LG Washing Machine No Power $1 Fix
Vložit
- čas přidán 16. 01. 2021
- LG Washing Machine No Power Problem . You can Fix this. Easy step by step repair instructions on how to repair No power washing machine problem . Handy appliance repair video on how to fix this no power error / problem. You can buy the part at www.jaycar.com.au/4-7-ohm-5-w...
- Jak na to + styl
I did the repair noted and my LG is back running again. What a terrific fix. Thank you
This worked. Control board was mounted in the back of the machine and was square instead of rectangular, but otherwise looked somewhat similar. Spinning the drum counter-clockwise lit up the screen. Bought the 5W 4.7 ohm wire wound cement resistor and soldered it in replacing the resistor in the white sleeve next to the fuse. Machine works like new again. This saved a 14-year-old machine that otherwise worked perfectly, and they no longer even manufacture the replacement control board for it. I souced a used control board which turned out to be DOA, so I returned the dead board i bought and as a last resort before buying a new machine attempted this fix on the original control board, reinstalled it, and it works great. Thanks!
I was quoted 267 euros in spain as it would not turn on.. what a legend.. thanks for the fix mate.. turning the drum fixed it like a charm
This video saved me $$$ . Spot on; I did the repair noted and my LG is back running again. What a terrific fix. Thank you
You're welcome!Glad it helped
@@askmrwashywashy hiii did you do this while it is plugged in?
Thank you so much for the quick fix. I spined the drum and all the lights lit up and I could select my cycle again ❤️
Mr washy washy today I had a problem with my washer the same LG as in the video and I must say a very big thank you for your info ! Not even 2 minutes into it my problem was solved not to mention I was fighting with my husband before the solution. Thank you for saving my husband and machine!
Welcome so glad to have helped
Great video! We just purchased a house with an LG washer and two loads in, power failure! We found another video that has a temp fix plus where to order a $200 (US) replacement board. Now I found you and the best fix for less money! Easy fix and no disposing of electronic waste! 👍🏻😉
Thanks. I'm so glad you were able to fix your washer. No electronic waste yes
What is the name of the part, I don’t see the description or name on the site? Thanks in advance.
@@MrVillagrana , not sure what part you’re talking about. There is a link to a part in the description of the video though. On mine all I had to do was power off and follow some instructions to reset the washer. I have not had any problems with it since
I’ve owned a nice Kenmore front loaded washing machine which has been running very well for 13 years. It just lost power last week…
Following your instruction I could fix the exact problem by myself. After replacing the right resistor which I got from a local electronic outlet store the sweet power sound came back on again. And it cost me only 60 cents instead of calling out for service which may cost a lot more. Thanks again.
Awesome so glad to hear you fixed it and you're back washing. Good on you for giving it a go and fixing it
You just saved me thousands of dollars for a new washer. THANK YOU!!
Teníamos este problema por mucho tiempo, y hoy se compuso gracias a ti. Muchas gracias por el consejo estoy seguro que le has ayudado a muchos como a mi
You Mr Washy are a super star. Resistor replaced and working again.
Hello , i have been watching many repair videos as the interest me.
This is the first time i have ever made a comment in all the years.
Reason being my daughter had the same problem and i am in the process of getting the part to fix.
i have tested the resistor and indeed it is faulty =open.
Thanks for the part number as well as we have the same supplier here in Australia.
I am sure it will work, you are brilliant and many thanks for the making of the video.
Greatly appreciated in these tough times have a great and profitable new year.
Hi. I’m so glad you were able to find this video and fix your washer. Hoping you got it going again
I was so apprehensive about the circuit board problem after calling the service center, and they would come in 4 days time in my area!! 😢😢 after few minutes into this video, i tried to turn the drum a few rounds, husband came accidentally push the power button, and it turned on!! How amazing! Tq sir! You have been a tremendous help! 🎉
Welcome glad it helped
Was on hold with the service/warranty provider, so I tried spinning the drum on the LG and it worked!
Thanks for the guide. My model is a WD14023D6 (more like the model on the right that you didn’t disassemble). The resistor in the same position on my model is a 220 Ohm (Red Red Brown Gold) rather than a 4.7k. I measured it with a multimeter and it had 0 ohms resistance. I replaced it and the machine is now working. My model has a brace across the bottom panel so I needed to remove the door assembly as well to gain access to the PCB. Bit more work, but not a bad result for $0.68! Thanks again.
