How To Make a Custom Air Intake
Vložit
- čas přidán 3. 08. 2021
- In this video i show how to make an air intake, cold air intake, using spectre parts.
Check out my other videos:
How to do an LS swap / Building a sleeper car:
• HOW TO LS SWAP ANY VEH...
How to wire a switched fuse block:
• How To Wire A SWITCHED...
How to Make Teflon lines (power steering lines):
• How to Convert Hard Fu...
How to do a wheel alignment:
• Front Wheel Alignment ...
How to fix a LS rear main oil seal leak:
• Rear main oil seal Rep...
How to make an LS engine preluber:
• How To Make an LS Engi...
How to change ls rocker arm trunions:
• How to upgrade your LS...
Dakota digital dash Install (1982-1992 Camaro)
• Dakota Digital Dash In...
How to install a 4L60E transmission:
• How To Convert a Stick...
klowny1969 - best car mechanic on youtube
Only clown mechanic in the world ! Uses for an air hammer
This video can be applied to chevy, ford, mustang , impala , camaro , corvette, truck , toyota, lexus , honda , nissan. etc.. volvo cadillac gmc astrovan truck blazer silverado turbocoupe thunderbird clown clowny69 klowny69 GMC Savana 2500 Siera 1500 Sonoma isuzu hombre GMC lsxmatt - Auta a dopravní prostředky
Brianna takes any length of hosing and she never whines or complains. Just like when you were filing the pipe walls. Remember you drill with the tool you got. Brianna must love a sewing machine running wide open ey? Love the vid Bubba and as always take care till next time.
She can be picky sometimes lol Thanks again for watching
That's one nice custom air intake Klowny.
Thanks sir
ALWAYS A PLEASURE TO WATCH GUY
Thank you sir
Nice vid... this is the exact 1 I need for my ls swap
Thanks..domt forget to subscribe
how would I go about making one for my 2016 Chevy Impala 3.6 LTZ, looking to make one and I am going to do the exhaust as well. Thx in advance.
any info is very useful-
this video was great by the way.
I don't have all the tools for cutting and filing but I'm sure I could get some.
Currently looking for some have you looked up the wpn R intake
@@rogeliorivera6572 I have seen that one, but is it any good.will it work without getting any check engine codes
That was awesome
Thanks! Don't forget to subscribe 😉
@@klowny1969 will do. Thanks
Hey Klowny I have the same car and my question is my key on wire loses power during cranking is the any way you made it work with out having to add a push button switch to the starter
Hi..what key on wire are you using? This is a swap that I did here
@@klowny1969 I’m using a red with green wire that came off the coil
Does the grommet come with the intake pipe? Or if you bought it separately do you have a part number? Cheers mate
I had a separate grommet
What size is the piping
4 inch hole she’s been around the block lol
tell me about it lol
What's the part # on the elbow, thanks
I thought I said it in the video?
@@klowny1969 you show the elbow, but I didn't see or hear the part number, I'll watch it again
@@klowny1969 ok. 9781 , I don't know how I missed it, thanks.
Hi.. I need to make this same set up.. what is the info and parts number.. can you list please.. also where to find the grommet thank you
Nice work on the hot air intake with KnN If you get more power it’s from less restriction not air density… just sayin
Lol hot air intake
Where is the turbo LT1 vids bro
I have a twin turbo build