Just a note with the GX, you can fill small tanks with it easily enough but you must work in 5 min intervals, bleed valve, then keep fan running for another couple minutes until cool again. Repeat that cycle as-needed but keep special attention to bleeding the line between cycles as this motor can be damaged if started under pressure. I only have a little 45CI HPA tank but the GX works fine taking me back from 3000psi up 4500.
Thank you. Very nice well stated, structured and concise video. I own both also and would not do without either. As will all things, maintenance is part of the pride of ownership. Take care of things and they will usually take care of you.
I own both compressors, Mark and just purchased the new GXCS4 that everyone is raving about. I LOVE my Yong Heng blue box, and I've only used my GX2 twice with zero issues.
its a tough decision on compressors, i have an old shoe box that i still use. It is slow , i have one of the first models out and havent did anything to it but replace O rings. I been looking at a replacement. i have a few small tanks that i use on a couple pcp. a maurauder, Hatsan bullboss. an fx gun, daystate, etc. my question is, i wonder if the yong heng would suit me or the gx cs3? I have looked at the yong heng for a long time, just hard to decided lol, maintainence is something i def like to to. have you ever used a cs3 ? anyone reading this ?
Thanks for asking, and I agree, it's a difficult decision. Obviously, there are a lot of factors to consider including if you are filling the gun directly or filling a tank. I don't have any experience with the GX CS3, so I can't comment on that. I know the GX CS2 is solid, and I've read good things about the GX CS4. I also know the YH has been my standard work horse for a number of years, and I find it to be dependable and adequate for my needs. I'm sure you will make a good decision for yourself.
I wish I would have found your videos before I went and bought a viver air compressor that burned out after about a year and a 1/2 then I went to buy a hot sun sparc which didn't show up, when it was supposed to, and then when it did show up it was broke straight out of the Box! I think right now because I don't own a tank and for portability I'm going to go ahead and go with the GX, With a 4 year warranty hopefully I won't have to buy another compressor for a few years
5 years on a yong heng change oil every 10 fills on scba bottle 20 minutes at a time 10 minute cool down between with 5 to 10 fills a month from 150 bar to 300 bar aprox.40 minutes total on average ... no complaints
Just a note with the GX, you can fill small tanks with it easily enough but you must work in 5 min intervals, bleed valve, then keep fan running for another couple minutes until cool again. Repeat that cycle as-needed but keep special attention to bleeding the line between cycles as this motor can be damaged if started under pressure. I only have a little 45CI HPA tank but the GX works fine taking me back from 3000psi up 4500.
Thanks! Good to know.
Thank you. Very nice well stated, structured and concise video. I own both also and would not do without either. As will all things, maintenance is part of the pride of ownership. Take care of things and they will usually take care of you.
Thank you very much. Well said!
I own both compressors, Mark and just purchased the new GXCS4 that everyone is raving about. I LOVE my Yong Heng blue box, and I've only used my GX2 twice with zero issues.
Excellent! You'll have to let us know how the GXCS4 goes. I'm curious. Thanks for sharing!
Your videos have good content s ,keep doing them 👍
Thank you very much! I appreciate the encouragement, and certainly enjoy doing these. Thanks for watching!
Very informative, just as I was about to make a mistake.
Great! Thanks for watching.
thank you. Well done.
Thank you for watching!
its a tough decision on compressors, i have an old shoe box that i still use. It is slow , i have one of the first models out and havent did anything to it but replace O rings. I been looking at a replacement. i have a few small tanks that i use on a couple pcp. a maurauder, Hatsan bullboss. an fx gun, daystate, etc. my question is, i wonder if the yong heng would suit me or the gx cs3? I have looked at the yong heng for a long time, just hard to decided lol, maintainence is something i def like to to. have you ever used a cs3 ? anyone reading this ?
Thanks for asking, and I agree, it's a difficult decision. Obviously, there are a lot of factors to consider including if you are filling the gun directly or filling a tank. I don't have any experience with the GX CS3, so I can't comment on that. I know the GX CS2 is solid, and I've read good things about the GX CS4. I also know the YH has been my standard work horse for a number of years, and I find it to be dependable and adequate for my needs. I'm sure you will make a good decision for yourself.
Yong Heng Rocks my 4 PCP Rifles No Problems. 40 seconds per fill 🤘🤘
Rock on! I agree. It’s great.
Hi you seem very knowledgeable just got the SG electric 110 Vevor for my 1 liter tank any good?
I'm sorry to say that I don't have any experience with that compressor nor have I read much about it. Sorry about that. I hope it works great for you.
I wish I would have found your videos before I went and bought a viver air compressor that burned out after about a year and a 1/2 then I went to buy a hot sun sparc which didn't show up, when it was supposed to, and then when it did show up it was broke straight out of the Box!
I think right now because I don't own a tank and for portability I'm going to go ahead and go with the GX, With a 4 year warranty hopefully I won't have to buy another compressor for a few years
That sounds like an excellent idea. I think you will be very pleased with it. I wish you all the best!
5 years on a yong heng change oil every 10 fills on scba bottle 20 minutes at a time 10 minute cool down between with 5 to 10 fills a month from 150 bar to 300 bar aprox.40 minutes total on average ... no complaints
Awesome! Well done!