I can watch these videos nonstop. You are a wizard man. You definitely earned my sub. I'm also glad I watched you making holsters. I would have had no clue why something like added a flashlight fit would cost more. I knew it didn't use extra kydex to make it more expensive. Now I realize the extra work and time put into things like flashlight and Suppressor sights fitting.
I have watched 30 or more videos on making kydex holster from a whole host of different content makers.i am just getting into making holsters and you are by far the most informative and helpful by far! Thanks so much! Subscribed for sure!
You are a very talented man my friend. Get yourself a KelTec P 17 mold. The gun is getting more popular, especially for us old folks! Let us know I’m ready to buy.
I'm liking your videos. I think it would be interesting to see a dual gun, small of the back, palm out, IWB setup. Preferably for M&P 9 2.0 Compact 3.6" guns. 😉 What are your thoughts on one of those as opposed to two separate holsters behind the back?
One of my very first holsters was a taco for 2 fnx 45s for small.of back lol there's a couple ways to go about it. You can form it and make one holster. Or you can make 2 separate holsters and use a backer to connect them which allows them to flex as well. If I were to do that again, I'd go for the flex for user comfort
learning all I can before I make my first holster. What is the reason for all the blue tape ? Can I set rivets without a press ? I have tools to set rivets in leather. Can I use them for Kydex ?
Blue tape sets the kydex off the firearm so it doesn't scrape. Gives more room. You can set rivets without a press but it's more of a pain and cumbersome
Hey Brotha man, im new to holster making, with the press, i have that same foam, does it matter which side you use? one side is slightly different in texture than the other?
@@FalTacUnlimitedLLC Trying to make it for my sons. One lives in California and the other lives here in Texas. I am just getting into this as a hobby for now. Your videos are very informative and enjoyable, please keep it up. Kelly Gangnath
Nice work. Im looking at making one for my XD-9 with a streamlight TRL-4 on it. Have you made one with that combo yet? Light sticks down past the trigger guard so was wondering how the retention would be.
Started making holsters a month ago, your videos have been extremely helpful.
Hell ya
Thanks, I made holster for my Taurus I'm proud of after watching your vid.
I can watch these videos nonstop. You are a wizard man. You definitely earned my sub. I'm also glad I watched you making holsters. I would have had no clue why something like added a flashlight fit would cost more. I knew it didn't use extra kydex to make it more expensive. Now I realize the extra work and time put into things like flashlight and Suppressor sights fitting.
Definitely a lot behind it. And thank you!
I have watched 30 or more videos on making kydex holster from a whole host of different content makers.i am just getting into making holsters and you are by far the most informative and helpful by far! Thanks so much! Subscribed for sure!
Thank you!
Well thanks to this video I may have found another new hobby on top of my leather work
another great vid Iggy, i learned a few things i'm going to try on my own OWB process...
These videos are the best! Informative plus entertaining, I just placed a order for
You are a very talented man my friend. Get yourself a KelTec P 17 mold. The gun is getting more popular, especially for us old folks!
Let us know I’m ready to buy.
i think i have one lol
Great job sir.
Great video. New subscriber from MA. Like the SpeedEase option. I'll get some in my next knifekits order 👌
Great job again
Nice job dude..!
Nice vid !
Where did you get your spool of spacers?
new sub here..exactly what i need for my M&P 2.0
Appreciate the sub! I still make these left and right
You do a great job!
@@jndred thank you!
I'm liking your videos. I think it would be interesting to see a dual gun, small of the back, palm out, IWB setup. Preferably for M&P 9 2.0 Compact 3.6" guns. 😉 What are your thoughts on one of those as opposed to two separate holsters behind the back?
One of my very first holsters was a taco for 2 fnx 45s for small.of back lol there's a couple ways to go about it. You can form it and make one holster. Or you can make 2 separate holsters and use a backer to connect them which allows them to flex as well. If I were to do that again, I'd go for the flex for user comfort
did you make the jig for the rivet holes? whats the measurement center to center vertically for the rivet holes? thanks
Where did you pick up that rivet setter? Not the press, but the actual two piece thing?
They have the at holstersmith.com and diyholster.com I have a set of each.
