Question : Can Multiple Outputs Works At Once? Say 1&2 Outputs For The Nitrous Single Stage Solenoids Wired For AFR Control Loop With A MAP Progression And Then Can Output 3 Also Be Used At The Same To Ground A Relay On Or Off Based On Vehicle Speed Input Say Additional Cooling Fans (To Make Fans Turn Off Past 30MPH)? AND Could I Have Output 4 Ground Another Relay Based On MAP Pressure Setting? I Would Like All Outputs To Operate Simultaneously. Is This Possible?
Yes, multiple outputs can be enabled at the same time, as long as your output setups were all the same all would come on at the same time. Yes, outputs 3 and 4 will send signal to a relay without the need for an additional driver, as the relay would be handling the amp draw from whatever accessory you are activating.
I just bought a nitrous express system with the Max 5 and I can’t find any instructions on wiring the bottle heater and the nitrous sensor to the max 5 to use heater control I need help !
@@Jtdedeaux Why do you need to complicate things? You can set the ramp to reduce power and restart the ramp if you're TPS drops below a certain percentage.
Question On The Retard Output. If I Set It To Enable At Any Point On My Curve Does The Curve Have To Be Active Or Does It Operate Completely On That Curve Type Input. Say I Have My Curve Set To Pressure From 0PSI - 15PSI (100%->0% Progression): Will The Retard Signal Be Sent Out If Set To 5PSI And The The Boost Pressure Is 10PSI BUT While The Throttle Position Is Below Activation Point Of The Curve?
The retard signal is sent by a user defined point in the solenoid progression ramp, not by the ramp type. So for example if you put the start point at 30 that means at 30% solenoid progression it will send the retard signal out.
@@NitrousExpressVids Ok I Get That But Does The Retard Output Only Occur While When Curve Is Active? The Retard Out Will Not Output If Input Parameters Are Not Met?
@@NitrousExpressVids ok sounds good thank you! because im trying to get a smoother and faster activation so i was trying to see what hertz was recommended
Great video ..
Nice video make more videos
Question : Can Multiple Outputs Works At Once? Say 1&2 Outputs For The Nitrous Single Stage Solenoids Wired For AFR Control Loop With A MAP Progression And Then Can Output 3 Also Be Used At The Same To Ground A Relay On Or Off Based On Vehicle Speed Input Say Additional Cooling Fans (To Make Fans Turn Off Past 30MPH)? AND Could I Have Output 4 Ground Another Relay Based On MAP Pressure Setting? I Would Like All Outputs To Operate Simultaneously. Is This Possible?
Yes, multiple outputs can be enabled at the same time, as long as your output setups were all the same all would come on at the same time.
Yes, outputs 3 and 4 will send signal to a relay without the need for an additional driver, as the relay would be handling the amp draw from whatever accessory you are activating.
I just bought a nitrous express system with the Max 5 and I can’t find any instructions on wiring the bottle heater and the nitrous sensor to the max 5 to use heater control I need help !
We have instructions on nitrousexpress.com and we also have a tech line available from 9am-5pm CST at 1-888-463-2781
Can I use both RPM based and TPS based ramping? say I want to ramp rpm at low end, and then be able to pedal throttle at high rpm
No sir, it will only be one or the other. The controller will not allow for ramp type to be changed mid-ramp.
@@NitrousExpressVids but you can use the rpm based ramp and a tps window switch combined correct?
@@Jtdedeaux Why do you need to complicate things? You can set the ramp to reduce power and restart the ramp if you're TPS drops below a certain percentage.
Question On The Retard Output. If I Set It To Enable At Any Point On My Curve Does The Curve Have To Be Active Or Does It Operate Completely On That Curve Type Input. Say I Have My Curve Set To Pressure From 0PSI - 15PSI (100%->0% Progression): Will The Retard Signal Be Sent Out If Set To 5PSI And The The Boost Pressure Is 10PSI BUT While The Throttle Position Is Below Activation Point Of The Curve?
The retard signal is sent by a user defined point in the solenoid progression ramp, not by the ramp type. So for example if you put the start point at 30 that means at 30% solenoid progression it will send the retard signal out.
@@NitrousExpressVids Ok I Get That But Does The Retard Output Only Occur While When Curve Is Active? The Retard Out Will Not Output If Input Parameters Are Not Met?
@@salvatorehayes2753 that is correct.
at what point would you consider a solenoid as "trash can solenoid "
.157 or larger.
@@NitrousExpressVids ok sounds good thank you! because im trying to get a smoother and faster activation so i was trying to see what hertz was recommended