Video

Thanks for the video 👍

Hello, how bright should the leds be?

Hello how can I get pcb

So how do you “unspring” a coil, make long and straight again? Just same concept?

do you ever use this with liquid pcb solder mask ink ?

driveที่สองอะไรกูงงมากกูเห็นแต่มึ่งใส่driveเดียวแล้วก็ปิดฝา

Great demonstration. I'm looking to replace some bga memory chips and im watching videos to figure out how

Where is possible to buy laptop cpu chipset? Cause I’m looking for it everywhere online but nothing

thanks for the breakdown✌️

This is for those with experience fixing circuit boards. Question is it possible the moisture from the trash will rust out any circuit board.

This is wonderful

Hi Max, brilliant video, very detailed. I have a ceiling mounted epson tw7300 projector that shows a vertical blue one third left of the screen. This line appears after a few minutes of use and generally on bright mode. It clears off while using digital cinema setting. Line appears quite late when room is cold. When I play a video of full blue screen, there is no line but is immediately visible when blue screen clears off. Line shows up as blue on black screen and shows us as pink on red screen. Any thoughts which part could be faulty? Thanks in advance

Gracias por desvelar el secreto de enrollar un cable correctamente

Epson tw7300, I have a bit of red bloom in black and white (text area) but only at the top and it's very very faint.. so I wanna prepare myself and know if it will also be the same polarizer located in the prims that I would need to replace,

Nice work. I love the tip that you spray water on the PCB before putting on the Dry Film to make it easy to get out air bubbles - thank you. With Step 5 - Is Soda Ash (pH Increaser) do the same thing?

Is it possible to just add solder to the bord and chip then heat up rather than reballing?

I’ve googled for hours can’t find my head unit resistance wiring diagram. Boss BE7ACP

I want to use L3P08 L3P09 L3P010 instead of LCX111 LCX124 LCX101 LC080 in projectors is there any method or software that I can use

Hi, Thanks for all the helpful videos, and for the detail you give. I have a BENQ PB6110, with the same regulator, damaged in exactly the same way. I know this video goes back some time, and hope you'll still be able to help me.. do you know if that regulator has any other or equivalent codes.. I'm in South Africa, and components are pretty hard to source. Hope you can help.. Thanks again for the great videos.

Marvelous!! You're great to listen to while going through the repair and your voice is quite like even entertaining. Good job bro.

question I get no disk now, even with the original drive. I suspect ribbon Cable , Thoughts?

Nice solution! What is the NTC value? Thanks buddy.

😊

Another amazing idea.

it's been a very long time since I was amazed. Thank you for sharing with us!

Can i connect an amplifier?

Hi amazing video where do you buy the stencil and support for the chip

Did anybody notice that he caught a "Mosquito" @7:00...🤔🤔🤔

I've the same model 7018b, but not open the any logo!! do have update for version?

About 3 years ago a friend of mine gave me his DR05 with a broken display asking me if I can fix it. Of course I told him to just forget about it after I searched for a replacement display that would fit and nothing came up. Then after a few days you uploaded this video and I was lucky enough to find it. I put the display from your link in the basket on Aliexpress and it stayed there these 3 years, never had the time and will to do the job and eventually forgot about it... just some weeks ago I found the Tascam in a box ready to be thrown along other scraps. But said hey, let's give it a chance. So the display was still available and was waiting for me in the basket, ordered it and it arrived in less than 2 weeks (from China to Romania); it came very nicely packaged, I was actually amazed, thumbs up for the seller. Installed it yesterday, not an easy task for less experienced people as those pins are tiny and you need proper equipment and a decent amount of skill to attempt this repair. I used some textile tape and hotglue to make the new screen fit better and stay more securely in place. Dettaching the new screen from its backlight plate was the most intense part lol. So yeah, the screen is alive and the recorder will soon be reunited with its owner. I'm not even charging for the repair, not only because he is a friend, but because the succesful repair itself was very very rewarding. So we would like to thank you for this tutorial, for the time you spent documenting this repair and for offering one more chance to these otherwise doomed devices. You are awesome sir!

Looking for a little help. I have a Pioneer VSX-453 receiver I just bought. The right channel is staticky and distorted, but am getting power decent power. I cleaned the pots and boards. It still sounds like that. Left channel is fine.

Hi! Maybe do you know if a Sony HRV-Z1e has a kind of fuse inside? Once I put a battery turned on and off and died, even pushing reset button or, of course, trying again with another battery or charger. Seems unbelievable that this camera hadn't any protection... Thanx!

Ordening the PCB by re-uploading the files is not the best way to go. PCBway has a project section where the developer can upload the design for others to easily order. Can you upload your project in the same way? Thanks!

Nice! Can I put two in series so you have 12V and 24V? Some POE switches run on 24V some on 12V. The security cam NVR also runs on 24V.

Could you please post a link to the LED chip replacement that you used for this video? Thx!!

Thanks, Max for your detailed explanation in this CZcams video. However, I would like to know what you think about the full purplish imaging projected from my 6 years ago Sony VPL-HW40ES projector. Please provide me with your opinion for this case. Thanks.

My MCX8000 has been a right pain. Stutter button has the same problem, the switch on the line fader has broken off. It’s already been sent off to InMusic because MCU Display was faulty, when it came back it lasted 3 months then broke again. I was without the decks for a whole summer as they had to wait for the parts. But tbf I find it works better without it, just use a laptop instead! I want to take it a part but I probably mess it up even more 🙄

hey man did you started selling them?

Great work. Thank you

Are the start and stop buttons momentary switches or constant?

I can’t get any of my Radio stations equalizer or clock to stay set , ever time I turn off car everything I set goes away .. does anyone know how to make them stay ?

have you tried connecting the pc410 with a computer? i tried it using RS232 and the PSOFT Rework Station Controller application but the result cannot be connected, maybe you can share if you have experienced it, thank you.

hola castillo tengo un EPSON EH-TW6700 parpadea la luz azul pero no da claridad a la lampara pero tampoco da falla de lampara ni de

do you have any links to some of the tools you used during this process, specifically the templates, chip holder etc. even the BGA station

me encanto justo lo que necesitaba saber para hacer la mia

hi, very informative video. Do you know if chineese head unit devices do in the same principle? There only KEY1 (and KEY2) wires, no 3.5 jack for SWC. What voltage they are using?

Genuinely informative video man, but your diagramming had me flinching. Reminded me of a doctors script haha! Maybe take it a bit slower and dont use so much shorthand when youre drawing something to explain a new concept. Cheers

This video is great; thanks for sharing this with the world. I've found that good flux, patience, and a light touch with the iron and braid is the way to go. Here's an extra tip - clean the flux off with alcohol when the surface is still warm. Makes it much easier. If the part or board cools and the flux gets gummy or solid, add more liquid flux and rub lightly. It will help soften up the hardened flux, allowing you to get some alcohol and clean the area easily. Thanks again for this video 👍

Just wondering. Is this cable schematic also same with Blackmagic intensity Pro, the version before Blackmagic Intensity Pro 4K? Cause I bought the Blackmagic Intensity Pro only just the card without the breakout cable 😢

does it come with bluetooth?