Your use of the lathe is impressive. Cutting the internal jetway broach in the insert you made for the pulley was ingenious. Though the camera angle made it look a bit canted
When welding in the lathe, and not having the ground on the part, the current needs to go through the bearings in the headstock. Creating pits in them.
Muy buen trabajo hermano.! Yo tengo que hacer un trabajo similar a ese; lo haré un poco más adelante cuando tenga funcionando mi torno.! Espero que vos y tus seres queridos estén bien; bendiciones y un abrazo a la distancia.!👍
saludos cordiales mi hermano Mesin una pregunta porke no hiciste una sola pieza haber soldado en la base porke hay riesgo de ke se truene o quiebre la soldadura .bendiciones desde Monterrey México 👍
Salam 1 jiwa boss🙏. Mau nanya nih guys. Di tabel mesin L5 ada ukuran ulir 1.25 jenis mm. Kbetulan mesin L5 klo mmbuat ulir hrus di rubah posisi gigi mm dan inchi. Tpi kok waktu aku setting posisi gigi kok gak ktemu ya boss.Pdhal udah sesuai tabel. Tolong bantu guys🙏. Oh iya itu mesin merek apa guys..lincah bget ..mntapppp👍👍
With Your Welding , you Didn't show where your Clamp ! Was Connected ! And Having the Cross Bar ! Still on ! Looked QIUTE Dangerous ! That said , it seemed that it worked out in the End !
I understand that you have to tack weld But, and while I’m not a professional welder I do a bit snd know a bit about welding. Too little heat poor penetration, too much heat can introduce other problems. But on some things I seen you and others weld they do what I call the dirt dobber method of touch and go or touch and back off and while it isn’t or may not be necessary I would cut most if the touch and go weld off but leave enough for alignment and make a seamless circular weld then cut that weld down to the size needed. Just a personal preference of the way I was taught. Like I said I’m not a professional welder and just a wanna be machinist learning a great deal from your videos. Your use of what I call the wiggly wire to center/square something in the lathe versus use of a dial indicator unless accuracy demand closer than your eye snd the wire can get and I’ve already seen you use the wire then put a disk indicator on that same item to see it was dialed in. The only lathe experience I have is watching how others do it and most follow use of a dial indicator and I suspect the accuracy of their eye has not learned to be as accurate as you and the wiggly wire not that the wire is wiggly just a nickname I’ve given the method. Additionally you and others rely heavily on a vernier caliper with marked off scales in lieu of one with a dial or a digital display and if those with indicators, dial or digital aren’t checked or calibrate periodically with a standard the plain vernier caliper may retain as much or mor accuracy depending on the accuracy of the person’s eye and comfort using it. Good work, wish your videos were subtitled in English, my only language if you can call my written skills in English a skill.
L352 cantik kawan cara menbuat inside square thread
Terimakasih saudaraku ♥️
i like the way how you give a part a second live in stead of making a totaly new one ...
Nyimak.
Sukses sllu bosku video nya. Sangat inspiratif
Aamiin.. terimakasih bang
Your use of the lathe is impressive. Cutting the internal jetway broach in the insert you made for the pulley was ingenious. Though the camera angle made it look a bit canted
Mantap alatnya komplit dan besar
Sehat dan sukses selalu
Aamiin.. makasih mas
Well done, Mekanik Master Mesin! 👌👍
Thanks sir ♥️
Excellent job, 👍👍👍
When welding in the lathe, and not having the ground on the part, the current needs to go through the bearings in the headstock. Creating pits in them.
Gday, the thread cleaned up like a new one, great repair mate, cheers
MM mencontoh cara saya, tapi dalam mimpi :)
Jioooss maseh 👍
Suwun mas e
Hello Yanto,
a top job again. 👌
Best regards, Frank 🙋♂️🇩🇪
Thanks Frank. 🙏♥️♥️♥️
Cepet bgt mas klo ngedrat
sehat selalu mase...Jos pokoke
Cantik sekali bro,
Лайк. Думаю старая гайка была из чугуна. Я бы поступил обратно. Дорезал бы гайку и под неё новый винт.
Mantap bang mekanik mesin👍👍
Mantap
Seems kind of risky running the ground thru the headstock bearings. Just saying.
