OEM Door Lights Installed! 2022+ Tundra/Sequoia 3rd Gen
Vložit
- čas přidán 15. 07. 2024
- OEM upper model Toyota Tundra LED door illumination parts installed successfully into our limited 2022 tundra! I hope this helps you to install your own lights in your tundra! It was really hard getting all of these part numbers together, so if this helps you please let me know in the comments! Here are all the part numbers for a CrewMax Cab 3rd Gen Tundra or 2023+ Toyota Sequoia:
Driver Front:
Trim Light: 810800C200
Tray Light: 810800C040
Passenger Front:
Trim Light: 810800C030
Tray Light: 810800C040
Driver Rear:
Trim Light: 810800C220
Tray Light: 810800C050
Passenger Rear:
Trim Light: 810800C210
Tray Light: 810800C050
Dash Lights (Not Installed in Video, and not confirmed fitment):
Light strip: 810800C190
Light "controller" ?: 810800C160
** small note on install for rear doors ** - We didn't record the rear doors but install was practically the same for the front and very easy. We did have to trim one of the plastic tabs on the new trim light to get it to fit but was very self explanatory and ensured proper fitment. If you have any questions on wiring or on the installation, don't hesitate to reach out.
Wiring Pins: a.co/d/4IPuVgi
Wire Used (20 G) : a.co/d/1jbFSig
Door Retainer Clips: a.co/d/0cWoVVJ - Auta a dopravní prostředky
Good vid for someone like me who is experienced. If you are looking to draw in the inexperienced, I would recommend having someone film you doing the work from start to finish.
Good job on recommending having replacement clips on hand. Most probably don't realize how easy it is to break plastic clips of all kinds. Also, thanks for linking to those wiring pins. Made the watch worth it for me as I keep forgetting to search for them and buy some.
Hey that is some great advice thank you. I’m so glad that you got something out of it! Thanks so much for watching
The example in the video suggests on the front passenger side #8 red for positive and #1 for ground but based on the wiring diagram the below is correct. I initially tried on my 22 limited with red and gray and it was constantly powered on even when lights switched to off. Pinning like the below will also allow dimming with the factory button for all ambient lighting.
Front driver
L6 Harness - black one
#3 Green = positive
#13 light blue = negative
Front passenger
K6 Harness - black one
#3 Light Green = positive
#1 Gray = negative
Rear driver
X4 Harness - black one
#3 Green = positive
#1 Light Green = negative
Rear passenger
W4 Harness - black one
#3 Green = positive
#1 Light Green = negative
Thank you so much for the info!! Mind if I copy and put this in the video description?
Please do!
@@maxxmayeux by any chance you have the wiring diagrams for the passenger doors for 2023 Sequoia Limited? The colors are different completely, and it is a J1 harness I think. The front doors worked well! Thanks.
Thank you for the video. Saved it for future use
Thanks for the walkthrough. Parts ordered!
Glad I could help! Thanks for watching
@@wolfpackmedia805so I got the passenger side door wired in just the way you showed but the lights stay on after head lights and all other illuminated panels shut off. It’s much dimmer but still on. Any suggestions?
Wow that was good !!
Great video. Would love to install this on my Limited as well! Thank you for your time putting this together. Could you edit to include the part for those clips you used in trim piece above the window.
So sorry I forgot to put that link in! Here you go. Thanks for watching! It’s on Amazon: a.co/d/0cWoVVJ
Great video! I had been wondering how to illuminate my limited door trims, and alas this video pops up. My question is, are all the parts available at the dealership or where did you purchase them?
Nice video! Thanks for sharing. I added up all the part numbers total cost and it was $448. Am I missing something or is there something we don't need on the list?
Can you please do a video on how to install the dashboard lights.
I want to do this as well as the dash and floorboard lights in my Pro.
I want to know if this comes with the wiring or do I have to order aftermarket wires
Great tutorial! Question can the install be done with just the trim light or are both needed
Great question! To make it easier on yourself yes you need both. The tray light comes with the wiring and clips you need to install the trim light. You could do the wiring yourself without the clip but I think that would be very tricky.
