BRIGGS AND STRATTON LAWN MOWER ENGINE REPAIR : HOW TO DIAGNOSE AND REPAIR A BROKEN FLYWHEEL KEY
Vložit
- čas přidán 8. 08. 2013
- JEREMY FOUNTAIN
THEMOWERMEDIC1
MAIL AND BUSINESS INQUIRES THEMOWERMEDIC1@GMAIL.COM
/ themowermedic1
/ themowermedic1
/ themowermedic1
/ themowermedic1
CHECK OUT TREY DRIVER AND HIS AWESOME CZcams CHANNEL AND DEALERSHIP
TREY DRIVER
BIG BUCK MOWERS AND EQUIPMENT
3301 STATE HIGHWAY 121
BONHAM TEXAS 75418
www.BIGBUCKMOWERS
/ treydriver1
/ bigbuckmowers
/ bigbuckmowers
-~-
JEREMY FOUNTAIN HAS BEEN A PROFESSIONAL SMALL ENGINE TECH FOR THE PAST 25 YEARS, WATCH AS HE SHOWS YOU WHAT A BROKEN FLYWHEEL KEY WILL DO AND HOW TO FIX YOUR LAWN MOWER YOURSELF FOR ABOUT 3 DOLLARS
BRAVO, Jeremy !
I'm also a small engine tech,(22 yrs),and I've watched other videos(some were "pros"),and very few used a puller! Most just "pry & pound",and don't seem to grasp the damage they can do,that way !
From one "old-schooler" to another: WELL DONE !
From one small engine mechanic to another, excellent advice. Please use the required zinc flywheel key. Never use steel for any reason. Guy from my hometown went the cheap way and used a cut horseshoe nail and the flywheel exploded after hitting a tree stump. He lost half of his right leg from it.
8 years later.... Thank you, very much!
Just want to let you know that you are about one of the best teachers I have found on youtube.
Thanks, your video helped me repair my engine. Finally it started easily.
Yes. As stated in the video it is very important to clean the engine and the flywheel prior to re-
installation
Good videos man. I can't believe all the folks asking so many questions.
NO HARM NO FOUL BRA! THANKS FOR WATCHING! CHEERS!
AS I STATED IN THE VIDEO THIS WAS NOT A CRITICAL TAPPING PROCEDURE....IF I WERE INSTALLING A HELI-COIL I DEF WOULD RUN MY TAP BACKWARDS TO CLEAR THE FLUTES THANKS FOR THE COMMENT
I like the way you instruct, you tell what, how and why. I thoroughly your teaching video.
Thank you.
THANK YOU! This worked perfectly and my mower runs again.
Been a machinist for a long time, mills and lathes go through keys like that, I get leeway material by the foot, cut it and use it, think like 2 dollars a foot or so, mill table power feeds always sheer when the table is locked and they hit the rapid feed, thanks for the video
Explained perfectly. Thank you.
Another great video, Jeremy!
I was going to ask where you got that puller ? Seems I am not the only one who wants to know where you get all those wonderful tools. Thank You for making these videos. You have helped me a lot.
For a small engine mechanic that only knows the basic on how to start up and cut the grass this is a great way to learn how to fix the common problems over the motor backfiring through the carburetor and muffler and basic intake if engine repair.
Merry Christmas 20200
I’m bored and looking back to old video
AllWAYS fun to watch them
Thank You’ll
amazing youtube class.........thk jeremy!!
THANKS VM!
If other people feel like they can do better making videos I tell them to get out of it I think you do a very good job and a thorough job making your videos thanks for your hard work and dedication
THANKS SIR!
Great video....very informative...I'm assuming the most common cause for breaking a key is by hitting an object, or do they wear out with time?
Thanks for the info
You could use torque limiting extension to torque down the flywheel using an impact driver.
Thanks for nice vedio. I went know same engine & same model ignition problems
I like that Tach. No wire to wrap I like that. Using that tach and the set up of it would make a interesting video.
the rope trick is fine just make sure the engine is at tdc on the comp stroke so you dont bend a valve
Great job…👍👍
Great video
Great how to man. I've got a push mower with 6.5hp B&S engine. It works great-always starts up on first pull. It does however leak a bit of oil onto the deck. I'm guessing maybe loose bolts or bad seal somewhere. Any advice? Thanks
Hi there i really like your youtube channel.
