This works! Thank you very much. 2000 chev. In a town of 20,000 resisters can not be bought here, bought an ohm meter I didn't need. Waisted three days researching and trying things. This got me going. Fallow the procese carefully all the way through.
This procedure worked for my 1998 GMC Jimmy that had tge ignitiin tumbler and housing mangled during an attempted theft. A resistor in a detacable 2 position connector across orange and yellow wires now becomes the key after the learning procedure described in this video. THANK YOU VERY MUCH!
Hey Amigo I just did it on a 1998 Chevy 3500. I bought it at an auction like 4 months ago and I couldn't drive it. You gave very good instructions. The truck had the same wires. Thanks to you a lot of people saved money, no stress. Have a Great 2022 God Bless You.
Very helpfull and easy to understand. Trying it on a 2001 s10 blazer. Waiting on security light to go off for the 2nd time. The first time the light stayed on for about 30secinds. Coming up on the 11 minute mark shortly. Hopefully it works. Let you know in a little while.
I followed this video and it worked! I performed this work-around on a 2001 Chevy S10 pickup with a 2.2L engine. The original key was lost, so a new cylinder lock and key was installed. During my experience, for the first two key on/off intervals I would see the security light blinking then go out after about 8 minutes. On the third key on/off interval, the security light stayed solid the whole time, even after leaving it in on position for 20 minutes thinking it would eventually go out, but it did not. However, I followed the video and did the fourth step with the key on/off for 30 seconds only and IT WORKED! IT WORKED! (Security light stays on when truck is running now, same as the video.) I am so happy and my friend couldn't be more thankful and relieved. What made the experience truly awesome was that this fix was done on my friends property that is miles and miles away from any Chevy dealer. Renting a tow truck to tow it out and pay a dealership to fix it was out of the question, but I was able to get it running after years and years of the truck sitting. This video staved a lot of time, a lot of frustration, and easily saved over $1000. Thank you! I hope my experience helps anyone else reading this.
i have a 2000 bagged s10 and the same thing happonned in the same spot but took out half the loom I rewired it all and the pass lock was so bad I tried this and it worked beautifly thanks again
It will work on a 98 This worked on my 98 S10 right at 10 mins it stopped blinking did this 3 times and let it set about 5 seconds and the 4th turn of the key it started and so far so good. Easy to follow video thanks for sharing sir
I had to wait 20 min before the light turned off, for the first time, but it does work. Had to do this trick on my 99 chevy 2 wheel drive truck, starts like a champ every time. Thanks A Lot!!!
I tried this (AND IT WORKED) on my 1999 Chevy blazer. I had to do the reLearn process a few times (the whole day) because the blinking light took way longer than 11mins. Thank you SO MUCH.🏅
I used a 1000 ohm resistor between the cut yellow wire and the orange/black wire. I have a 2000 Sonoma and I changed the steering column for the tilt and cruise control upgrade. After the installation, it would only run 2 seconds and shut off. I first tried cutting the yellow wire and connecting it directly to the Orange/Black wire. That method worked after going through the “10 minute switch on” reset procedure but my security light stays on all the time. I added the 1000 ohm resister between the cut yellow wire and the Orange/Black wire. Now the engine starts and the security light goes out. I hope this is some help for you tubers.
I had this problem then someone tried drilling my truck. on top of the ignition where the wires clip in is completely busted away. I'm having a hard time fining this part. is it a ignition cylinder housing? and how do I replace it? everywhere I try to look it just comes up with the ignition cyilinder
Where do the small green and brown wires connect? I had a "friend" take my lock cylinder out he didn't do a good he ripped all the ignition wires out and pretty much tore up my ignition so I don't know where those two wires go
thanks made did it today.....it worked perfectly had to get a jump off because of battery drain but it's all good now ......preciate the video will subscribe. ...by the way this work on my 2000 chevy astro van....great video man I'm ecstatic.
Last night my security light popped on for a few moments, but then went off again. Now today it's acting like you described, however my security light doesn't come on or blink when trying to start or even with the key in the on position. Any ideas?
