How to change spark plugs on 2007 Dodge Charger 2.7L V6

This video will show you how to remove intake manifold to access your ignition coils and spark plugs that are underneath the manifold. 2.7L V6 engine from year 2006 and up.

[@Reggied103079]

Best explanation I've seen so far. I'm about to do this at some point this week and changing out all my coils as well. My engine has been shaking a lot when I'm idling and somebody told me that would solve it.

[@marcussmith6313]

Great job! I like how you showed step-by-step actions for manifold removal, hoses, sensors and spark plugs. I'm ready to change my plugs now!! Thank you

[@silverbullet_2ss]

You're very welcome CZcams Fam! Good luck with the process 👍🏾

[@dirkdurant91]

Good video man. Gonna do this to my 2010 charger tomorrow and needed a heads up on how to do it. Thx

[@silverbullet_2ss]

Thanks man! Glad I could help out! Let me know if I missed anything.

[@bensocrazy7264]

Thanks bro. Bout to change out my daughters spark plugs. I’m glad it’s easy to do. How’s that aftermarket part doing? What’s the effect it has on your car?

[@chriskelley5066]

I know this was way past the video that you put out but I want to know what tool you used to unscrew the spark plugs?

[@silverbullet_2ss]

If I recall right, it was a torxbit T25, T27, or T30...🤔 can't remember.

[@chriskelley5066]

@@silverbullet_2ss Thankyou for following up with me.

[@silverbullet_2ss]

@Chris Kelley you're welcome. Thanks for the view. Hope video helps you get the job done.

[@donialsfogg5801]

Good Job my Brother!👍🏽

[@froylanmiranda7362]

Only one concern you didn't cover the intake manifold holes. Other than that I would replace everything under that intake manifold (EGR valve, PCV valve, coils, plugs, gaskets every gaskets. I use pre gapped ngk don't know why parts fail after a year or two on these cars

[@SLINGING_MUD_SINCE1994]

Great job bro

[@silverbullet_2ss]

Thanks CZcams Fam!

[@SLINGING_MUD_SINCE1994]

@@silverbullet_2ss yessir

[@user-sg9tb2hf9i]

Wat socket nd tools are u using to take da spark plugs out with

[@silverbullet_2ss]

@@user-sg9tb2hf9i 5/8 sparkplug socket with 3/8 ratchet and telescoping 🔭 magnet 🧲

[@user-sg9tb2hf9i]

Wat gasket is dem

[@forde.7695]

Whats the ignition coil number order ?

[@juliorenegarcia9863]

Travajo con la misma computadora

[@juli7970]

How similar is this to the process of changing the plugs on an 07 Magnum 2.7 l?

[@silverbullet_2ss]

They are essentially the same car with same engine setup. The differences between them would be minimal and mostly aerodynamics. You got this! 👍🏾

[@juli7970]

@@silverbullet_2ss 👩‍🔧 I just bought the vehicle, should I swap out the coil packs as well? Since I'll already be fussin about in there? Also, great job thanks for being so specific but not overly long-winded!

[@silverbullet_2ss]

@@juli7970 thank you 😊! I really appreciate that! As far as coil packs, I would change them out based off age of vehicle and mileage plus a set of coils is not expensive depending of where you buy them.

[@juli7970]

@@silverbullet_2ss gotcha! 1 more (I think) question:. Can the injectors in cylinders 2,4,or 6 be changed without removing the plastic thing that reads "2.7L V6"? Plennum i think it's called

[@silverbullet_2ss]

@@juli7970 unfortunately no. You'd have to remove it (intake manifold/plenum) in order to access the fuel rails. Then, remove bolts from fuel rails that seat inside the lower intake manifold (black plastic w/ orange gaskets) then you can pop injectors out after that.

[@hectorlucero9158]

Did you use any antiseize or dielectric grease

[@silverbullet_2ss]

I did not. Wouldn't be a bad idea.

[@hectorlucero9158]

@@silverbullet_2ss just changed the spark plugs, video helped a lot thanks man

[@silverbullet_2ss]

@@hectorlucero9158 thank you for watching!

[@rochellej3900]

Who can do mines coming from the u.s 😮

[@rochellej3900]

So serious

[@keil2clean792]

Did the exact but mind want start

[@silverbullet_2ss]

Any luck getting car started?

[@gohardproduct]

I PUT A RAG OVER THAT