Mercedes Benz CDI W204, W207 OM651 Engine Fuel Injector Seal Replacement Part One Of Two
Vložit
- čas přidán 30. 09. 2021
- In this guide you will learn how to replace fuel injector seal on C, E models Chassis W204, W207 with Engine OM 651.911.
This task is carried out in TWO parts, this is part one of two, access to part two can be obtained by clicking on the link given below.
Disclaimer:
this video only contains tips and recommendations that could be useful when carrying out vehicle repairs or replacement parts, STANHOPE AUTO REPAIR CENTRE WARDAK is not liable for any damage, harm injury or property damage incurred while carrying out repairs or replacement that are a result of incorrect use or misinterpretation of the provided information purposes only and does not guarantee achievement of specific result. The user is personally liable for incorrect use of repair equipment, tools or vehicle parts, in particular, when this use poses the risk of injury. STANHOPE AUTO REPAIR CENTRE WARDAK strongly recommends being careful and adhering to the safety rules when doing any repair or replacement. - Auta a dopravní prostředky
Thank you the video was perfect..
Thanks for watching our channel ☺️
THANKS
Thanks for watching our channel
Hey, are the injectors different between the OM 651 913 and the OM651 912? Between the c180 cdi and c200? W204 2012. Thnx
👍👍👍professionnel
Thanks for watching our channel
Hey, the injectors from the OM651913 and the OM651912 are differend? W204 c180 cdi and c200cdi w204 2012. Thnx
that timing chain sounded very loose
Cool
Thanks for watching our channel 😊
Hello again! I have another question. I left my injector to a diesel specialist to check if its in good condition and its been a week and i called him up and he said he found metal shavings inside the injector. I don't know wether to trust him because the car starts but considering i accidentally poured adblue in the wrong tank so it sounds very bad when i start it. I checked with OBD it says in form of Cylinder 1 unbalanced. I empted the tank and flushed the fuel system with biocide. Now my question is, if i order a used piezo injector does it matter in what cylinder it goes in as long as it looks excatly the same? I have never messed with injectors before
Yes, you can do that, but you need to put the new injector (Injector Quantity Adjustment Code) in the ECU.
Hello, but what size is the bent key you use to rotate the injectors a little before removal (min. 13:26)? 17mm? Thanks
17mm but very gentle, Not too much force
@@stanhopeautorepaircentrewardak Perfect! Thank you so much friend, now all that remains is to build the key as I think you did
@@stanhopeautorepaircentrewardak why not to much force?
Thank you, was that injector 3 you were working on?
Thanks for watching our channel
Yes, it was, I think.
on my om651 i have puddles in these holes 1:57, this means my injectors are leaking? (when standstill i sometimes feel misfires)
Thanks for watching our channel.
If you smell exhaust smoke around the injector or a shiny black carbon is built around the injector, then this could be 100% the case that your injector seal is leaking.
I assume the same engine is in w205 220. Altough i wonder what end does the injector 1 lie in? Front or back?
Thanks for watching our channel.
Front of the engine
@@stanhopeautorepaircentrewardak thank you!
What is the tool called you use to remove the fuel line at 8.28? And tool at 13.27?
Thanks for watching our channel
For injectors fuel line removal: BGS 8450 | Pipe Wrench Set, open | 12.5 mm (1/2") Drive | 14 - 17 - 19 mm amzn.eu/d/bWdnxke
For moving the injector side to side I used 17 mm snap on ventage special spanner.
@@stanhopeautorepaircentrewardak thank you for your video and time for replying!!!
können Sie bitte der namen des Diagnosegerät sagen?
Thanks for watching our channel
It is TOPDON PHOENIX PLUS DIAGNOSTIC TOOL
Vielen Dank
Wie viel zahlen Sie jährlich für Updates?
Chain gone!
Thanks for watching our channel