I was "NO no no, you forgot to put the rest of the grease in the BOOT!" Haha, then you caught yourself. Great install, I need to get me some of those clamps.
Yup , that almost happened. LOL Would have sucked to remove that brand new clamp. Most likely would have ruin that new clamp trying to remove it. Thanks for checking out the video much appreciated!
On an aaannngle!!! Love it!! What a great idea using the slide hammer to remove the joint! I've always used a brass punch while my slide hammer sits lonely in the corner.😂
Oh no, lonely slide hammer sitting in the corner.. LOL Been doing it that way for years on cars at work. Thanks for checking out the video! Appreciate you dropping a comment!
Hey Shawn, Haha Yup have to be careful with the pliers be pinching a finger.LOL Yup I believe the boys are going to make our next ride trip in September. Thanks for checking out the video, my friend!
I had a popping noise in my left rear axle on my 550 several years ago. I was able to buy a complete axle off eBay for less than $40 with free shipping. It’s still working great. The price was so good that I bought another axle just to have a spare. I haven’t needed it yet but it’s there if I do need it.
That was great timing. I have a 2000 400 Big Bear that the rear Boot is bad. Other than it having Drum Brakes don't you thing it's Similar. I only use the 400 around my small Acreage. I really look forward to your Videos. The only thing is I have a Polaris General Deluxe that I ride at the LOOP & LOTO in MO. I've been to Mulberry once in 2021. It was fun, but it's 6 hours from home. The other two are around 3 & I ride with Friends. When I went to Mulberry it was a one time trip. Keep up the great Work.
Nice video! Interesting to see the inner workings of a cv axle. I've had a couple torn boots on the suburban but i just replaced the whole axle. Have fun on the next ride! We'll be wishing we were there but we'll have fun in Colorado too😎
Hey mornin Rod, yeah, lotta folks just replace the whole axle when they have a torn boot. You guys have fun at Colorado and be safe. Are you going to do any filming? Maybe post some videos from that trip?
I'm planning on taking the camera but my mic setup isn't set up right so not sure how good of video I'll get. Last time we were at mulberry in April I got just a bit of video before my camera mount broke and the audio didn't sound good so I've got some changes to do. But all my extra time has went to building my shop so haven't had a chance to mess with it yet.
I liked your video for sure, and you seem very capable and knowledgable. I would appreciate in future videos if you would let us know socket sizes as your removing everything
@@kcatv9556 . . . I passed on your video to the originator of that saying, "Bit of an aaaaangle", Big Dave from TamarackTR and told him he was famous - lol. I see he left you a comment. Nice!
Nice video! I am just now getting around to it because somehow I never got a notification. I was browsing my subscription and noticed it this way. Anyways, you made this look really easy to take off and install. I like the homemade tool for the job. Probably cheaper to make it than going to other route.
Hey buddy, yeah, that happens to me too. Don’t get my notifications. Hopefully that video will help some folks out if they ever have to do a boot on there Grizzley. Thanks for checking out the video my friend.
Hey Nathan, they are standard automotive CV boot clamp cramping pliers. I believe I picked him up at O’Reillys auto parts many years ago. Hope that helps you out, thanks for checking out the video.
I was "NO no no, you forgot to put the rest of the grease in the BOOT!" Haha, then you caught yourself.
Great install, I need to get me some of those clamps.
Yup , that almost happened. LOL
Would have sucked to remove that brand new clamp.
Most likely would have ruin that new clamp trying to remove it. Thanks for checking out the video much appreciated!
You make it look so easy, must be the clean shop.💯
Thanks, appreciate you checking out the video!
On an aaannngle!!! Love it!! What a great idea using the slide hammer to remove the joint! I've always used a brass punch while my slide hammer sits lonely in the corner.😂
Oh no, lonely slide hammer sitting in the corner.. LOL
Been doing it that way for years on cars at work. Thanks for checking out the video!
Appreciate you dropping a comment!
@tamaracktr6411 . . . You're famous world wide Big Dave! Bit of an aaaaangle! - LOL
@@quaddingsous hahaha yup 👍
I was waiting for a finger pinch with the boot pliers lol. Ask me how I know 😂can’t wait for the ride trip video hopefully the boys are back!
Hey Shawn, Haha Yup have to be careful with the pliers be pinching a finger.LOL
Yup I believe the boys are going to make our next ride trip in September.
Thanks for checking out the video, my friend!
Enjoy the repair videos, thanks for sharing! Have a blessed day !
Hey Phillip, thanks for checking out the video, my friend!