Request Cara Buat Ulir Dua Arah/Ulir Bolak Balik .Plus Nut Nya Mass.😁🙏 Salam Satu Profesi dari Jawa Timur.
Ide bagus bang.. ♥️♥️
Muy buen trabajo hermano.!
Yo tengo que hacer un trabajo similar a ese; lo haré un poco más adelante cuando tenga funcionando mi torno.!
Espero que vos y tus seres queridos estén bien; bendiciones y un abrazo a la distancia.!👍
Gracias hermano ♥️ 🙏
good job mekanik mesin
Thanks sir
Good job brother....
Thanks sir
saludos cordiales mi hermano Mesin una pregunta porke no hiciste una sola pieza haber soldado en la base porke hay riesgo de ke se truene o quiebre la soldadura .bendiciones desde Monterrey México 👍
Bageimana caranya membuat Drat persegi panjang 6000 Mm ( 6 meter )
muy buen trabajo maestro 👍
Thanks sir ♥️🙏
Salam 1 jiwa boss🙏.
Mau nanya nih guys.
Di tabel mesin L5 ada ukuran
ulir 1.25 jenis mm.
Kbetulan mesin L5 klo mmbuat ulir hrus di rubah posisi gigi mm dan inchi.
Tpi kok waktu aku setting posisi gigi kok gak ktemu ya boss.Pdhal udah sesuai tabel.
Tolong bantu guys🙏.
Oh iya itu mesin merek apa guys..lincah bget ..mntapppp👍👍
Хороший результат 👍
Work done 👍
God bless you.👌
Thanks sir
With Your Welding , you Didn't show where your Clamp ! Was Connected ! And Having the Cross Bar ! Still on ! Looked QIUTE Dangerous ! That said , it seemed that it worked out in the End !
I understand that you have to tack weld But, and while I’m not a professional welder I do a bit snd know a bit about welding. Too little heat poor penetration, too much heat can introduce other problems. But on some things I seen you and others weld they do what I call the dirt dobber method of touch and go or touch and back off and while it isn’t or may not be necessary I would cut most if the touch and go weld off but leave enough for alignment and make a seamless circular weld then cut that weld down to the size needed. Just a personal preference of the way I was taught. Like I said I’m not a professional welder and just a wanna be machinist learning a great deal from your videos. Your use of what I call the wiggly wire to center/square something in the lathe versus use of a dial indicator unless accuracy demand closer than your eye snd the wire can get and I’ve already seen you use the wire then put a disk indicator on that same item to see it was dialed in. The only lathe experience I have is watching how others do it and most follow use of a dial indicator and I suspect the accuracy of their eye has not learned to be as accurate as you and the wiggly wire not that the wire is wiggly just a nickname I’ve given the method. Additionally you and others rely heavily on a vernier caliper with marked off scales in lieu of one with a dial or a digital display and if those with indicators, dial or digital aren’t checked or calibrate periodically with a standard the plain vernier caliper may retain as much or mor accuracy depending on the accuracy of the person’s eye and comfort using it. Good work, wish your videos were subtitled in English, my only language if you can call my written skills in English a skill.
عمل ممتاز اخي
🙏♥️
Bom dia muito bom parabéns seu amigo maritaca de Aguai sp Brasil
♥️🙏🤝🇧🇷
Berapa biaya bikin seperti itu panjang 100cm
bang itu maksimal bisa panjang brp membuat mur kaya gitu
Tergantung diameter lubang mas, semakin besar semakin panjang bisa..kau kecil pahat tidak bisa panjang soalnya getar
👍
🙏🙏 👍🏴
♥️🙏🇮🇩🤝
Mas,disitu bisa repair cv joint oblak gak ya?
Oblak dirumah gotri atau di as gearnya bang?
@@Yantoo dirumah gotri nya aus sama di as laker nya itu.bisa direpair gak ya?
Bg kalo mo belajar bisa?🙏🙏
Mau PKL bang?
berapa upah nya mas kalo bikin seperti itu
Pertama dapet apa
Dapat kopi kalau kesini bang.. 😁
good
🎺👍👍👍💥🛠️⚙️⚒️
mas munta kontak WA sy mo pesen sesuatu..tks🙏🏻
O vai apunar logot mok kamot rakhak vai pelish
When I saw the burnt oil, I knew that the movie was coming out of the barbershop
Bisa minta no wa nya mas 🙏