Man I've been trying everything on my 2000 s10 I replaced so many part and nothing I just so happen to come across this video tonight and decided why not it can't hurt. To my surprise it worked my trucked fired right up I don't know if the creator of this video will see this but if so a million thanks man your a life saver
@charliearchuleta6044 same thing happened to me and my blazer, I'm going to try the resistor, I bought a used blazer and it already had this done to it, and it still won't start, I'm so confused with these stupid passlock bullshit in these chevys, I've never had any electric problem with a Ford vehicle chevy sucks if you ask me!
thanks man fixed my 01 blazer i had to bust my ignition cause i thought i lost my key and then security light came on so end result 58$ new ignition and did the bypass and bam runs again
I assume the passlock was triggered when I replaced my fuel pump. the new pump won't run now but is getting proper voltage. Should this fix disable the passlock and allow the fuel pump to run again?
It worked on my 2000 blazer. For some reason it took five times to clear the computer. Instead of soldering the wires I used a male and female coupler. Thank you
I've been tryin everything for the last week I watched this video and just did a quick connecter on the 2 wires and tried all the resetting but secur light never wud stop blinking so it didn't work..come to find out the quick connecter didn't splice into it like I thought so I did like u did and redone the 30 minute process and it fired right up and
Thanks you very much I did exactly how you explained and sure enough it started right up preciate it u can't get better than that about the security light I did the same thumbs-up.
Thanks for the video. I have a 1999 Gmc Yukon. Same problem, crank no start. After testing the fuel pump and it's components I ruled out that. I had no fuel pressure. So I followed your advice and solved the problem. Now my truck is running again. Thanks again.
I replaced the blinker switch. My security light is on not blinking and wont crank. Did what you did but my light never goes off learning the new pass code
Worked great thanks. Did this after my bypass module wouldn't work. I don't know why you wouldn't get a 5 cent resistor though, so the security light isn't on all the time afterwards.
thanks for the help I have one question though when the yellow wire is cut do you attach the yellow wire from the ignition switch to the red wire or the other side of the yellow wire that is coming from the harness to the red and wire?
The security on my 99 S-10 Xtreme pickup has been "acting" up these last few months & I was able to quick fix it with other methods that only worked for a few days to a couple of weeks but the other day after leaving work it did it again & I tried this method & THANK YOU man it worked but I want to add the resistor & get the security light off so I have a couple of questions-First when switching my meter to ohms do I touch both probes to the bare yellow/orange black wire connection to get the right resistor value & second do I have to do the relearn procedure after installing the resistor-I will probably solder the resistor in & cover it all in heat shrink.
I have one CHevrolet Blazer 4.3L year 2001. I have try with resistor and without resistor but security ligjt keeps on all the time , and the car start only 1-2 second and turn off . I have try with resitor 5k-18k and same problem. When i measure with multimeter and ignition on , yellow com from ignition and orange/black wire it give 7Mohm-11Mohm. I have bought finally 2 remotes new from china and one original from ebay used and i can not reprogram with computeres or manual procedure (. CAn any help me ?
Hi, I appreciate the video. One question, if I choose to use the resistor and then do the relearn will the security light then go out like it normally would? Again thanks for the video it was a good one.
i am wondering if anyone knows what plug and pins at the computer is the vats? i put a diff engine and trans but the truck i took them out of has vats on the computer and truck they are going into dont have vats. I have a resistor to put in at the comp just need to know what plug and pins are
I bought a blazer that already had this done and it still won't start, what now? The security light just lights up when.the key is forward, it doesn't flash.
thanks my olds has been sitting for 4 years with brand new tires and fuel pump and intake gasket, bothered me. i had taken it to GM dealer 4 years ago and they said it wasnt the passlock system and they wanted me to trade it in and give me $500. but to good of a car so i towed it when i moved and it sat for a year. So GM was wrong this should of been a recall !!!! i needed the car real bad at that time so i bought one from enterprise anyway thanks
Will this work for my 2000 gmc Yukon because I've been having problems for 2 months had a guy come out and put the machine on it and couldn't get pass security
It worked on a 2000 chevy s10. Thanks for the info. But now I have lots of other sensors on. Such as no fuel and ABS and battery light. Any clue for those?😂 thanks for any help.
