P01：Backlight lamp brightness, level 1 is the most dark, level 3 is the brightest; P02：Unit mileage, 0: KM;1: the MILE; P03：Level of voltage: 24 v, 36 v, 48 v, 36 v (by default); P04：Sleep time: 0, means don't sleep;Other Numbers means for the sleep time, range: 1-60;Units of minutes; P05：Assistance gears:0, 3Mode：1lever 2V、2lever 3V、3lever 4V; 1, 5Mode：1lever 2V、2lever 2.5V、3lever 3V、 4lever 3.5V、5lever 4V; P06：Wheel diameter: unit, inch;Accuracy: 0.1; P07：Speed measuring magnetic steel number: range: 1-100; P08：Speed: the range 0 to 50 km/h;The default 50, 50 said not the speed limit; Note：when the speed is greater than the set speed, shut off the PWM output;When speed down to less than the set speed, automatically open the PWM output, driving speed to the current + 1 km/h; Numerical based on km as a benchmark here, after the unit set from miles to miles, display the speed of numerical value is automatically converted to the correct miles, but miles under the interface of the menu in the values of speed limit set by the data conversion, MPH speed limit values are not consistent with the actual display, P09：Zero start, non-zero start setting, 0:0 start;1: the non-zero start; P10：Driving mode setting 0: power drive (decided how much output power by power gear, at this time to turn the invalid). 1: electric (by going to drive, steering gear is invalid at this time). 2: power drive and electrical drive coexist (electric zero start state is invalid). P11：Power sensitivity setting range: 1-24; P12：Assistance start the intensity setting range: 0- 5; P13：Power magnetic steel plate type 5 Sherwin grain of magnetic steel three types; P14：Controller for the current limit value to set,12A(by default) range: 1 - 20 A;
hi , i fallow this video , but the ebike only work if the light is on in the display , and i have no kmh recorded ...it stay at zero ( i have 48v ebike )
Hello, Does anyone else own a Nakto fat tire mountain ebike as well and know an ebike shop in the Philadelphia Pa area willing to repair it? Not sure what my bikes electrical issue is and I've replaced the throttle, rear hub wheel( original damage issue) and contol box in an effort to weed out the issue since a black ice fall in December!
P01：Backlight lamp brightness, level 1 is the most dark, level 3 is
the brightest;
P02：Unit mileage, 0: KM;1: the MILE;
P03：Level of voltage: 24 v, 36 v, 48 v, 36 v (by default);
P04：Sleep time: 0, means don't sleep;Other Numbers means for
the sleep time,
range: 1-60;Units of minutes;
P05：Assistance gears:0, 3Mode：1lever 2V、2lever 3V、3lever 4V;
1, 5Mode：1lever 2V、2lever 2.5V、3lever
3V、
4lever 3.5V、5lever 4V;
P06：Wheel diameter: unit, inch;Accuracy: 0.1;
P07：Speed measuring magnetic steel number: range: 1-100;
P08：Speed: the range 0 to 50 km/h;The default 50, 50 said not the
speed limit;
Note：when the speed is greater than the set speed, shut off the
PWM output;When speed down to less than the set speed,
automatically open the PWM output, driving speed to the
current + 1 km/h;
Numerical based on km as a benchmark here, after the unit set
from miles to miles, display the speed of numerical value is
automatically converted to the correct miles, but miles under
the interface of the menu in the values of speed limit set by the
data conversion, MPH speed limit values are not consistent
with the actual display,
P09：Zero start, non-zero start setting, 0:0 start;1: the non-zero
start; P10：Driving mode setting 0: power drive (decided how much
output power by power gear, at this time to turn the
invalid).
1: electric (by going to drive, steering gear
is invalid at this time).
2: power drive and electrical drive
coexist (electric zero start state is invalid).