Awesome I am so glad you were able to fix it
@@askmrwashywashydo you think it works in this model as well lg wd-10220fd ;
@@panos920 Guess I can check mine because the washer has water in it, and I cannot spin it fast enough.
This video is SO helpful! Now we know what to check out--and how to do it.
I did mine now and its working.. Thank u for an amzing video.. U safe us!!!! Thank u
Thank you so much! This just happened to me today and I came straight to CZcams to figure it out. Funds are low for our family right now and this totally saved us. Thanks, again!
Welcome I’m so glad you were able to find this and save some money
@@askmrwashywashy Hey Mr Washy Washy! Got a quick question for you. I have an LG front load washer model WM2050CW that requires the control board number EBR38163349. Do you think this little trick will work for this model LG washer? Please let me know. I appreciate your time! :-)
Absolute legend mate. Your videos are brilliant
Hi mate good to see ya again
Great video Mr. Washy. Very interesting and easy to follow the procedures you did.
My first LG washer will be delivered tomorrow, hope not to have many problems with.
You must be a wonderful person, helping others in need or your knowledge.
Thank you. I try to help in any way I can. Congrats on the purchase. You should be ok. Make sure you buy a surge protector and add on extended warranty if you can
@@askmrwashywashy Can you please tell me what brand and model of surge protector should I buy. Washer was delivered in Florida today. The
next leg of the journey will start next week, Florida to Costa Rica via sea
cargo. Hope to have it here in May at a cost of two and a half times what
I paid at Home Depot. Thanks again for your help.
@@horaciocastillo1435 most surge protectors you find in retail stores will do the trick. Not need to buy the really expensive ones
@@askmrwashywashy Thanks for your advise. I do not find them here in this
country but I will try to import one from Amazon. Best regards
Good luck with the LG. Mine was fine for several years but after about 8 yrs, I've been on CZcams looming for repair advice on a regular basis.
I have a WM2250CW and this solution worked perfectly. In my case the resistor was a 110 Ohms. Thanks a lot!
I have the same model number. The control board looks a little different than in the video. Is the resistor at the bottom near the fuse? Also, do you recommend a certain type of 110k resistor or will any 110k 1/4 watt 5% work?
@@pjnoon9578 not 110k, 110 ohms!!! But check the existing resistor based on colour coding, mine is 110, yours might be different (even with same model nr). I didn't put 1/4watts, I replaced with a 5watt one, for reliability
SIMPLY FANTASTIC! Thank you Mr Washy! Folks, as always make sure you use plenty of soldering flux and clean your soldering iron!
Welcome glad it helped
Just a follow up, Mr Washy Washy. Now that I think about it...resistors do not usually burn out (they are not fuses). And there are others videos out there illustrating that a fix can be had by holding the on/off and pause buttons for 5 sec each in sequence (whilst unplugged) resets the machine. Would you care to elaborate or comment on this, please?
Replaced the resistor, machine now works. Thanks!
Glad it helped
Great video! 68c for a washing machine fix 🙏 Appreciate the help mate.
Glad it helped
Thank you Mr... like less than a week ago the electric source socket plug was successfully repaired as tested using the plug washer light was on . But today how frustrating it didnt work ..pressing the power button several multiple times neither the light nor the washer intro sound were there.
For almost an hour searching for solution over youtube was pretty challenging when other side of the globe video posts having same issues with lg washer panel that it has to be taken of to check on the circuit or motherboard thing mostly for different models and looks like a task of technician. But upon the 1st try of your simple suggested step.. it works so amazing like a magic trick🌝🌟🌟🌟
Its actually lg top load washer by which buttons panel set also on top in front the washer door.
Welcome so go glad it worked out for you
I had same problem but it was the bad noise filter. But great video. I see you helped so many people already. I would suggest others that check the noise filter and door switch before touching the mother board.
Cheers. Yes some LG noise filters do that. Haven’t seen them fail lately though. Thanks for sharing, I’ll use that noise filter trick sometime
How to check the noisy filter and the door switch
@Santosh Sharma, how to check the noise filter and door switch?