Nice Video. Can you show for what all the levelers on the carburetor are, and how i adjust them the right way? thx
I have 2 craftsman lawn mower's.they both want start. I changed the spark plugs cleaned the carburetor.do you think it's the spark plug core
I appreciate your work and thanks!
Have a Toro self propel with a Brigs and Stratton engine. Quite suddenly while mowing it started a mettle on mettle rub. Engine itself seems to be running at speed, started with normal effort, not backfiring, etc.
Did not appreciate that blade hit something, and the blade itself is not rubbing. Manually spinning the blade did not feel resistance or a rubbing sound. I went through the process of removing/reattaching blade assembly anyway (rule out the obvious) but no joy or obvious defect. The sound seems to be coming from above the deck not below.
Was wondering if it was the key or flywheel but not your description of backfiring or pull rope resisting, etc.
I cleaned around the engine, confirmed that there is oil, etc. I have just about enough small engine knowledge and enough tools to be dangerous. Any suggestions on what I should be looking for?
Great video Jeremy. My crank on a 3 year old Sears Craftsman gas powered lawnmower with a B&S 190cc engine broke yesterday and the blade flew off taking a chunk out of my mower's deck. Any videos or advice on how to change the crank. Engine and flywheel key still in great shape - mowers still runs great. Event was a little scary.
your right.....the key is just an alignment tool basically.......once you torquge the flywheel down you could actually remove the key and it would stay in place for ever untill the mower hits a pipe, root, rock, ect
Thank you.
hey jeremy i have an old 16 hp horizontal Briggs and stratton the long fuel jet i had accidentally snapped at the lower fuel jet holes. will this jet and carb still function
nice! i have a briggs 11 hp vertical shaft flathead, cant get it to run it has 85lbs compression spark and fuel. its pull start. when i pull it snaps the cord back hard! i checked the flywheel key and even removed the flywheel to be sure it was ok and its is. any ideas? i did also check that both valves are opening and closing tho i did not check the clearance with my feeler gages
Jeremy, I have a 14.5hp Briggs OHV engine. Engine is blowing oil from crankcase to crankcase breather and into the carburetor. What usually causes this? Thanks Mark D.
I would like to know the easiest way to replace the gas line is located directly underneath the flywheel to the carburetor mine is dry rotted and leaking please let me know thank you
I loosen the nut, spray PB Blaster on the shaft where the key is, pry up on the flywheel with a screwdriver and hit the nut with a hammer and that usually pops the flywheel loose.
Nice video. I noticed you didn't clean the crud off the motor that was underneath the flywheel. Is it just not worth the time?
Liked and subbed.
My old flywheel key got sheared and I took off the flywheel and broke it in the process. I ordered another flywheel and key but the flywheel looks different . The new flywheel has something a little extra on the bottom and it may be a tad bit taller in height. The one I originally had looks like the one in this video. I just wanted to know if it really matters?....
Also it still makes the same noise when I try to start it. Like a cling/clanking noise? Help!
Great!
had a sears riding mower with Kohler engine and wouldn't charge. finally after much taking apart and trial and error, pulled the fly wheel off and the magnets had come off of the inside of the flywheel. new $90.00 flywheel and worked fine ever sense..
FYI
Jeremy, where did you buy your wheel puller? I have looked at several outlets but cannot find one specifically like the one used in the video. The puller I have is stout enough but the slots/holes are too wide and do not allow the bolts to align straight into the holes in the flywheel.
Good, easy job! Couple questions: What is correct torque, when you open engine, that block/sump cover, with 6-7? little bolts?? And is valve clearance pretty much same in 3.5/4. and 5 hp B&S engines?? What is it: intake/exhaust?? And one more question: how do you adjust that: grinding valve stem??? Thanks a lot, youtheman =)
Instead of a wheel puller I use an air hammer. I remove the bolt holding the flywheel on. Set aside the washer or the pull start cup or what ever the mower has between the bolt and the flywheel. Then I put the bolt back in and screw it almost all the way down. I have a round tip attachment for the air hammer. I put it against the head of the bolt and pull the trigger. Just a split second and the flywheel pops off. Much much faster than using a puller.
how do you torque specs and rpm specs for these engines? I took a repair course years ago and when I went through the manuals they never gave me specs
Hi Jeremy Was wondering if you have a video that shows how to replace the throttle lever on a Briggs I broke the plastic part that holds the linkage cable
Would be a good ideal to clean off the engine or does it matter before reinstalling the flywheel.