P11：Power sensitivity setting range: 1-24;
P12：Assistance start the intensity setting range: 0-
5;
P13：Power magnetic steel plate type 5 Sherwin grain of magnetic
steel three types;
P14：Controller for the current limit value to set,12A(by default)
range: 1 - 20 A;
What is factory reset
If I lower p12 what will happen
Thank you for the information. i was able to readjust my settings. you all are Awesome!!!
where can I found this part for my electric mountain bike this same model
讲得很好👍
Hi how do I order a new LCD screen for my fat tire bike> I've called the number on the website many times and emailed. please help
How do you reset it back to factory settings?
How do you reset it to factory settings please!
I have motor error, how can it be reset or where is the error? Wheel does not turn battery fully
Can you reset a S 861 display controller panel i only get 3 bars of power can't get to speedometer its at 0.4?
Can you show all The factory settings I have a 37 volt 7.8 amp battery and a 250 watt motor
hi , i fallow this video , but the ebike only work if the light is on in the display , and i have no kmh recorded ...it stay at zero ( i have 48v ebike )
Hello, Does anyone else own a Nakto fat tire mountain ebike as well and know an ebike shop in the Philadelphia Pa area willing to repair it? Not sure what my bikes electrical issue is and I've replaced the throttle, rear hub wheel( original damage issue) and contol box in an effort to weed out the issue since a black ice fall in December!
И сте ли от този вид дисплей? Искам да поръчам
Can you are explain all the P numbers
how do you raise the top speed?
Right
how can I find a manual for all the other settings?
Sanjeev Dhanda did you found it?
Sanjeev Dhanda did you find manual i would need it to.thanks
I need a manual too
Search for zp-LCD.pdf
Hey there I need a manual, my screen menu isn't even in the same order.. and only have PO. 1 2 3 4 5 6 7 8 there's no other P1
Why does nakto not put any info in their users manual. How do I turn on the headlight??
@MISSDAYZEEDEE actually I figured it out. Tap the cur button.
@MISSDAYZEEDEE from what I understand it's called a cruiser but on Amazon it's a "26 inch 300w fat tire ebike from Nakto"
They definitely have a lot of info in their manual. Even ones you can download online.
@@Hackerman-bd9hq not true
@@joshuazayas9707 not true
Mine doesn't even turn on properly just have a empty screen with 4 lines like it wants me to put a code or something
esiste un manuale di settaggio in italiano?
No.Japon siempre.
Damn, I need a new LCD controller
I'm in the same boat. I keep getting an E 10 error on mine.
What model lcd is this? Is there a manual i can get? I have 17 settings not 15
Google doesn't bite, this is Focan s861
try this wooshbikes.co.uk/2014/support/zp-LCD.pdf
@@keyproductions100 perfect. thanks for that
Please, how do you reset controller?
How do u reset the 861display
@@bruceypatterson205
I'm trying ta find out myself about the S861 reset only 3 bars of power can't get more speedometer is on 0.4 setting?
На русском есть инструкция?
Р01 настройка яркости
Р02 выбор километры или мили
Р03 вольтаж батареи
Р04 время режима сна
Р06 диаметр колеса
Р08 лимит скорости
Р09 нулевой или ненулевой старт
Р010 настройка зарядки
Р011 чувствительность PAS
P012 начальная интенсивность
Р014 лимит контроллера
Р016 перезагрузка,переустановка
czcams.com/video/cjY-kdzcXbE/video.html
@@user-ly3om3ww2v у меня дисплей имеет всего 8 пунктов в меню. может встречал тоже такой? ищу настройки на него по умолчанию
@@user-ih9oi1vn3b у меня был экобайк. Там тоже 8.
Так и не смог до конца разобраться...
Марк Шерман плохо(
Найти нигде не могу настройки.
Нашел на 8, а они тоже другие)
WTF just want to change to the speed to 28mph.. how does one follow a video like this? 😂
Did u figure out I'm trying to figure out nuts
Unfortunately very strong accent, so very difficult to listen & understand.
Not for public presentation, what have to be clear & good English.
Me know understand either.Vehy hard understand.Must use google translator.If theres a test on this im in trouble.