Did you by chance put lights in your foot wells, trying to pin down those part numbers as well
I went to order these and it was all either back ordered or very limited stock, in fact I believe the rear door was not even available, wonder when they will be in stock again?
Greetings, originally what combination did you use on the driver's door, mine is a 2022 trd pro, it has 8 pins
Great video! What’s the difference between the 040 vs 050 light harness?
I believe it was length of the wiring. I think the rear was the longer one? Thanks for watching!
Hey man great video! I have all the parts on the way and will install after the holidays. Do you happen to know where I can find the screws you mentioned to keep the trim light secure at 4:46? I too am running subwoofers and don't want any (more) rattles
I totally understand. The Tundra has enough rattles. I was unable to get the part number for those screws. I ended up just going to my local hardware store and grabbing the closest thing. I’m so sorry I don’t remember what size I grabbed. If you end up grabbing some please let me know! Glad u are giving it a go!
Thanks for the response man. I'll do some digging and get back to you.
Btw, fellow 805er here, glad to see a local on here!
Wonder if you could buy the replacement wire harness to save from splicing the wires.
Looked into this, and it looked to me like it was an entirely new loom which was very pricy. Definitely an option though if you have the time and money!
What size were the extra screws to secure the lightbar at the top of the doors?
Where did you buy the lights? Your truck looks good with them
The part numbers are in the description and I ordered them from my local Toyota dealer! Thanks for watching!
Great video! What was your approximate cost for parts?
Also I’m a former 805er as well. Still kept the phone number and miss it everyday.
Love it! It was about 200$
Should probably save our money for the rental car needed after our tundras go in for 3 weeks for the recall about to happen on debris in engine compartments 😢
Where can I get them?
All back order for at least 6 months
I have a 2023 Platinum with these accent lights installed at the factory. The light on the front passenger door has a darker (dimmer?) area centered about 6" from the rear part of the light. It's about 3-4" wide. I've had it to the Toyota dealer twice now trying to fix it with no luck so far. They replaced the light assembly and that didn't work. When I took it back, they said they did some kind of "adjustment" to it, and it was slightly better, but it's still got the dim area. I paid $75K for this truck, so I expect that these lights should look like yours do. Any ideas on how I can fix this myself?
I actually had this same issue on first install but didn’t notice it till later. The dimmer area is in the exact same spot. I opened up the door again and twisted/repositioned the light just a tad. I also added a small bit of foam on the top of the light (right where it was dim) to push the light closer to the gap in the trim where the light comes out. Once I put the door back together it looks way better. Not perfect but better. I think the part itself might have a defect from factory? I really appreciate you commenting on this though. If I hear of anyone else having this issue I will do another video about it.
@@wolfpackmedia805 Were you able to look at the light before installing the top "armrest" piece to see if the blue light was dim in that area?
The tray light is installed upside down. Also why didn’t you just use the unused female adapter to splice and connect to the window control?
bro had the dome light on and took away the whole experience of what the light looks like at night
It needs a plug and play version
@6:20 - can you share the positive and negative colors for the each door?
I will pop the cover off when I get home but it should be the same location and polarity for each door
Thanks!!!
Specifically looks for the driver - pretty sure that’s the only different one.
Did anyone every find that? I got the passenger but driver is different!
I was here first.
Too much effort…. Can I just pay you to put it in?
Loose the background music. Nice vid though thx
Any chance that this works on the 2023 SR5?
Good question! I also have an SR5
Did you ever find out if it works on the SR5? Would love to add it on mine
@@Mogcruiser
Check your window buttons. If they light up along with your headlights, you can tap into them as a power source.
@@VietLe-USAmy window buttons sure do light up when headlights are turned on. I wish he had more step by step details on the way he spliced the wires.
@@MogcruiserI’m trying to do this with my sr5 too. Wonder if it works