This is awesome bro, I've got a 99 LS S 10 EXT CAB , 4.3 VORTEC. I. REPLACING ALOT OF THE CONNECTERS ALONG WITH THE SENSORS. I WAS WORNED ABOUT THIS ECU ISSUE HAPPENING. THANKS AGAIN
have a 2000 s-10 runs about a second or two then shuts off. repalced fuel pump and filter. and coils all sensors replaced computer replaced . snapon scan tool no codes goning to try this tonight bypass thanks alot wish i seen this earlier no security light on tho ??
Good video. I have had used a similar method a total of 3 times now on a 2000 Blazer. I was told it has something to do with how I lock & unlock the vehicle. I did not put in a diode or reroute any wires, but since the last time I had to reset it the service stays lit. Not sure why it worked the first 2 times.
@@banshee420100 Thank you. If you have any questions on any of my videos let me know. I am always looking for a good idea for a video so if you have any suggestions I may be able to use it. I have many projects to complete & even start, unfortunately I do not have the time to video all of them. Manuel your support is much appreciated, if you haven't subscribed yet hit that Joe Z button & be sure to comment. This may not seem to be much but it is a big help and much appreciated. Stay safe, Joe Z
Well I'll be damned. This worked on my 99 Suburban. Still have that stupid security light on the dash though. Is this just a temporary fix or can I drive it on down the road indefinitely? Thanks for the video.
I tried this and I tried three different resistors, I even tried replacing the main computer because the original was fried, I even did the relearn procedure and still, MY BLAZER WILL NOT START!!!!! I don't want to have to replace the ignition and BCM. The ignition has already been replaced, I'm so confused and irritated!!!! I've replaced every single part on the blazer, fuel pump, coil, wire plugs, new distributor, new cam and crank sensor, new everything!!!! Still no start, I've even checked all fuses and relays, if a mechanic shop can fiix it, then I do t k kbow what to do.
Tried this, still don't start. Replaced about everything you can think of in my Blazer. Still won't start. Some days it starts, some days it don't. It's got a mind of it's own and runs when it wants to. Any suggestions?
Derek Fielder Might be engine coolant temp sensor also. if your engine light is on you can take it to a local auto zone and they will read your fault codes for free and if it is that... I have watched 100 videos on crank no start condition and one video mentioned ect sensor and only one and it was the reason the car wouldn't start
Buenas tardes . Y que pasa si ise el procedimiento y después de los 11 minutos giro la llave en modo apagado y queda parpadeando el testigo de seguridad sin llave ,todo el tiempo
I turn the key to the on position, the light stays on, doesn't flash. the light will stay on for the whole 11 minutes (I set a timer) and doesn't shut off. I've gotta be doing something wrong.
I've tried this several times, each time I got to the point of starting my car, the battery was dead. I bought a new battery, tried it, the security light never shut off. So, I'm guessing it was already done. I just needed a battery with enough power to start it. I was just out driving it. And I'm not super worried about the light. Thank you SO much for this amazing tutorial.
I have the same problem with chevy blazer s10 . I try all procedures but the security light keep on , not flashing and do not turned off. When i try to start car engine start one sec or 2 and tuned off , security light start blinking. Which maybe the problem?
It worked perfectly , but gives a little fault to solve removing the air intake sensor , good contribution friend . my truck is chevy c -1500 98 Vortec
Thanks so much i watch and other video but you explain better then that other one thanks i fix my problem i have for 6 months ago now i can used my s10 again
This works! Thank you very much. 2000 chev. In a town of 20,000 resisters can not be bought here, bought an ohm meter I didn't need. Waisted three days researching and trying things. This got me going. Fallow the procese carefully all the way through.
This procedure worked for my 1998 GMC Jimmy that had tge ignitiin tumbler and housing mangled during an attempted theft. A resistor in a detacable 2 position connector across orange and yellow wires now becomes the key after the learning procedure described in this video.
THANK YOU VERY MUCH!
my s10 broke down last night and I watched this video today and did this and low and behold the thing fired right up. thanks a million
Been driving me nuts,I was Leary of doing this,but did it and it worked ,thank you very much.