I have a 14.5 Briggs in a white lawn tractor purging gas from muffler! How do I get carb off to replace float and needle??
did you check the blade adapter ? when they kick back,it may have a cracked blade adpater
In my experience, keys fail when someone runs the mower over a large rock/cement - stopping the engine far faster than it should stop.
I don't think it's cheap engineering to use a part that will sacrifice itself to save other parts.
Is it cheap engineering to use fuses in electronics?
I do agree that they should tap those holes though.
Do you have a video on camsaft removal and checking on a 14.5 hp ohv engine. Was trying to adjust valves and the push rod would not push the valve up or down. First symtom was not cranking. Seemed to have too much compression
Good video. Also good idea on video. Let me know if I can be of any help.
Can you provide a link of model info of the puller you used here? Great video.
I have a 15hp briggs and Stratton OHV that back fires and wont start. Do you think its the flywheel key?
Do you go to a lawnmower repair shop to buy the key ?
or did you have use Home Depot/sears/ Loews.....
The temperature is remains increasing, and the termostat or chock need to be replaced?
I was annoyed when I tried to use the puller and found the 2 wheel holes were not threaded!!! I am planning to use a M6 tap to solve this. I hope it works!
I would like to know what the tool you have to see the rpm and where you can get one. I am a landscaper and i also fix small engines. I usually set the rpm by listening to the engine speed.
Where did you get that handy puller and the tach?
I had an engine, Briggs 675 series that had the whole electric start set up deal and when I went to pull the flywheel, I noticed the key was messed up. I got the flywheel of. I just about took that engine apart because when you would try to start it it would blow oil out the carb and pop out the muffler. Sure enough that was the problem. Now I have this Briggs's 675 series motor that had electric start in pieces. Oh well, a spare non electric start engine is going on the mower and now I'm going to just sell the electric start component's.
What is the part number for that flywheel key?
A flywheel key for $1 is a great deal. over here we pay through the roof for any little thing from a mower shop. example.. airfilter for 3.5 briggs $11 . fuel primer bulb and plastic base plate $ 12 , a cirlip for the wheels costs $1 just to name a few . I have not bought a flywheel key , but I would imagine they would be $8 or so . I would be thrilled to get one for $1 . mower shops here charge like a full blown motorcar workshop .
I have a Briggs & Statton lawnmower engine that blows black smoke and carbons up the spark plug, can you advise me
I have a Briggs & Stratton engine that before it quit it was blowing black smoke out of the muffler, can you help me with this, thanks.
What would you do if a 40 turn in on the tractor motor blew up again I work for is to work for said that his throat or motor blew up and it was basically junk is it fixable or what I have to go get a new motor because I just want to find out because I don't want to videos and I can't figure out where when I would have to do
better for the key to fail than the crankshaft.
Good work Jeremy. Your suspicion was right. Now, no more "poo poo."
i see you used channel locks to hold the flywheel. can you instead use the old "rope in the cylinder" trick on a 4-stroke (with valves, vs 2-cycle engine) to keep the piston from moving to make your final torque, or will this potentially damage valves? i'm trying to "properly" torque the PTO clutch bolt onto the crank shaft of horizontal Kohler Command engine on a shaft-drive Cub but the engine wants to rotate, and impact isn't precise.
Totally missed that. My bad man.
If the flywheel key is OK what would be the next issue to look for?
I'm thinkin' this is the problem with my 2006 mtd yard machines lawn tractor I bought on craigs list last week for $200. It cold starts fine but after it warms up when I engage the deck it bogs out and stalls, then backfires through the carb when I try to restart it. I took the carb off and cleaned it with carb cleaner and ran a wire through all the passages but still the same problem. I haven't messed with the rockers or the ignition module yet. You thinkin' what I'm thinkin' too?