@@akamal3 I used a multimeter. There are tones of videos how to diagnose an electronic component with multimeter. It is very simple. The noise filter is usually the first electronic components the electric cable goes through. Door switch is located at the door lock. You can check that too same way.
Same exact issue with my lg tromm front load washer. Machine turned on now and starts to wash then after about 45 seconds trips the breaker. What can it be now?
Great video
I have a direct drive model WM3987HW which went off in the middle of operation and would not power on again.
I turned the drum as demonstrated in the video and no sign of power generated by the motor.
Hope you can help with what I need to do.
I opened and found something on the noise filter looking bad.
Thanx.
Great video! I did this and no light but smoke started exiting from the board. My board is different on my LG wm2277hw model but there’s a very similar part that looks a bit brown. I think that’s what was smoking. Should I replace the part? Or would this smoke mean a different issue?
Many t😀hanks for the 1st tip! I tried to take out all the clothes and turn the drum for a few rounds, then the board is lighting!
Great Video will this also work on on LG model WM3001HRA? Thank you
Hi there, just watched your video on the LG washing machine repair, I have an LG tumble dryer very similar to looking to this machine you have repaired actually we have the same washing machine as this one, have you done any repairs on the tumble dryers same problem won’t switch on thanks Bill.
You are a suowr great teacher. The device you cut out and changed. What is it and what is the ratings on it? Thank you very much.
I had the same problem as you did. My model is WM2250CW. Could you tell me if I should buy the part: 4.7 Ohm 5 Watt Wire Wound Resistor?
Thanks bro. Wish you the best in your career and life 😊🙏🏻
welcome. hoping it helped you out
@@askmrwashywashy shour..I just fix my LG washing machine according to your advice and saved 50$ approximately 👍❤
Hey Mr Washy Washy I have an LG WM2301HR model that won’t turn on. The power filter board fuse was blown so I replaced it but it still won’t turn on. A repair guy said the interface control board was bad so I replaced that. Washer still won’t turn on. Do you have an idea what it could be?
My washing machine (LG direct drive) suddenly stopped coming on about a week ago without giving any prior signs. It has been working perfectly for about 5 years now. I have tried spinning the drum like you stated earlier, but it didn’t come on. Is it worth trying to replace the resistor?
I had a no power problem with an LG dryer. Because of your video, I checked the fuse, which also was semi solid state in resin on the ic board, sure enough it was blown. Dug it out of the resin, soldered in a new one, Bingo! However, it cost me over $3.00, then again is was CAD, so probably closer to $1.00.
Thanks so much. I spinned the drum and it worked
My power button, wash selections, and pause button do not work when pressed. However every selection on the control panel to the right is lit up. Including child lock and wash delay. Any advice.
Hello i havz a question as im having problems with my LG washing machine.
When i press the Button ON the volatge tester from red become green. Frim what i understand the problem in my case is the front control board?
If the resister is blown but the lights don’t come on when you spin the drum does it still make sense to replace the resistor?
Hi Mr. Washy Washy i have a LG WM8100HVA. i have exactly the same problem with the power, when I spin it mysleft the light come up and shut down again. I m not sure the wire wound resistor I need for this model. please help. Thx again
You're the best, mate. It worked. Thanks for everything.
You're welcome! Glad it worked
Any idea what amp the fuse is on the board? My fuse is blown.
Hello. Thanks for the video. I have the same issue with my washing machine, the resistor is a 220ohms (red red brown gold) on mine at this same position on the board. The value is good. Any other tips or things to look at? The power goes to the control board, the switch command goes to the main board too (tested following the wires) but it doesn't power up... Many thanks for the video again
I have a lg wm2650hwa. If I spin it there is no lights and sound, but I can unplug and hold down the power then the start button and replug it and it will work. Can I still follow your steps as a permanent fix?? Thank you!
These front loaders are so complicated with all the circuit boards it’s very nice to get these tips to get us closer to repairing them for our self and other s thank you
welcome. trying my best to share whatever knowledge I get on these. Hopefully people can save time and money
@@askmrwashywashy
Great video, thanks for uploading.
Question,,
Our machine is like the model on the right side..
Things lite up and sometimes appears the code lack of power and sometimes hall sensor defect..
Machine allows water coming in and also pumps it out,, apart from that it's gone bananas.