Hey man great fix fixed my 98 s10 after having to take out lock cylinder with key thanks millions saved me a ton
The third video with the same procedure!!! You guys rock!!! I appreciate Y'all sharing this!!!
882
Hey Amigo I just did it on a 1998 Chevy 3500. I bought it at an auction like 4 months ago and I couldn't drive it. You gave very good instructions. The truck had the same wires. Thanks to you a lot of people saved money, no stress. Have a Great 2022 God Bless You.
I forgot to add that I disconnected waited a few minutes and it worked no need to relearn the computer
@johnlittle1939 what did u disconnect the battery r the module
thank you posse rush pass lock fix. worked on my 1998 Silverado .I didn't use tape fix I put a pic of my son thanks again ,darrell beard
Thank you so much this video help me a lot , a was frustrated , but now my 98 Sonoma is working again , God bless you
my 99 blazer is doing the same, doing this this weekend, thanks man. love the black tape fix btw!
Very helpfull and easy to understand. Trying it on a 2001 s10 blazer. Waiting on security light to go off for the 2nd time. The first time the light stayed on for about 30secinds. Coming up on the 11 minute mark shortly. Hopefully it works. Let you know in a little while.
Worked on my 1998 Isuzu Hombre - Japanese Chevy - Wire colors were the same and this all worked perfectly. Thanks
Excellent....started right up...thx....1998 GMC Suburban
Thank you help tremendously. I just used an electrical splice connector for automotive. Thank you again.
99 S10 4 cylinder
Mine started after 2 intervals life saver thank you
I followed this video and it worked! I performed this work-around on a 2001 Chevy S10 pickup with a 2.2L engine. The original key was lost, so a new cylinder lock and key was installed.
During my experience, for the first two key on/off intervals I would see the security light blinking then go out after about 8 minutes.
On the third key on/off interval, the security light stayed solid the whole time, even after leaving it in on position for 20 minutes thinking it would eventually go out, but it did not.
However, I followed the video and did the fourth step with the key on/off for 30 seconds only and IT WORKED! IT WORKED! (Security light stays on when truck is running now, same as the video.)
I am so happy and my friend couldn't be more thankful and relieved.
What made the experience truly awesome was that this fix was done on my friends property that is miles and miles away from any Chevy dealer. Renting a tow truck to tow it out and pay a dealership to fix it was out of the question, but I was able to get it running after years and years of the truck sitting. This video staved a lot of time, a lot of frustration, and easily saved over $1000.
Thank you! I hope my experience helps anyone else reading this.
Worked on a 98 s10 manual thank you!
i have a 2000 bagged s10 and the same thing happonned in the same spot but took out half the loom I rewired it all and the pass lock was so bad I tried this and it worked beautifly thanks again
thank you so much! worked like a charm on my p.o.s 99 sonoma
This is a very easy video to follow for me!! Thank you!
It will work on a 98 This worked on my 98 S10 right at 10 mins it stopped blinking did this 3 times and let it set about 5 seconds and the 4th turn of the key it started and so far so good. Easy to follow video thanks for sharing sir
thanks a lot man it worked on my 2000 chevy blazer. been racking my brain on this thing for a week now. thanks again
Awesome!!! I'm going to do this to my Blazer BEFORE it breaks. Many Thanks for making this video...
I had to wait 20 min before the light turned off, for the first time, but it does work. Had to do this trick on my 99 chevy 2 wheel drive truck, starts like a champ every time. Thanks A Lot!!!
I tried this (AND IT WORKED) on my 1999 Chevy blazer. I had to do the reLearn process a few times (the whole day) because the blinking light took way longer than 11mins. Thank you SO MUCH.🏅
How long did it take? Mine never stops blinking.. :/
I used a 1000 ohm resistor between the cut yellow wire and the orange/black wire.
I have a 2000 Sonoma and I changed the steering column for the tilt and cruise control upgrade. After the installation, it would only run 2 seconds and shut off. I first tried cutting the yellow wire and connecting it directly to the Orange/Black wire. That method worked after going through the “10 minute switch on” reset procedure but my security light stays on all the time. I added the 1000 ohm resister between the cut yellow wire and the Orange/Black wire. Now the engine starts and the security light goes out. I hope this is some help for you tubers.
