Video

This was the most detailed video for my new LG combo. Thank you. I do have a question. I'm struggling to figure out how to remove clothes after a wash cycle and then return some items for drying. My settings are a bit different than the 2022 model shown in this video. I have a 2024 model but the manual states it's for 2021-2024. Any feedback would be appreciated. I bought the LG to replace a Malber combo that I had for 22 years. It was a lot simpler but a great machine. I'm hoping that this LG combo is as good. Thank you, again.

Thank you for the tutorial,my washing machine came in german and it was hellish trying to understand what was written on it without ur tutorial

Thanks alot for this video, saved me a bunch of money aswell. One thing i made the mistake of doing was pulling the door glass seal out, mine was full of lint and i should have just washed it but i assumed i could remove, clean and replace. But unfortunately the seal is not able to be put back in! The door needs to be disassembled and it is designed not to be. You cant buy just a seal only a whole door. do not remove the door seal people!

Great video for taking apart - mind isn’t drying, found some lint but not much realy it’s 6 years old and constant use as I’m 70 use it everyday. But I don’t know how to remove the condenser or if it’s the problem of a heating element. Repair guy wanted $650 to remove condenser and acid wash it. Didn’t have faith that it was the condenser and thought it too expensive so now without a dryer. Any instruction as to how to remove condenser and check the heating would be greatly appreciated.

Samsung WW90T3040BS I'm a female please help, I will buy the screw drivers today

Hiii... im already calibrate but it shows pause.... how can i solve it?

The little hose beside the filter , pull it out and drain in a bowl before removing the filter. No mess.

The machine is hot so i turned it off . But I cannot open the door what shall i do?

Pls reply

I cannot open the door. Shall I turn on andtap the start pause?

Thank you. I rapaired my machine with this video.

How you activate the light? Thank's for answer.

Many thanks so clear

Sir what pot d sofreír in condiciones

Hi I need ur help

Many thanks for your very clear video. Maybe you can show ‘putting the brushes the right way’ a little bit clearly and in slow Motion. We were not completely sure that we put them in de right way. There was some noise in the beginning but that dissapeared.

How do you fix error 2

Thanks mate!

When red light flashes with E10, I push the the start button, and the washing machine starts again normally . Would you please advise what I have to do. Thank you

Many thanks Did what you you said and BOOM goes like a charm Many thanks Pk from NZ

Tip: I had real trouble getting the wire seal retainer in place. I wiped the wire with dish washing liquid to act as a lubricate. That made the job a lot easier.

It’s not draining, and LE error. Ideas.

Hey, how do you get the dryer hot?

So, no blankets no duvets... But the washing machine has a DUVET programme.!🤔 And what did you say around 3:15? Am I missing something???

Yessirrr

Nice one my Guy

Thank u. Info very usrful

Really good video. The bottom plastic panel comes straight out. Not up, not down, just a straight pull. For the seal, I found it easier to fit the inner seal first, then the outer seal just seemed to drop in place. I also found it easier to remove the three screws (top) that hold the softener box in place. Makes it easier to remove/refit the front control panel.

I have the older model but have been offered this one through insurance … does it still play a song when it ends

What model number is the dryer similar to this washer?

great fix! didn't even need the water step (which is best since im on the 18th floor and my maintenance crew refuses to answer my tickets) so this was a perfect stealth fix

Great video!

I bet your washer is about the same age as mine. The spin cycle throws off that little piece of plastic; even on a balanced washer.

Le wath stand for

Hi I have same machine pcb.problem is drain moter start as soon as machine power on and start drain water .please advice how to reapir this fault.

Hello Quick Q @ 3.44, when you say "if the power doesn't go off" .... Did you actually mean... "if the power doesn't turn on..." ? Thank you! - AB in Santa Barbara California

Thank you!!

Thank You Sir! subbed.

Great Vídeo... Thank you 🙂

Thank you very much. My washing machine was a Hoover and it was tripping power. After disconnecting the heater like you showed, it stopped tripping power. Thank you very much;you just saved my pocket.

Have this exact same model, with the exact same issue. So I followed your video instructions (and thank you very much for these by the way; I would not have had any clue how to disassemble without coming a cropper!) and opened up the catchment to gain access to the heat exchanger. Only to have NO fluff or lint buildup whatsoever. In the absence of any lint, fluff or gunge, what else could be responsible for the lack of drying?

We did exactly what you said and bought the new sensor part and installed it. And the machine still comes up with the E3 error code. We then placed the old sensor part in another Bosch Maxx machine just to check it. It worked, so it’s not the sensor. What else could be causing the E3 error code?

I had this machine It died not long ago in march bearing seal failed and it had Leaked for a long time by the rust I found. Wasn’t put off as was probably my fault for not de scaling it enough I was told. Anyway got the new LG washer dryer and it’s great, But I couldn’t find one video on this issue it makes it look like the screen is gone but it’s just that black thing happened twice to me with that model fh4u2 range I fixed with sellotape and if I see this someone on fb selling their machine because they think its broken I tell them that it’s just this little black piece of thick film and 20 mins of there time. You will save 100s of LG machines going to landfill because of this little issue I solute you as like I said I couldn’t find 1 video 2 years ago for this, just board replacement videos. Well done man.

Couldn’t find a video on my neighbours logix washing machine think it’s a vestel machine under that brand. It kept overfilling near enough to the top of the door then e12 would come up and beep I done what you said blew down the pipe and I also blew into the pressure switch put it all back together and now it’s working fine again and stoping the water at more appropriate level. How it didn’t flood I do not know. Great video thought she needed a new pressure switch but it’s fine now something flew out of it when I pulled it off.

Madre mía si hay que desmontarla prácticamente toda😮si mi marido me hace eso ya la puedo tirar ,por qué no sabremos volver a montarla 😅

Thank you

My 9 year old dryer is as new after 3 hours work. Also rinsed the whole section and cleaned the pump area. Thank you for saving me 900 euros for a new one ;)

Thanks a LOT for this walkthrough! I've finally decided it's time to clean up mine (after nearly 8 years of daily usage and coming to a point where I had to put it through four or five cycles to dry clothes like 80%) and oh boy was it full of dust and lint. Much worse than in this video. Oops 😅Thanks again mate, my dryer now works great again. Note that you can also remove the panel below the two radiators which exposes the bottom and in my dryer it was full of black sludge. I cleaned that as well.

On early machines there was a filter screen prior to the condenser units, easy to clean. This is no longer in the new machines hence dry lint/dust covering everything, get a piece of foam people in front, should keep the rear clean

Thanks. If it's leaking from the front what has this valve got to do with it? I don't understand the link?