Car trunk led strip install
Vložit
- čas přidán 24. 02. 2018
- Green wire turning signal & hazard lights for both sides
Green/yellow brake lights
Green/white wire-running lights
Black-ground
If you do get the same kit, your yellow wires goes to both turning signals the yellow wires tell you the wire for right tail light & for left tail light. You do need to run a wire across the trunk to other tail light, on my Altima the wires for turning & hazard lights are the same colors for both tail lights (green) you will need to figure it out for your car with a test light. For brake light the kit has a white wire, that will go to green/yellow on the Altima. For your power (red) & (green) wire on the kit you will join those together and tap it green/white running lights on the Altima. As for the black wire on kit goes to ground.
Led strip link; www.amazon.com... - Auta a dopravní prostředky
Fantastic job !
A night test would be great to see how it looks in the dark roads...
Hi i have same one but i don't know what is ACC and VCC and also what is the width lamp, and how do i connect the positive to positive i mean how do i know the the right turn positive and left if u could help me ASAP please
Hello my friend, the LED strip is long, can I cut it?
How you doing Taco? My buddy and I tried to hook up the 3rd brake light, that goes to the top of the rear window. We connected the red positive, and ground (black) and we got nothing? No brake light, right from the start. We turned the headlights on, everything. He connected the green wire, which is the sequential wire, which is illegal. Once you hook the positive, and ground, I should get the full break light, correct?? We didn’t
بس عندي ملاحظه لمن اوصل حق الاشاره لليمن او لليسار واشغل الاشاره يشتغل مع الاشاره ويظفي معي الاشاره مايجلس يمشي خطوط واصل طول ما الاشاره شغال ايش المشكلة
What's (width lamp v+) for ???
Width of lamp
in hhr which i have stop light and turn signal is in the same bulb, how i do this??
Did you figure out how to do it? I have the same problem when I press the brake the hazards flash on the bar
So, the wire that you got across was only connected to the right turn signal? Or did you have more wires?
angello gazani yes you tap that to the box and to the right turning signal
Just got mine how to wire it I got a civic si , can u tell me which wire goes too and what gauge of wire need to extend and where is the negative n positive for power thank you
Arnel N I wouldn’t know what wires your car has bro grab a test light and you’ll find out quick as for the wire I went to Walt mart to grab the wire, it’s like and 18 gauge I believe you can pick up a cheap test light at Walt mart also for like $3 bucks
Where did you get that white box you plugged all the wires into
Derek Jeong that’s the plug for tail light bro
Can i get an tail light plug?
ThenQ very much bro!
Рустам Рустам no problem man
So the positive wire goes to positive to the brake light socket and black wire to chassis for ground
hector nunez yes!
@@yungmexican32 thank u for message I'm waiting for mines to come in they look good
@@yungmexican32 stay safe out there with coronavirus stuff we goin threw God bless
For sure man! If you need help let me know! And thanks man stay safe as well god bless bro!
I hooked my positive, and negative (ground) to start off, to see if I’d get a brake light, on the 3rd brake light, for the back window, and got nothing? Any suggestions would be appreciated? I think I got a bad light?
I wish you would show how you actually put the cords into the car headlights, that’s what I need to figure out
Ben Balman tail light?
yungmexican32 yeah I meant that
Awesome, thanks
Kong Viet thanks!
Taco, is there a difference, if you start at the right side tail light, or the left? Or it doesn’t matter? I bought the LED 144 for my back window, and I wanna make sure I start, on the proper side? Plus the green wire was a flashing mode like police lights, and is illegal?
You can tap it on left or right doesn’t matter, and honestly it’s better if you can get a red led strip instead of the led white you might get pulled over with the white one
@@yungmexican32 thanks, yeah, I just got the all red one today. I couldn’t for the life of me, figure out, how to get the blinkers, and hazards? I just had a couple connections wrong? FINALLY, I have a working light! The last one I bought, I had to send back. Had a bad connection where it snaps together? I have a slight flicker, on the passenger side, but I think it’s my connection? I’m done for tonight. Thanks for the advice 👍
@@markochman75 for sure man, those test lights also work great should pick one of those if you don’t have one and you can test everything out and make sure you’re tapping everything correctly.
@@yungmexican32 I can’t figure this out Taco? I connected the red wire to the brake light, next blinkers, black (negative) I sanded a spot off the paint, so I get a good ground? I’ll get the brake light, then the blinkers won’t work, or flashers? What the hell am I doing wrong? White is brake light, red is power, both yellow are turn signals, I hook it up, and one or another, doesn’t work? I don’t get it? I’m using the same exact test light as you.
@@yungmexican32 solid light is brake light, right? Put your blinker on, and the test light blinks, that’s your signals, black is ground. I connect all that, and get one or the other? I’m missing something?
does this product only work with car lights on? or does it work during the day?
Tuga em Bristol it's basically to have it on at night
Tuga em Bristol it can be on during the day but you have to have your tail lights on
ممتاز جميل
Is it the same for the golf mark 4?
giorgio feraru same procedure, just different wiring grab yourself a test light
Don't know what state you live in, but if you live in Texas you can get fined for having the white (running) light on, might be the same for others.
C.M i did end up getting a fixing ticket but I did not fix it just got rid of the car
I have white light underglow for years and lives in Texas my whole life and never once got ticket
What about back gear light?
Sourav Roy the backup light? That one doesn’t work with the led strip just turning signals brake and hazard lights
@@yungmexican32 yesterday i tried to install i connected all wires as it need (turn signals+brake+backgear light+width light). The problem is when i put the car to back gear its starts flashing red light. (I checked three times all the wires) Why the white light didnt turning on? Is there any solution for this?
You didn’t tap it to the reverse light did you?
@@yungmexican32 i did connected them all right. Its happens only when i switch to reverse gear, 3 times flashing red light. So its related with brake wire and reverse wire, i think i have to do not use one of this wire.
Maybe the problem is inside the strip led?
LED Trunk Flow Light [Need Help]
I have an LED Trunk Flow Light intended for signaling/braking.
It should be very easy to install...
I have a 2013 Mazda 3 I-SV
Just messing around to see how this works I hooked them up to a 9v Battery, they work, so in short, its not a dud…
Now to test them out, I connected the Red (+)Power to the + side of the 9v, then I connected the Black(-)Ground wire to the - side of the 9v… its getting power!
I now connect the Yellow(+)Left Turn Signal Wire to the Gray(+) Left Turn Signal wire in my car, nothing happens…. Their is two wires that connect to my Left Turn Signal, the Gray is Definitely (+)
because when I test this by placing the RED(+)Power, with the Yellow(+)Left Turn Signal Wire and attach them both to the Gray(+) Left Turn Signal wire in my car, all the lights begin to flash.
Anyone know what the hell is going on?
#help #howto #electronics #LED #mazda #mazda3 #car #vehicle
Sean Amor get a test light?