Clinton Hill would a 12vlt peanut bulb do the same as a resister.
Thanks friend for the information. Do you think a 1000ohm resistor works for blazer 99? How many watts is the resistor?
I am using a translator greetings from Venezuela thanks for the help
Thank you so much!!! Mine is a 98 Blazer and worked just fine😃😁
I had this problem then someone tried drilling my truck. on top of the ignition where the wires clip in is completely busted away. I'm having a hard time fining this part. is it a ignition cylinder housing? and how do I replace it? everywhere I try to look it just comes up with the ignition cyilinder
Awesome works for a 98 chef half ton 4.3.
Where do the small green and brown wires connect? I had a "friend" take my lock cylinder out he didn't do a good he ripped all the ignition wires out and pretty much tore up my ignition so I don't know where those two wires go
This trick worked on my 01 gmc sonoma. Thanks!
Thanks for the video it worked like a charm. 💯 saved me a huge headache.
thanks made did it today.....it worked perfectly had to get a jump off because of battery drain but it's all good now ......preciate the video will subscribe. ...by the way this work on my 2000 chevy astro van....great video man I'm ecstatic.
would this work so i can put a remote start keyless alarm in my 01 blazer
Last night my security light popped on for a few moments, but then went off again. Now today it's acting like you described, however my security light doesn't come on or blink when trying to start or even with the key in the on position. Any ideas?
excellent video,,,,thank you
Good video, great explanation.
Yes! Dah truck starts again! Thanx dude!
Man I've been trying everything on my 2000 s10 I replaced so many part and nothing I just so happen to come across this video tonight and decided why not it can't hurt. To my surprise it worked my trucked fired right up I don't know if the creator of this video will see this but if so a million thanks man your a life saver
Tried ur directions however my security light stayed on and never blinked or shut off..don't know what to do
@charliearchuleta6044 same thing happened to me and my blazer, I'm going to try the resistor, I bought a used blazer and it already had this done to it, and it still won't start, I'm so confused with these stupid passlock bullshit in these chevys, I've never had any electric problem with a Ford vehicle chevy sucks if you ask me!
thank you sir.... I believe I(we) just fix the problem
thanks man fixed my 01 blazer i had to bust my ignition cause i thought i lost my key and then security light came on so end result 58$ new ignition and did the bypass and bam runs again
I assume the passlock was triggered when I replaced my fuel pump. the new pump won't run now but is getting proper voltage. Should this fix disable the passlock and allow the fuel pump to run again?
It worked on my 2000 blazer. For some reason it took five times to clear the computer. Instead of soldering the wires I used a male and female coupler. Thank you
how di you get it to work on your blazer
@@philmanwarren3666 Just followed the video. And shear luck
does 'on' mean only sightly on or does it mean all the way on when all the accessory lights come on
I've been tryin everything for the last week I watched this video and just did a quick connecter on the 2 wires and tried all the resetting but secur light never wud stop blinking so it didn't work..come to find out the quick connecter didn't splice into it like I thought so I did like u did and redone the 30 minute process and it fired right up and
Thanks you very much I did exactly how you explained and sure enough it started right up preciate it u can't get better than that about the security light I did the same thumbs-up.
Did u disconnect the battery before cutting the wires ?? Or should it be done while it's connected? ?
Thanks for the video. I have a 1999 Gmc Yukon. Same problem, crank no start. After testing the fuel pump and it's components I ruled out that. I had no fuel pressure. So I followed your advice and solved the problem. Now my truck is running again. Thanks again.
I have same truck, with the same problems. Is yours still working?
I replaced the blinker switch. My security light is on not blinking and wont crank. Did what you did but my light never goes off learning the new pass code
This worked perfect after all of my other mechanics gave up
Worked great thanks. Did this after my bypass module wouldn't work. I don't know why you wouldn't get a 5 cent resistor though, so the security light isn't on all the time afterwards.
What kind of resisitor did you use?
U r the man great video thank u so much
thanks for the help I have one question though when the yellow wire is cut do you attach the yellow wire from the ignition switch to the red wire or the other side of the yellow wire that is coming from the harness to the red and wire?