I had a popping noise in my left rear axle on my 550 several years ago. I was able to buy a complete axle off eBay for less than $40 with free shipping. It’s still working great.
The price was so good that I bought another axle just to have a spare. I haven’t needed it yet but it’s there if I do need it.
Wow, that’s a good price. Especially if it holds up. Thanks for checking out the video!
Good job KC, been a few years since I’ve has to do a CV boot on anything. Can’t wait to see the next ride. Stay safe my friend.
Hey Steve, thanks buddy Appreciate it. Appreciate you checking out the video.
That was great timing. I have a 2000 400 Big Bear that the rear Boot is bad. Other than it having Drum Brakes don't you thing it's Similar. I only use the 400 around my small Acreage. I really look forward to your Videos. The only thing is I have a Polaris General Deluxe that I ride at the LOOP & LOTO in MO. I've been to Mulberry once in 2021. It was fun, but it's 6 hours from home. The other two are around 3 & I ride with Friends. When I went to Mulberry it was a one time trip. Keep up the great Work.
Hey Gary, glad you like the videos. Appreciate you checking them out!
Nice video! Interesting to see the inner workings of a cv axle. I've had a couple torn boots on the suburban but i just replaced the whole axle. Have fun on the next ride! We'll be wishing we were there but we'll have fun in Colorado too😎
Hey mornin Rod, yeah, lotta folks just replace the whole axle when they have a torn boot.
You guys have fun at Colorado and be safe.
Are you going to do any filming? Maybe post some videos from that trip?
I'm planning on taking the camera but my mic setup isn't set up right so not sure how good of video I'll get. Last time we were at mulberry in April I got just a bit of video before my camera mount broke and the audio didn't sound good so I've got some changes to do. But all my extra time has went to building my shop so haven't had a chance to mess with it yet.
I liked your video for sure, and you seem very capable and knowledgable. I would appreciate in future videos if you would let us know socket sizes as your removing everything
Hi Jeff, I will keep that in mind and try to remember to do that on future videos.
Thanks for checking out this video. Much appreciated!
Nicely done laddy! Nicely done! (that's what our soccer coach used to yell at us when we were kids - lol)
1:07 - HAHAHAHA!!! Too funny!
Hahahahaha! She’s bit of an aaaangel haha right on buddy thanks for checking out the video!
@@kcatv9556 . . . I passed on your video to the originator of that saying, "Bit of an aaaaangle", Big Dave from TamarackTR and told him he was famous - lol. I see he left you a comment. Nice!
Nice video! I am just now getting around to it because somehow I never got a notification. I was browsing my subscription and noticed it this way. Anyways, you made this look really easy to take off and install. I like the homemade tool for the job. Probably cheaper to make it than going to other route.
Hey buddy, yeah, that happens to me too. Don’t get my notifications.
Hopefully that video will help some folks out if they ever have to do a boot on there Grizzley. Thanks for checking out the video my friend.
Have you guys posted the episode with the Dirt Obession guests yet? I don't want to miss that one.
Hi Bruce, we did not do a ride with the Dirt ObseXXion boys.
Thanks for checking out this video. Much appreciated!
Good video !! U really know what your doing !! Thumbs up 👍🏻 my friend!
Thanks Robert!, Appreciate you checking out the video and for the thumbs up 👍
You are very professional. Congratulations 👏🏻👏🏻👏🏻
Thank you appreciate you checking out the video!
Saubere Arbeit super erklärtes video.
Thanks for watching!
Great tip weld nuts together 👍
Hey Norm, yeah buddy thanks for checking out the video, my friend!
Great information
Hi John, thanks for checking out the video!
Nice job...
Thanks!
Nice help how to change it.
Hey buddy, you’re welcome. Thanks for checking out the video.
I end up just breaking the axle in two😂. Boot would be much cheaper but same amount of work.
Haha yup I guess that would make it easier to get a part LOL!
Thanks for watching and dropping a comment
PLEASE SOMEONE KNOW THE MEASUREMENTS OF THE DUST GUARDS OF THE YAMAHA GRIZZLY 700 2016
I don’t know what a dust guard is on a grizzly. Not sure what you’re asking? Thanks for checking out the video.
What pliers are those!? Can you send me the link sir?
Hey Nathan, they are standard automotive CV boot clamp cramping pliers. I believe I picked him up at O’Reillys auto parts many years ago.
Hope that helps you out, thanks for checking out the video.
@@kcatv9556 thank you! I found them! Very good video 👍🏻