Spudski RC How To: Calibrating the ESC to transmitter on Arrma Big Rock 3s range and 6s

#Arrma #Bigrock #Typhon #Granite #Senton #3s
This is a video how to calibrate the ESC to transmitter on the Arrma 3s range; big rock, typhon, granite and senton. It is also the same calibration process on the 6s BLX185 ESC.

[@Max_1744]

Thank you so much, now my Big Bock is working again

[@midnightrcclub9046]

Thank you . Your video helped

[@jamesmolesson9991]

Simple and easy.. thanks!!

[@RoostedFilms]

Outstanding cheers mate

[@customrcupgrades2116]

Good video buddyn

[@azlierodolpo796]

Very helpfull.. tq🙏🙏🙏

[@ryanbautista885]

my typhon will just move an inch and it stops then a red blinking light is flashing on the esc, this goes for the reverse as well. But the steering is working fine.

[@janb.3198]

Same problem here but with the infraction 3s
Will drive for a minute and than stops and starts blinking red
Did you find the problem yet?

[@jaymestheboy4413]

I having the same problem. Did you guys ever figure it out?

[@jaymestheboy4413]

@@janb.3198did you ever figure it out? I have the same problem

[@wildcard3943]

Could be the lvc try setting it to nimh battery (disables it) and see if that solves your problem but you will be responsible for not over discharging your lipos as it will not automatically shut down

[@riffraff9070]

Thank you!

[@Imephone]

Thank you very much

[@simonpatchfield1092]

Thank you

[@mrtrex8438]

I was turning my rc on wrong and it broke so now I'm getting it repaired

[@matthewb7049]

thank you

[@zoecook7343]

Hasnt worked my sons car is making a weird noise when i press forward not moving though, anyone and ideas please

[@MicromittenHunter]

My arrma outcast 4s is having an issue with jittery throttle input. Barely wants to go. I’ve tried to re calibrate and it won’t let me go passed neutral. If I try do do full throttle and hit the button or reverse it doesn’t beep

[@am3r376]

does this mean everything will go back to factory settings when first start buying it & can play as usual without teasing other button presses? is that what you mean? Sorry i’m new in rc, my car is arrma typhon 3s

[@spudskirc4458]

It won’t go back to factory settings however it will ensure the transmitter is calibrated properly to the ESC.

[@Cribbie_]

I just put brand new Esc in and it won’t let me get past the neutral set point, blinks green once for neutral. But then it doesn’t blink for forwards and reverse

[@spudskirc4458]

Hi, is the radio set bound and esc plugged into channel 2? Does the steering work?

[@Cribbie_]

@@spudskirc4458 Hey thanks for the reply… Silly me had them in the wrong channels. The beast is alive now!!!!

[@brianu33]

I turned on my Typhon 3s and the brakes are stuck. I hit throttle it goes and brakes immediately. I tried recalibrating. No clue what to do, any thoughts?

[@spudskirc4458]

That’s an unusual one. Can you push the car on the ground freely?

[@brianu33]

@@spudskirc4458 I removed motor and the one bearing was blown apart. Have you ever replaced motor bearings before ? Apparently it’s common on Arrma

[@lucianopaq1265]

What does this actually help with ?

[@spudskirc4458]

Allows you to calibrate the esc to transmitter so you’re informing the ESC where neutral, full throttle and reverse is.

[@brianTwwjd]

Where's the receiver? How do yo bind it?

[@spudskirc4458]

The receivers under the esc you need to unscrew the 2 screws on the esc and the receiver box lid will open. Is it the stock radio you have?

[@samuellima1195]

My esc isn’t turning on

[@samuellima1195]

And my esc controller status led light BLINKS red, it doesn’t stay on red

[@spudskirc4458]

Hi, at first you said it doesn’t turn on and then said it blinks red, does it power then? Do you have any steering?

[@samuellima1195]

Spudski RC sorry, it’s kinda complicated, sometimes when I turn on my esc the status light doesn’t blink or shine red. But sometimes it does, the esc isn’t connected to the truck yet, this is because whenever I tried the process you showed in this video, the blinking lights on the truck weren’t blinking in the right pattern (blinking red when turned on, then blinks green once w/ esc on neutral and same with full throttle and full brake). Just lmk if you have any advice thanks 🙏

[@dirtbieks]

My reverse doesn’t work now

[@spudskirc4458]

You can enable and disable the reverse via the set button also so may have done this accidentally.

[@dirtbieks]

@@spudskirc4458 yeah I figured it out, the beeping on the set button didn’t work so I just had to guess lol

[@jpiijpii2358]

My car only beeps into neutral doesn’t do the other beeps

[@spudskirc4458]

Check throttle trim is centred, throttle limit is on 100 and reverse switch is on normal.

[@jpiijpii2358]

@@spudskirc4458 I have steering just no throttle

[@RC10GT]

Thank you