I'm living in Brazil and in our region there are no trustful mechanics available,,
However we had one who said that the hall sensor is ok (even while the error appears). The wire looks neat no visible defects as I can see,, now the mechanic said it's the pcb board and 2 pumps need to be replaced.
Wonder if the machine has 2 pumps, but even if true one of them is working.
Do you have a suggestion where to go from here ??
In any case thanks a lot
John
I have a LG washer dryer combo like the 1st machine I get it all working except I get no display on the screen it backlights up just no numbers or anything
I have an older model: WM2016CW - I have to unplug it to reset it, then once it's reset it'll run a cycle fine. After the cycle it powers off again until I unplug it. After I reset it, spinning the drum will power the unit on. When it needs a reset, then spinning the drum doesn't fix it. Is it possible it's a resistor like this? Do you have any idea what that resistor does?
My model has the MCB at the back, top left. This "need to unplug to reset" problem seems to be pretty common, but I can't find anyone who knows why or what on the MCB is causing the problem.
Beautiful , congratulations mister !😊
I got the same problem with Samsung washing machine, works only when i spin the drum.Can i get any help regarding which component to change in the main board? "The board is mounted on front panel"
Where is the store located that you placed link to that resistor? Will they deliver to US?
Omgoodness! Thank you! Same thing happened to me today! & it worked! Thank you!🥳
welcome glad it helped
Thank you for posting this! It solved my issue!
Glad it helped!
Thank you! This saved me a prity penny 😊
I have the model on the right. Today all of a sudden water was leaking from the bottom of the washer. Mopped it all up. Cleaned the filter and the drain hose that connects to under the sink. Tried it again on a short wash and again im getting water leaking out from bottom and its at the start of the wash.
I also have a noisy drum.
Its out of its 5 yr warranty but it's still within the "10yr direct drive warranty"
Id appreciate any help as im not in the position for a new washer dryer.
I have emailed LG.
Ive had a noisy drum for few weeks now but water only started leaking today
Great video, and very informative. I have an LG Washer WM2701HV with no power, and there isn't a "motherboard" in the base. Have tried the power down, two button reset with no luck. Now trying other steps to resolve the issue. Any thoughts/feedback relative to this particular model to get it back to life is appreciated. Thanks!
Hi there I think yours is at the back on top
My machine looks exactly like the one you are working on but on mine the motherboard is under top lid. No discription below for what part and what part you kinda tapped your screwdriver around at some parts but which one?
Mr. Washy, I have the same problem with a bad resistor. I physically checked the resistor and it was fried and cracked. Are all the resistors have the same value (5W 4.7ohms) at that location as mentioned in your video. My main board is EBR74282001. Please advise.
My model is LG FH2G8QDY5 and it won't lit up. Upon turning the drum however, its working. How can I know which part to replace?
Thank you in advance
Thank you so much, this worked like a charm!
welcome glad it worked out
@@askmrwashywashy
My LG Tromm WH2487HMD washer will power up, start then go dead again. I replaced the mother board and it worked for half load then power went out again. I just spun the drum and it powers up and then goes out again. Having already replaced the mother board and noise censor…what’s next. My wife is about to divorce me but I feel like it’s got to be something simple. Could it be the door switch? I don’t get any error codes. Can you help?
What is the actual value of resistance for the model number F1403YD25 LG Machine .
Great Video!! Thanks!
Why is the 220 Ohm resister replaced with a 4.7 Ohm resistor? Thank you
Hi. My top loader won’t turn on at all. This method and the reset don’t work. Am I up for a new washer?
Excellent commentary I learnt allot cheers
Welcome glad it helped
@@askmrwashywashy Hi great vid, followed your instructions got lcd to flicker only no other sounds or lights could it still be the same fix LG F1443KDS - Thanks
@@amerlatif4100 hi yes change that resistor and it should work
I have LG WD1200D Inverter Direct Drive 7kg & did exactly how he showed n it works!! 👍
Awesome glad it helped
I cannot spin the drum fast enough because it still has water in it. Can I use a vom and check the fuse?
Nice video, thanks.
Thanks a lot Sir. This is a really great video
Welcome glad it helped
many thanks, yr great. I could fix the problem according to yr instructions.
Welcome glad it worked
We leveled ours and it is working at the lightest touch like new. Installation was done incorrectly. Before you call someone do the ThinQ as we did. It helps to diagnose problems. You for sure know it’s not the expensive parts, which the people who looked at it wanted to replace.