Mine didn't have a sheared or even damaged key. Is there a plastic part in the timing on some of the briggs engines?
Sounds sweet as a nut :-)
Seems to be a common problem the key, shame they didnt put two woodruff keys opposite each other to stop this, or just a double thickness key.
Allways enjoy your teachings jeremy :-)
Jeremy, my Briggs and Stratton 210 won't start even though the gas tank is full the line is patent. its almost new but just can't get it to stay running. if I pour a little gas into the carb it will start but then shut down. not sure what to do now.
What do I use to measure my speed( rpm)
Hi me Paul from Germany.
And i hope u can help me on a Springproblem on a used Generator with an 8hp Briggs/Stratton Engine.
I clean him with a Brush and now a little Spring is not on her original Place .
Excuse my english.
Sincerelly Paul.
I totally screwed up. I tapped the flywheel with a 1/4 20, and apparently screwed down too far, because it went all the way through the flywheel on the left side. So now on one side is is okay, but it is busted through from the bolt on the other side. Do I have to buy a new flywheel? Is there anyway I can fix the hole! Thanks!
Maestro a cuanto se calibra las válvulas y la bobina?
What about JB Weld? Would that work?
I have a lawnmower with a Briggs and Stratton overhead valve engine but sometimes the engine will start and most of the time it won't start. I cleaned the carburetor but the groove in the flywheel is slightly off from the groove in the crankshaft. Do you think the flywheel key is broken or cracked?
Brian Mott Street an
I broke one of the wings on my flywheel off. What is that going to do to my mowers performance?
Hi I have a new Briggs 6.75 peak Tq, engine that kick back like a flywheel key. pulled flywheel to check key and there is no key or keyway on this flywheel? what is up?
You seem to have access to great range of parts in the USA here in Australia we never see pre packaged things like fly wheel keys everything has to be bloody ordered .dont you work at Lakeview mowers these days ?
OK!!
What is the model number of that Briggs and Stratton Engine?
whats the name of the tool you used to measured the rpms?
hey bud, in the case that the sheared key is on there good what do you suggest? I got the steering wheel puller on there, holes tapped to 1/4 20 and it pulled the thread out of one of the holes whille trying to remove it.
get a nut on the underside.
would any fly wheel key fit a briggs & Stratton lawn mower? how do I find out which one to buy? thanks
Your model #
Jeremy...I got a Honda HRT 216 S3DA-K2. The Drive belt broke. It is not listed in my shop manuals. My mower tranny is the kind with a "S" shaped rod which sticks vertically out of the tranny box. I am waiting on a 36.3 inch belt, hoping it will be the right one. Grass continues to grow in SC. Any help would be really appre, since all of the parts places around here only want to sell mowers not parts! They wouldn't know a lawn mower if it fell on them!
Do you have a part #
What is the model number on your mower and that puller you used
your RPM checker how much and where did you get it ???
My neighbour has a "Mums: Ja #198544#" lawnmower. I guess it was hardly used coz the bearings, the cylinder and the rings are all OK except the exhaust valve came loose. As it turned out its guide, that looks like an insert, crumbled to several bits.Poor old b...d is very disappointed and I'm trying to help him but no idea. Any suggestion?
check flywheel key 1st then let me know what you find
Hello ! i have / was gifted a troy built 21" 725 ex lawnmower, I detest the new throw away mentality and would like to try to diagnose my issue. could you possible help ? my mower will run , but it runs really roughly. i have checked for spark, it has spark. i have taken the carb off and cleaned that and the tank, it had water in the bottom of the float bowl last time, not sure where that came from. i also cleaned the tank and changed the gas. the lawn mower runs but runs roughly. when i run it without the exhaust , yes its loud as heck but it seems to run better, with no exhaust and or air filter either. i figure next free time i get im going to run a compression test on it (will have to buy that) and maybe a new carb. I just don't want to waste the money on the parts cannon if all else fails and have to buy a new lawn mower after having bought those parts. thanks in advance for the information.
So let my bad experience (below) be a caution to others, if you're going to use a tap, be very careful you don't turn it too far. I thought I was going very slowly and carefully, and I didn't push it too far, but I guess the flywheel is more delicate than I thought!!