Vložit
- čas přidán 18. 10. 2022
- Using a Signal Generator - #140
Playing with waveforms!
Need a new meter? - use discount coupon code LE10 and help support the channel!
Kaiweets instruments here: kaiweets.com?sca_ref=1358197.WQbc45IA3a
Lab equipment
Multimeters - Kaiweets KM601 Smart Multimeter
bit.ly/3sP511H
Kaiweets ST600Y Smart Multimeter
bit.ly/3M5Nzii
Clamp Meter - Kaiweets HT206D
bit.ly/3LGBiRl
Oscilloscope (Analog) - Hameg HM 307
• Hameg HM 307 oscillosc...
Oscilloscope (Digital) - Siglent SDS 1104X-E
www.telonic.co.uk/SIGLENT-SDS...
Signal Generator - Junctek JDS8080
www.junteks.com/product/278351124
Function Generator - Siglent SDG 1032X
www.telonic.co.uk/SIGLENT-SDG...
Signal Generator - Rapid Electronics 85-1200
• Rapid Electronics 85 1...
Spectrum Analyser - Siglent SSA 3021X Plus
www.telonic.co.uk/SIGLENT-SSA...
Bench Multimeter - East Tester ET3240
www.easttester.com/a/Product_i...
Bench Multimeter - Simpson Model 465 Series 3
• Simpson Model 465 Seri...
LCR Meter - RuoShui 4090C
victorruoshui.com/productinfo/... - Věda a technologie
Thank you Bill, never ever underestimate as I know you do the importance of ‘basic’. You are a true educator. Regards from an aged teacher
Excelente contenido, muchas gracias por dirigirse a los que tenemos poca experiencia. Saludos desde ciudad de Mexico.
TY
Thumbs up again for an informative video. Have you done one on the tracking generator function of your spectrum analyzer.
Yes, out in the next few weeks!
Здравствуйте, хотел спросить а генератор JUNTEK PSG9080 можно запрограммировать там где программируются последовательность различных сигналов во вкладке FUNC, чтобы работали SWEEP, VCO и модуляция?
Если не знаете, попробуйте пожалуйста, очень нужно знать, делаю выбор.
Hello, I wanted to ask if the JUNTEK PSG9080 generator can be programmed where the sequence of various signals is programmed in the FUNC tab so that SWEEP, VCO and modulation work?
If you don't know, please try, I really need to know, I'm making a choice.
question. I did not understand why the waveform amplitude increased slightly when you touch the metal can.is this sort of like grounding? I know when I touch leads of volume control on radio I get increase in noise.is this similar?
thanks
John
Yes more than likely.
What I want to know is how are the hook ups done from signal generator to oscilloscope? Nobody ever explains that. All the videos I have seen nobody mentions it and shows it.
I use coaxial cable with BNC connectors.
A 50ohm termination at the scope end is a good idea, but for low frequency stuff you don't actually need that. You can still explore waveforms and make some measurements.
@@LockdownElectronics ok, thank you
@@LockdownElectronicsso you just run a bnc cable straight to the scope? You don't use the scope probe at all?
Nice! I need to make a special application signal of one sec length, with different positive and negative amplitude spikes. 5v or less would work for each reoccurring spike, with negative and positive volt being different. Freq is easy but changing the spike amplitudes to different levels is a challenge for me. What do you suggest as I can make a circuit? Integrator circuit perhaps with either a separate limitor chip for positive and negative spikes then rejoin the signals through a mixer? Is there an easier way? Idk
Base is 0 btw and the 1 hertz signal is continuous.
I edited above. The time or hertz between each spike will be mostly 0 until it reaches the opposite spike. For example, a positive spike of 5 volts or less, 0 v, then a negative spike of 5v or less but different the the positive spike, repeated every Hertz.
What is needed to create a 1khz signal at -10db??
Hello. I have a SeeSii AFG that looks identical to the one you have here set for 1kHz sine wave of around 3 volts. Basically the same as the reference signal on the scope itself. I also have a Rigol DS1202Z-E Scope, and it syncs to its 1kHz reference signal just fine. When I plug Channel 1 or 2 out of the function generator into Channel 1 or 2 of the scope, I'm not able to get the signal to sync. It jitters a great deal and won't settle in. I have the scope Trigger set to channel 1 or 2 respectively, rising trigger, and it is adjusted to be in the mid-upper half of the signal, the same as I do for the scope ref signal which works fine. The only way I can get it to lock in is if I attach the trigger out of the function generator to the Ext of the scope and trigger the scope on it. I don't remember ever having trouble doing this before or ever having to tie the generator trigger to the scope. My concern is if my function generator has an issue or not. Both the scope and the generator are brand new. I see other users on here attach their leads to the scope and it come right up just fine. So I'm wondering if I have a bad generator or if I'm missing a setting on my scope, or is there some special condition between a function generator and a scope. Any help would be much appreciated! Thank you for any info you could provide!
Must be nice to afford all brand new equipment 😒
Can this unit be programmed with a math formula, like on a graphing calculator?
I like basic...
Birmingham or Black Country? I'm in the later. I'm a hobbyist working on embedded projects and analogue computers. Good video. Subscribed.
Ditto, born in Wednesbury, accent still there after 32 years in North Yorkshire :)
@@LockdownElectronics I lived in Scorton (near Catterick) for 4 years. Beautiful place that I'm looking to go back to. The dales are beautiful. Tan hill is awesome too, we got stuck up there because of the snow one year.
Am about 9 miles from Scorton!
@@LockdownElectronics Small world!
voice is like Liam Neeson