on android.
I think, I´ve answered your question in the Video.... 73 Manuel, DL2MAN
In Direwolf, the options to use PTT are RTS or DTR. Would these work with the signals that (tr)uSDX is sending to the COM port? Which one would I use? Or should I just use VOX? What I'm trying to do is operate APRS on the 30m band. I don't know whether I can do that successfully with only 5w, but let's see. I was in a discussion with the operator of an I-gate in Seattle who received my APRS signals sent from Utah with a 10w radio and he said that they were pretty weak. Maybe I'm going to have to use Robust Packet.
I have no clue, what direwolf is, but CW can be triggered by RTS (independent from key line). For PTT (on any other mode but CW) you should use CAT Command. 73 Manuel; DL2MAN
@@dl2man Direwolf is an APRS software modem. It sends and decodes AX.25 packets through a computer sound card. It can use VOX, but the radio needs to have a fast circuit for this. PTT is best. 73 de K7DMJ
@@dangermandave67 check the direwolf user manual, section 9.2.9.4 for setting up PTT using hamlib. hamlib acts as a middleman to send the CAT commands to the radio and direwolf will use it instead.
Looks like the model ID for a Kenwood TS-480 is 2028.
Hope that helps.
Thank You Manuel!
Will there be an opportunity to illustrate how to use FLDIGI for Other digital modes…
RTTY, PSK, CW etc…
Will there be Mode and filter CAT commands available?
73
Hi Frank, Setting up FLDigi follows the same pattern as shown in this Video. In Fact I´m running that with (tr)uSDX anyway. Don´t know if a new Video will be made for that. Mode changes already work (MD cmd), and yes a subset of DSP filters can be added (SH/SL cmd). But I cannot give any timing for that. 73 Manuel; DL2MAN
Has any one used this radio with an android tablet? Just ordered the radio and plan on using it for digital modes mainly.
Adam, K6ARK has a Video about that online.
I cant get cat to work I have installed driver ch340 but it does not recognize the (tr)uSDX when plugged in. Can anyone suggest how to fix this. Receiving all sorts of signals on WSJX. Would like to be able to complete setup!
Sometimes Windows block comports and hides it. In your device manager set it to "show hidden devices" and see if there´s any hidden com ports. If so: Uninstall them, restart your computer and try again. Make sure, you use only the CH340 driver linked on my Firmware page. We also saw problems with newer/older Versions. If you still can´t solve it, join my forum.dl2man.de and post your issue in the troubleshooting section. I´m sure you´ll get a lot of suggestions. 73 Manuel; DL2MAN
I’m having trouble getting this to work on my MacBook. Any suggestions on how to get it to work on MacOS?
Guido has added some links on my manual site regarding Mac: dl2man.de/4-trusdx-manual/
@@dl2man yes I’ve seen it prior to asking and it didn’t quite work, though I can’t rule out user error. I hear the clicks on the relays but it does not change bands and throws a communication error
CAT control are with USB?
Thanks Manuel! Both my pcs only have one jack…. For audio and Mike. Yours has 2 jacks, one for audio,the other for Mike. Any suggestions? 73
You might want to try a USB soundcard. Inexpensive on eBay. 73
There are adapters available. Search for "trrs splitter".
If I had just one combined Jack, I would make myself one cable. This would make things even easier..... I´d buy such a cable: www.amazon.de/Goobay-50467-Headset-Adapter-4-pol-Schwarz-Gr%C3%BCn-Rot/dp/B007N5Z3UW cut of the Female Sockets and solder male connectors instead....
@@dl2man do I still have to cut away one of the wires from the male plug?
@@denislacroix654 Cutting the center Pin away was just for convenience / safety, so nothing touches accidently the solder flag. If you remove it or not is up to you, however: It must not be connected other than shown in the Video. In one sentence: In your case, the Laptop Side changes, the (tr)uSDX Side stays exactgly the same....
Could you post a video of setting this radio up on WSPR?
Hi Doug, in the Video, you saw me setting up the rig for WSJTX. Switch WSJTX to Mode WSPR and you´re good to go. Or are there any more specific questions ? 73 Manuel; DL2MAN
Does this radio have a built-in battery?
No, not internal, but there´s external Battery Options: czcams.com/video/nnGz_6oPKr0/video.html
Hi, is it possible to receive audio rx by cat streaming from transceiver to pc? (no red audio cable used) thanks
Not at this point, no. Guido is still trying to implement it, but we ran out of memory. 73 Manuel; DL2MAN
@@dl2man thank you, 73´s good dx LU2DVY
@@dl2man using mrf150 or another rf mosfet in the finals shold increase output power near to 10 Watts in 15 meters? thanks
@@diegogarciamedina6363 No ! Never change the Fet without adjusting the class E Network. Fet is part of the class E Network. If you just swap fets, you will most likely get no efficiency and bad harmonic suppression.
@@dl2man great advice, It seems that is carefully designed as is it is now. thanks
Hi Manuel!, Planst du auch eine Version mit 15m ? Habe da mal was gehört aber noch nichts gefunden.
dl2man.de/2-trusdx-assembly/ (runter scrollen).... Es wird bald vorbereitete Platinen für "Classic" und "Hi Bands" geben. 73 Manuel; DL2MAN
Can we also use VOX to transmit?
Yes, can be used as well. But CAT seems way more elegant and definate to me.
@@dl2man Thanks!
could this be used for winlink email?
Good question. I would assume yes, but I have never used WinLink. So I will try it.... 73 Manuel; DL2MAN
@@dl2man awesome!
@@jameslee522 I´ve tested it, and it works. In Vara HF -> Radio Setup, use "Kenwood Amateur", Mode USB, Radio Control Port use your Com Port, Baud 38500, NO Enabling RTS and DTR, PTT Port chose Kenwood TS590S. Before trying, make sure, your Reference frequency is calibrated, and carefully adjust Input and output levels of Soundcard vs Volume of (tr)uSDX. I´ve just sent an E-Mail with (tr)uSDX and 5W over the 40m Band to myself and Guido.... Good to know, we can even send Mails when Local Internet is gone or Power is out. 73 Manuel; DL2MAN
@@dl2man awesome! This looks like a cool little radio. Plan on getting soon!
Уважаемый вот бы по русски хоть пару слов. Технические термины непонимаю.
too complicated
I apologize for the disorder Mr. Guido I have a problem with my radio who is marked with his name. I wanted to ask her why my radio does not transmit, the backbone does not exist and consequently does not put an antenna tuner. It is enough for me that it gives me a little advice to solve this problem or if by chance it has an email where it can send the problem in detail. I thank you so much and for now I greet you. Thanks Alberto
Please join forum.dl2man.de and explain the problem. There are plenty of people, that will help you.