Awesome vids! Subbed after 1st vid. I'd love to see u do a full size Desert Eagle 50AE...??
Me too! Done a few. I'll film the next
I love your videos but can you do it with a heat press trying to see what I'm doing wrong thanks
Wow!!!
What size rivets are you using to accommodate for the belt clip hardware?
8-10 Eyelets on everything
Colt cobra 22lr please.
Honestly, I thought I was the only person that dropped everything a dozen times or more during my projects...
Don't you hate that hahaha
So how can I order an owb with an open bottom and 10 degree cant rmr cut and low sweat guard for a g43x like your work
Go to faltacunlimitedllc.com and find the appropriate category. Theres a note section as well. You can add open bottom and 10⁰. And thank you
His website is freaking great. It has me in a kinda kid in a candy store vibe lol
Can you vacuum press, an outside the waistband holster?
Yes. Taco and pancake style. Newer videos have them
How would you work a holster set up for a gun with a thumb safety?
learning all I can before I make my first holster. What is the reason for all the blue tape ? Can I set rivets without a press ? I have tools to set rivets in leather. Can I use them for Kydex ?
Blue tape sets the kydex off the firearm so it doesn't scrape. Gives more room. You can set rivets without a press but it's more of a pain and cumbersome
Hey Iggy. Great job as always. Where can I purchase the ladder bars?
Thanks for your help
Most gun stores carry them. You may also be able to get off amazon.
Hey Brotha man, im new to holster making, with the press, i have that same foam, does it matter which side you use? one side is slightly different in texture than the other?
What are you using there on that spool for your retention spacers?
Part number 65112 on amazon. Continental washer and overflow tubing
Can you make a Taco style own holster for a glock 19
Of course. Email me at faltacunlimited@yahoo.com
@@FalTacUnlimitedLLC
Trying to make it for my sons. One lives in California and the other lives here in Texas. I am just getting into this as a hobby for now. Your videos are very informative and enjoyable, please keep it up.
Kelly Gangnath
@@kellygangnath1399 if you need a shell I can form one and send it to you for you to finish. Another service I offer
The question is, have you ever done a taco holster for outside wear or would you suggest a pancake style?
Another question for you, I have a CZ82 . Could you please do a video on doing a taco or a pancake style holster.
Can u do a revolver like a 357 big frame
I'm sure I'll do one eventually
10 4 bud enjoy the videos
Nice work. Im looking at making one for my XD-9 with a streamlight TRL-4 on it. Have you made one with that combo yet? Light sticks down past the trigger guard so was wondering how the retention would be.
What size barrel xd9. I have like 4 options. But yeah its the same with every handgun. Block the channels for the light and you're gold
What size barrel xd9. I have like 4 options. But yeah its the same with every handgun. Block the channels for the light and you're gold
What size barrel xd9. I have like 4 options. But yeah its the same with every handgun. Block the channels for the light and you're gold
Where can I get that roll of tubing you use for retention bushings?
Amazon. PN 65112 continental wiper/ radiator overflow tubing
What thickness of kydex do you use?
.08 for most.
@@FalTacUnlimitedLLC in inch or cm?
@@netmag2002 inch.
@@FalTacUnlimitedLLC many thanks 🙏
Blocking a revolver for owb?
Easy stuff. When I have a revolver coming up I'll do a vid
SAR CM9 (ie CZ close w/ambi safety)?!?
What thickness are you using? .06 or .08
.08 min. I use .06 when I do dual layers and they're both .06.
what material do these pistol models
?
Fiberglass/aluminum reinforced resin
do yo have any p80 holsters?
Yup. I offer p80s for the 17.19.22.23.32.33.
Listed at Faltacunlimitedllc.com
very nice definition. what type or kind of foam do you use?
www.holstersmith.com/vcom/thermoform-molding-foam-for-kydex-holster-making-mega-form-12x115x1-p-4292.html
Thank you very much
what is the size of your retention bushing?
3/8 usually
What kind of laser engraver do you use?
20 watt raycus fiber
🇧🇷
Do you get all your hardware from knifekits.com?
About 99% of it sometime diy
V💀nd⚰tt⚰