Attach the yellow from the module to the black orange wire !! not the yellow half from the ignition !!! just tape that part up
The security on my 99 S-10 Xtreme pickup has been "acting" up these last few months & I was able to quick fix it with other methods that only worked for a few days to a couple of weeks but the other day after leaving work it did it again & I tried this method & THANK YOU man it worked but I want to add the resistor & get the security light off so I have a couple of questions-First when switching my meter to ohms do I touch both probes to the bare yellow/orange black wire connection to get the right resistor value & second do I have to do the relearn procedure after installing the resistor-I will probably solder the resistor in & cover it all in heat shrink.
I have one CHevrolet Blazer 4.3L year 2001. I have try with resistor and without resistor but security ligjt keeps on all the time , and the car start only 1-2 second and turn off . I have try with resitor 5k-18k and same problem. When i measure with multimeter and ignition on , yellow com from ignition and orange/black wire it give 7Mohm-11Mohm. I have bought finally 2 remotes new from china and one original from ebay used and i can not reprogram with computeres or manual procedure (. CAn any help me ?
Hey buddy i just wanna tell you thanks for this video mine work at the first try thanks again
Tried this on my 1999 s10 blazer the security light no longer blinks but the vehicle still will not start. Did I miss something or do something wrong?
Hi, I appreciate the video. One question, if I choose to use the resistor and then do the relearn will the security light then go out like it normally would? Again thanks for the video it was a good one.
it worked! thank you sir
Worked like a charm thank you for sharing this ,saved me the price of a fuel pump..
this will work with a remote star system ?
i am wondering if anyone knows what plug and pins at the computer is the vats? i put a diff engine and trans but the truck i took them out of has vats on the computer and truck they are going into dont have vats. I have a resistor to put in at the comp just need to know what plug and pins are
99 chevy 3500
I have a 2000 S-10 Xtreme 2.2L I4. Can you tell what system in my truck ??
I'm wired up and doing the key on off thing now! Hope it works ! If not I'll post if it does work I ain't turning back!
Thanks Dr. Phil.
I bought a blazer that already had this done and it still won't start, what now? The security light just lights up when.the key is forward, it doesn't flash.
I’m having this issue and I’m going to try it but will the security system key fobs still work?
thanks my olds has been sitting for 4 years with brand new tires and fuel pump and intake gasket, bothered me. i had taken it to GM dealer 4 years ago and they said it wasnt the passlock system and they wanted me to trade it in and give me $500. but to good of a car so i towed it when i moved and it sat for a year. So GM was wrong this should of been a recall !!!! i needed the car real bad at that time so i bought one from enterprise anyway thanks
Will this work for my 2000 gmc Yukon because I've been having problems for 2 months had a guy come out and put the machine on it and couldn't get pass security
Thank you very much this worked on my 2001
What does it mean if your security light doesn't stop blinking after the 11 minutes
moneypitt98
thanks worked on my 98 Silverado. put sons pic over security light lot less work
your video at the end had me laughing so hard to tears
Good video for type 11. If you Chang battery's do you have to relearn again
mi blazer del 99 no enciende le cambie la bomba y no prende y marca security en el tablero no levanta el reloj de la bencina que puedo hacer
It worked on a 2000 chevy s10. Thanks for the info. But now I have lots of other sensors on. Such as no fuel and ABS and battery light. Any clue for those?😂 thanks for any help.
Gracias amigo! Worked like a charm for a customer stuck 50 miles from home!! Appreciate it brother. P.S. was a 1999 chevy s10 pick up.
This is awesome bro, I've got a 99 LS S 10 EXT CAB , 4.3 VORTEC. I. REPLACING ALOT OF THE CONNECTERS ALONG WITH THE SENSORS. I WAS WORNED ABOUT THIS ECU ISSUE HAPPENING. THANKS AGAIN
It works on my 2000 k3500 thanks. But wood like to know how long have you heard about it working for
Does the 99 have chip in key?My 98 Silverado does not have a chip.If 99 does not then i can fix mine like this...
have a 2000 s-10 runs about a second or two then shuts off. repalced fuel pump and filter. and coils all sensors replaced computer replaced . snapon scan tool no codes goning to try this tonight bypass thanks alot wish i seen this earlier no security light on tho ??
