hi, i burnt a bc204 plug in into DC, i know i'm stupid as hell. opening it i see a capacitor 47uf exploded and the ''u7'' component also a little burnt, taking pictures i saw (the letters that remain) says something that 509 on the first row, E1 in the second row and 9 on the third row. i don't know if i can replace them or i'm totally over. Thanks in advice
i'm pretty shure that the component i'm talking about is the one that comes after ch3 on the BC216. U1 i think. being C2 the capacitor one that exploded. is that component available?
Hello I accidently short-circuit one of the SPI connection with a led that was wrongly wire. The SPI output do not respond anymore, do you know which piece to change on the board to fix that ?
If you open up the unit there are “automotive” type fuses inside, unplug the unit, set your multimeter to continuity, and check every fuse with it, then replace blown fuse. You can buy those fuses in any car shop.
Hi, I have BC-216 and probably short-circuited on of the ports. Now only the first pixel on every led strips lights constantly and test mode does not work. The menus and connection from my computer is still working. All the fuses inside is tested and working. Any suggestion if it is repairable and which part is causing this?
Thanks for the quick reply :) I will have someone professional to test this. Can I buy IC directly from your store if I also buy something else or another BC-216 unit? Tried to google a IC number "94 A7P1K G4 HCT245" but did not find anything(not my field).
Sorry I replied to wrong comment. Unfortunately I don’t have a store. Hopefully in the future once my channel grows. Have you scoped out the signal from the port to the processor?
Hello, I have question, can you help me with product BC-216 artnet? The connection was broken during the update and lcd screen frozen on "Update the firmware" and its not working. Can you help me?
Hi, you will have to upload firmware through programming port located on the right side on the main board, you will need: a programmer for arm processors, firmware, and some knowledge in programming. Then you can attach the programmer to four pins just on the right of the arm processor, they are 4 vertical holes they would fit Dupond connector. And flush new firmware onto the chip.
@@MaxELECTRONICS Its look like complicated way :D Can I just someway restart all device or restore to factory settings? But I have other question, where can I download latest firmware fot BC-216?
No unfortunately if your firmware is corrupt you have to re-flush through the programmer. Also I had a look I can’t find firmware ether, I don’t know who the manufacturer is, I think it’s genetic device, meaning it’s made in small factory in China and very hard to trace who makes it.
sir..can you help me with this unit?i just buy it and i can't connect it to resolume...i checked up my adapter setting in my pc it says "unidentified network"...so i run the diagnostic but it keep saying no valid ip config... i use win 10..thanx before..
@@MaxELECTRONICS i've try using both router and crossover cable..but it still won't connect...it keep saying unidentified..when i diagnose it say does not have a valid ip configuration...any suggestion?
hi, i burnt a bc204 plug in into DC, i know i'm stupid as hell. opening it i see a capacitor 47uf exploded and the ''u7'' component also a little burnt, taking pictures i saw (the letters that remain) says something that 509 on the first row, E1 in the second row and 9 on the third row. i don't know if i can replace them or i'm totally over. Thanks in advice
i'm pretty shure that the component i'm talking about is the one that comes after ch3 on the BC216. U1 i think. being C2 the capacitor one that exploded. is that component available?
i'm pretty shure that is a XL150 IC, but i'm not shure if it is a XL1509-ADJ E1 or XL1509-5.0 E1
The ic is XL1509 -5.0 E1
Hello I accidently short-circuit one of the SPI connection with a led that was wrongly wire. The SPI output do not respond anymore, do you know which piece to change on the board to fix that ?
If you open up the unit there are “automotive” type fuses inside, unplug the unit, set your multimeter to continuity, and check every fuse with it, then replace blown fuse. You can buy those fuses in any car shop.
@@MaxELECTRONICS thank you !
Hello , it s ok for stripper led 5 volts ws2812b ? Thank you
Hello, yes, WS2812b led strips are 5 volts,
Do you have stock for this?
What do you mean?
Hi ! The Driver to Update It Is Asking Me For A Binary File That I Don't Have, Where Can I Download It? Thanks..
Hi, Unfortunately there’s no update, I couldn’t find it anywhere.
Can we use this unit with MadMapper and Resolume?
If they support “artnet” then yes
Hi, I have BC-216 and probably short-circuited on of the ports. Now only the first pixel on every led strips lights constantly and test mode does not work. The menus and connection from my computer is still working. All the fuses inside is tested and working. Any suggestion if it is repairable and which part is causing this?
It sounds like it’s the controller ic or the I think shift registers I think
Try using oscilloscope and trace the signal in test mode, work backwards from port to the controller IC
Thanks for the quick reply :) I will have someone professional to test this. Can I buy IC directly from your store if I also buy something else or another BC-216 unit? Tried to google a IC number "94 A7P1K G4 HCT245" but did not find anything(not my field).
@@MaxELECTRONICS Thanks, but this is regarding BC-216 and not the DR-05 ☺️
Sorry I replied to wrong comment. Unfortunately I don’t have a store. Hopefully in the future once my channel grows. Have you scoped out the signal from the port to the processor?
Hello, I have question, can you help me with product BC-216 artnet? The connection was broken during the update and lcd screen frozen on "Update the firmware" and its not working. Can you help me?
Hi, you will have to upload firmware through programming port located on the right side on the main board, you will need: a programmer for arm processors, firmware, and some knowledge in programming. Then you can attach the programmer to four pins just on the right of the arm processor, they are 4 vertical holes they would fit Dupond connector. And flush new firmware onto the chip.
@@MaxELECTRONICS Its look like complicated way :D Can I just someway restart all device or restore to factory settings? But I have other question, where can I download latest firmware fot BC-216?
No unfortunately if your firmware is corrupt you have to re-flush through the programmer.
Also I had a look I can’t find firmware ether, I don’t know who the manufacturer is, I think it’s genetic device, meaning it’s made in small factory in China and very hard to trace who makes it.
sir..can you help me with this unit?i just buy it and i can't connect it to resolume...i checked up my adapter setting in my pc it says "unidentified network"...so i run the diagnostic but it keep saying no valid ip config... i use win 10..thanx before..
Try plugging it into a router or Ethernet switch, also if you connecting to pc, are you using patch cable or crossover cable?
@@MaxELECTRONICS i will try using a router..i'm using a CAT6 cable i bought at local computer store...is that okay? Using cat6 cable?
Yes but it needs do be crossover if you plugged in directly into computer
@@MaxELECTRONICS i've try using both router and crossover cable..but it still won't connect...it keep saying unidentified..when i diagnose it say does not have a valid ip configuration...any suggestion?
Have you tried connecting it to the router? Also try to setup the controller in DHCP mode and then try manual mode with manual address
somebody know where to buy this now " not from china" ?