How To Replace Valve Cover Gasket Citroen DS5 1.6 THP 155, (DS3, DS4, Peugeot 3008, 5008, RCZ etc)
Vložit
- čas přidán 25. 07. 2024
- No nonsense guide on replacing the Valve Cover Gasket (VCG) in Prince engines. This one is a Citroen DS5 with the 1.6 THP, EP6. This should be the same on the Citroen DS3, DS4, Peugeot 3008, 5008, RCZ, Mini R55, R56, and BMWs with the N12 and N14 engine.
While the valve cover is off please check all timing components for wear, it is a very common issue in these engines. The timing chain should have zero play or slack in it. It is usually caused by long oil change intervals of more than 10,000km. Please change your oil every 5,000 - 7,500km. Early signs are a rattle sound on cold start. If you catch it early enough you may only need to replace the chain tensioner, if left too long you will need to replace the timing chain itself. Also check for any broken plastic pieces.
Valve Cover Gasket OE Part Numbers:
CITROËN 0249E6
CITROËN 249E6
CITROËN 0249E7
CITROËN 249E7
MINI 11127572851
MINI 11127552074
PEUGEOT 0249E6
PEUGEOT 249E6
PEUGEOT 0249E7
PEUGEOT 249E7 - Auta a dopravní prostředky
Indeed just what I needed, a very good tutorial.
Thanks for uploading.
Thank you so much! Just did this job. Couldn't have done it without your tutorial. 🙏🙏🙏
Great video, I will do this in my car. Thank you very much!🎉
Awesome video! Thanks so much!
Simple and great. Tks
Just what I needed! Thank you!
Great video / tutorial. Very helpful.
Nice Video
i would wish to see this on the thp200 from 2012, want to remove mine but its a bit different to this one, also its hard to get these bolts nearby the airfilter. u also have to remove the heat shield
Well done
Thank you for this very useful instructions. Your instructions also fit to Peugeot 308CC (THP) - as I own. Can you give me some more information about the sealing grease (RTV Silicone) for the corners? Any recommanded products?
super, thank you
Could you please tell how long does it take to replace the valve cover?
I have had my valve gasket changed on my Citroen C5 1.6 THP but can still hear a whistling sound from the engine oil cap... I cannot find a pcv valve diaphragm on my model nor yours.... Can you advise?
I understand that there are several versions of valve covers, the last one I think allows the pcv valves to be changed without changing the cover, some say that gas recirculation works better, what is your opinion about it?
I wouldn't replace the valve cover itself unless it was either leaking or over 200,000kms. If you do want to replace it for either of those reasons I'd personally just refit the variant that came with the car since you'd have to upgrade the turbo intake pipe as well if you changed.
Need to do mine, leaking at the front, by turbo... thank you....
❤❤❤
Hi, thank you for your work. How do you know if you have to change only gaskets or the entire valve cover ?
Examine the valve cover for any signs of damage or wear. Look for cracks, warping, or any other physical damage. If the valve cover is damaged, it will need to be replaced. A cracked valve cover might not seal properly, and this can cause vacuum leaks. These leaks can lead to rough idling or even engine misfires. You can also look at where oil is leaking from, if it's low down it's likely the gasket, if it appears to come from higher up on the valve cover it could be due to a crack.
@@HeroRepairs Thank you for your answer. I have examined the valve cover and I have not identified visible damages but I clearly have vacuum leaks and rough idling. Thank you.
What happens if ive gotten the screws mixed up mate, is there a diagram for what length screws go in which holes? Cheers
At 5:41 in this video I have them laid out in the correct order.
Hi is neccesary te torgue key and the bolt tighten with some order?
At 6:28 I show the correct torque sequence.
I recommend using this sequence, but you would likely be fine using a generic pattern going from inside to outside.
can i apply this on 2014 peugeot 508 1.6 thp as well ?
Yes it should be the same.
hi. what's your opinion for a 408 2012 1.6t with 180k miles, is it necessary to reuse the old original cover or change to a new oem cover? Thanks in advance
I would advise replacing the valve cover
@@HeroRepairs Thanks for the reply! noted. much appreciated
Warum thp 155 ? Icb habd suf meinem thp 150 aicb diesen gleichen ckver
Ciao è vero che questo motore thp dà problemi alla distribuzione , turbina , testata
Sorry but I can't understand the question? Are you asking about common problems with the THP engine?
thnk
laik