Video

Very very good video 👍🏻 Thank You foreman. I have the same rusty nuts in my BMW E93 on rear axles.

I'm assuming the car needs to be flat? I fail to understand how Coolant will just appear from the head and the hose with just gravity.

How did you reflash the steering rack?

Nice video. Simple repair that the dealership would charge around 2hrs labor and they will also try and tell you your ac system needs to be evac & recharged to. But as he explains it doesn’t need this due to the placement of the Schrader valve. 👍👍👍

Very informative but a long video

After I change diesel filter the car worked fine for some hours. But when turned off for some hours the diesel are "gone" from the filter. Making it impossible to start up again... Strange error

Hi there, had the same issue with my car, same car just from 2009, I've put a brand new egg valve in and cleaned everything but the engine management light keeps coming back on with the same error code, and the car feels jerky in 2nd and 3rd gear at around 2000 rpm, got the car down to the garage they erased the fault codes but about 30 mins later came back again...what's the solution

Great video thanks!

Hi, i have i40 1.7 crdi and my start stop light blinks then stays on when i start the car A with circle light, it gets the same code as on this car, also the battery is at 12.2 to 12.4 volts constant, alternator voltage is at 13.7 to 14 v. Also the light goes away and sometimes stays on

Holy crap i just removed 2 thermostat screws from my 2.0 cfgc engine yesterday without stripping anything from the engine and it takes around 2h cause its so tight there.... after watching this video i'll leave it till next weekend cause its not that easy as i thought it will 🫥 Thanks for that, otherwise i'll probably trying to replace it today and will stay without the car as is my only one now and need it to work tomorrow. Crap.

Thanks man. Nice video,good luck

How can I unlock the crash data headrest? Yes?

When torquing down the bolts/screws, you should always do it in a diagonal pattern and not sequential. That could distort the mating surfaces?

How much do you charge for a job like this one? I gotta do it and also take out intake manifold and clean it

Da li pumpa u rezervoaru treba stalno da radi ili?

I have the same car with the exact same issue fuse all look good

Excellent video sir. In my Smart fortwo 451, I don't have the oil pressure sensor either, since it probably broke when the belt was cut. Anyway, even without the sensor, in my car, the oil pressure light, It turns on and then turns off, it's no problem. I'm about to buy the sensor and I'm going to change it as soon as possible, the only problem is that they covered the hole where the sensor goes with Poxipol and I don't know how I'm going to get it out. Any suggestions? Regards

yikes ! thanks COOP ...

209 modle

Hi great video. I have the similar VW TDI 2.0 CFF engine, that have the problem of temperature only going upto 75 degrees. It now winter where I stay it takes long to warmup. I am thinking of doing this job. Does this car with a manual transmission like this one not have the 2nd thermostat like the DSG transmission?

The key scenes in the video are very good for understanding what needs to be done to remove the oil pan. Other CZcamsrs don't show scenes that show what's important. Big thanks

What happens if you don't program new codew, are we still gonna experience same problem with a car as before?

Awsome

Hi mate I did the timing belt today then I went to rotate it twice, the engine won't turn can resetting the timing fix this ? The Haynes manual did not have the timing marks for the top left one 11oclock. I used both tools for the right and bottom ones to lock them

One more question, when to put it Back, what are the stpes? Doea it need to be adjuested? Or Something like this.tx

Bro youre the best, have the same engine and i searched for this 🙏🏼

Lovely video...ive done one...not a job for the faint hearted...that electric plug on top of the gearbox is very difficult to remove....Bob...Paignton....

Was there breather issues with this car causing misfire and oil pressure

Hi what did you use here for wiring diagram. How do access the software please. Thank you

Hi i changed the fuel filter in my audi q7 engine code bug the spring came out i pushed it back in while closing and forgot to prime it car started and drove for 10mins parked it up now wont start what could be issue

Hi I have same problem do I change the whole throttle body

just sent this to my mechanic; thank you so much😁

My Peugeot 208 1.6 HDI gives 700 miles warning. But Adblue has been added and tank is full. Will I be able to continue driving past 700 miles? (had NOX sensor changed and still didn't fix the problem)

Which engine code was this car?

You always replace the water pump with the water pump housing. Usually the housing is the part that is leaking, not the pump. If you buy it original, the water pump always comes with the housing.

change cooler i have the same problem i change cooler and very good after

How to fix back pressure engine ???

Subbed

15:38

Bonjour, je voulais savoir j'avais un voyant moteur allumé sur ma audi A3 2008 140ch qui m'indiquai la pompe a eau auditionel, du coup je l'ai remplacé par une neuve et ensuite je l'est retirer avec la valise mais le voyant moteur ce remet, du coup je sais pas le problème peut venir de quoi on ma dit peut-être le relais, ou le faisceau

Hello, I replaced hp fuel pump and now get diesel right up to the hp fuel pump but can’t get diesel past the pump and to the fuel rail? Any ideas what I’ve done wrong?

If it appears after oil change, check your filter, you probably broke the stick on the filter.

Your address?

How does the metal swarf get through that dense screen? That screen looks clean, it should be clogged with the swarf as well?

Where did all those metal filings come to the fuel rail? Had the HPFP failed catastrophically?

The new revised EGR NEED TO BE PROGRAMMED!!! Just do it at the dealership. Also they have an updated intake manifold too. But they have programs that covers either or Both. This is really important!

дякую за відео все гарно розяснено

I just bought this exact car n just got done replacing my hose and new thermostat and still having low coolant issues and overheating

How did you take off the flap motor off? i trying tooo take it off but there one screw under near the lamda sensor i can not take it off

Hi can you fix this module 722.8 after repaired I got the fault 0602 Control module Continuously variable automatic transmission (CVT) is not coded. 0710 The signal from component Y3/9b2 (CVT (continuously variable automatic transmission) temperature sensor) is not available 062f Control unit Continuously variable automatic transmission (CVT) is defective.