Awesome I’m glad it’s fixed now. Well done
Excellent video! For the resistor, can I actually get one with a higher Resistance level than a 4.7 ohm?
I’d try to stay as close to 4.7ohms as possible
Thank so much for this video it's helpful..
welcome so glad it helped
good presentation and detailed. ECT
Thanks for your sharing.
Do you have a video for a samsung front load washer that wont go on?
Hey Mr Washy, I have a WM3997HWA Front Load Washer/Dryer Combo, Mine failed right at the start of a Wash cycle, so the Drum has water in it, I did Drain it, but Im unable to spin the Drum fast enough to get any leds flash. Have you repaired any of these 2in1s before? Should I try the Same thing seen in this Video?
Hi it should be the same principle. The direct drive motor is what will power the board when you turn it by hand. If still under warranty contact Lg for repair. If not check the power board. Yours should be at the back at the top. Usually if it does not light up when you rotate by hand you might need a new board
Will this work with a LG washer machine Model: WT7800CV?
Very good IAM a technician of washing machine in Bangalore India
helpful. same part is a common issue in ryobi battery chargers 😅
Thank you for the video
God bless you sir... But in my case, between the black and yellow relay on the mother board keeps clicking..
What should I do sir... Thank you
I've got a Samsung DirectDrive (rather than a LG model) that likewise will not turn on. Would this same fix here apply to a Samsung make of machine? Or is there a separate video that deals with Samsung?
Hi my LG F1289TD Washing machine whole display was erratically and stopped and won't turn on. I will do you test thanks
Okay, so this is the 2nd "quick fix" video that did not work for me. Seems to be a bit of resistance when I try to spin the tub. Not sure what the issue is.
thanks bro, it really worked👍
welcome im so glad you sorted it out
thanks for sharing...good job...
Thanks for watching!
Thanks bro ibwill try it tomorrow.. im an electronics tech.
Very helpful..God bless you
Glad it was helpful!
Thank you in deed. Salut from Türkiye.
I'm having the same issue on a 2007 Whirlpool duet dryer, have you done any "cheap fix" videos on them. Id rather not buy a new/used control board.
hi no experience with those sorry
WM3550HVCA with PF error, spinning the drum would not light up anything. Took the board out anyways and tested the resistor and it was open circuit. Replaced with 4.7 ohm 5w and it blew right away when i plugged in and pressed power. Unfortunately the board is potted so component diagnosis is difficult. Is there another thing i might be missing? Seems a wasteful shame to throw away an entire unit because some small component might be faulty.
Hi not much you can do but buy a new board. Usually if its blowing the resistor straight away it has blown a transistor too . Haven't had much luck replacing those. Sad, your washer is a great big size.
Nice work brother
Hey there Mr. Washy! When I plug my dead LG washer in and spin the drum I do not get it to turn on momentarily, but did manage to produce a whiff of smoke from the circuit marked "1252 TOP243YN 0R2*SA" (the asterisk is a number that appears to have a burn mark on it). This is a circuit/transistor that is in what looks like a heatsink. Any idea if this is replaceable and where one can get it? Am I out of luck because of the silicone that LG encases the circuit board in? Thanks!
hi mate. yeah that silicone makes it really hard to fix the Board. That part might be a power management chip. Bosch has them on their washers and they usually blow out.
Mr Washy, I got a blown Power IC/Transistor on a heat sink as he explained......any advice if to proceed with repair as this would require taking out the whole gel from the board to get it out and replace "1348 TOP 246YN"
Hello, could you help me, can I use the same resistance as the link you left? or do I need one of another size this is the model of my washing machine model: wm2301hs
Hi try and match it to the one on your washer
Hello my washing machine is LG 9kg the problem is no power, but I follow your instruction to open the door and spin and when I spin nothing happen to the light what you shown before, is there another problem? Or it is the same way that you do I change the part like what you change?
Hi you would need to change the computer in your case
Lg wm2455hw do i use the same replacement my resistor blew the other day
Hi check what colours are on your one if possible.
on checking for power from the box, I swap the dryer and washer plugs.
My washer is the one on the right. It turned on for a second when i spun the drum. What is the fix for this??