What do if it doesn’t flash and it doesn’t turn off
SALUDOS desde Venezuela se puede hacer ese empalme como lo muestra el vídeo y prende el vehículo gracias
oh ya my system has another type of secuirty system in it also a plug in chip under the dash and it didnt hurt it
Good video. I have had used a similar method a total of 3 times now on a 2000 Blazer. I was told it has something to do with how I lock & unlock the vehicle. I did not put in a diode or reroute any wires, but since the last time I had to reset it the service stays lit. Not sure why it worked the first 2 times.
Hi Joe love your videos
@@banshee420100 Thank you. If you have any questions on any of my videos let me know. I am always looking for a good idea for a video so if you have any suggestions I may be able to use it. I have many projects to complete & even start, unfortunately I do not have the time to video all of them. Manuel your support is much appreciated, if you haven't subscribed yet hit that Joe Z button & be sure to comment. This may not seem to be much but it is a big help and much appreciated.
Stay safe, Joe Z
@@JOEZEP54 just subbed and bell you had about 3 videos that helped me in one day now about to see more before sleep good to learn something every day
@@banshee420100 I appreciate your support and am glad you found my channel to be of help.
Stay well, Joe Z
This this screwed up the sequence. How do you start over
Thank you
Well I'll be damned. This worked on my 99 Suburban. Still have that stupid security light on the dash though. Is this just a temporary fix or can I drive it on down the road indefinitely? Thanks for the video.
I tried this and I tried three different resistors, I even tried replacing the main computer because the original was fried, I even did the relearn procedure and still, MY BLAZER WILL NOT START!!!!! I don't want to have to replace the ignition and BCM. The ignition has already been replaced, I'm so confused and irritated!!!! I've replaced every single part on the blazer, fuel pump, coil, wire plugs, new distributor, new cam and crank sensor, new everything!!!! Still no start, I've even checked all fuses and relays, if a mechanic shop can fiix it, then I do t k kbow what to do.
Tried this, still don't start. Replaced about everything you can think of in my Blazer. Still won't start. Some days it starts, some days it don't. It's got a mind of it's own and runs when it wants to. Any suggestions?
Derek Fielder
Derek Fielder Might be engine coolant temp sensor also. if your engine light is on you can take it to a local auto zone and they will read your fault codes for free and if it is that... I have watched 100 videos on crank no start condition and one video mentioned ect sensor and only one and it was the reason the car wouldn't start
Buenas tardes .
Y que pasa si ise el procedimiento y después de los 11 minutos giro la llave en modo apagado y queda parpadeando el testigo de seguridad sin llave ,todo el tiempo
It works for a 98 Chevy s10 also
Gracias
Your video totally works thanks alot.
I turn the key to the on position, the light stays on, doesn't flash. the light will stay on for the whole 11 minutes (I set a timer) and doesn't shut off. I've gotta be doing something wrong.
I think it was done from previous attempts. Turned my car off, figured, what the hell, I'll try to start it. It started right up.
Yep. Driving it as we speak. Runs and drives like it did before this happened, with the exception of the security light being on.
I've tried this several times, each time I got to the point of starting my car, the battery was dead. I bought a new battery, tried it, the security light never shut off. So, I'm guessing it was already done. I just needed a battery with enough power to start it. I was just out driving it. And I'm not super worried about the light. Thank you SO much for this amazing tutorial.
I have the same problem with chevy blazer s10 . I try all procedures but the security light keep on , not flashing and do not turned off. When i try to start car engine start one sec or 2 and tuned off , security light start blinking. Which maybe the problem?
thank you so fucking much! worked like a charm on my p.o.s 99 sonoma
It worked perfectly , but gives a little fault to solve removing the air intake sensor , good contribution friend . my truck is chevy c -1500 98 Vortec
no need for tape over light ...just reach under the column and unplug the passlock module .....no more light.
Where is the passlock module located?2005 astro
@@jameswoods1850
Behind the radio close to the passenger side air vent.
Thanks brother 🙏
Thanks so much i watch and other video but you explain better then that other one thanks i fix my problem i have for 6 months ago now i can used my s10 again
Thanks man