Fake Projects reveal | Increase charging current TP4056

Sdílet
Vložit
  • čas přidán 4. 04. 2022
  • #inverter #TP4056 #charging
    #awesometech
    #diy
    #diyhacks
    #diycrafts
    #tp4056
    #quantum_tech
    #fake
    #diyfakehacks
    Genuine video link :
    • Increase charging curr...
  • Věda a technologie

Komentáře • 32

  • @BertoldVdb
    @BertoldVdb Před 8 měsíci +3

    Connecting a bipolar transistor to the output can certainly increase the current, but the max charge voltage will become slightly lower (Vbe drop). You connected the mosfet wrong, it will just pass the input voltage to the output.

  • @gregjones3660
    @gregjones3660 Před 9 měsíci +1

    You could just solder that wire from the + of the input to the + of the output. no need for the transistor and additional circuitry. The mod will also be 5.15V where the current is limited by the power supply you chose.

  • @fu1r4
    @fu1r4 Před rokem +1

    It is the current that will get higher and not the voltage ...
    Connect a cell and use a clamp ammeter to measure amp

  • @leopoldofernandezjr.508
    @leopoldofernandezjr.508 Před rokem +4

    I watched this on another CZcams channel. Now i know it's Fake. But you must try first to remove our doubts regarding the project.

    • @Sams-Fy
      @Sams-Fy Před 9 měsíci +1

      It's the current (Amps) that increases, not the Voltage....

  • @riepriatna804
    @riepriatna804 Před 6 dny

    wrong resistor, it should be 1 ohm not 1 k, and this method is a current (A) boost, not a voltage (V) boost

  • @WalllOfNothing
    @WalllOfNothing Před rokem +1

    Why is the red probe(Positive probe) is connect to negative output?You put the red probe in the negative in your multimeter or what?

  • @Imbaloogs
    @Imbaloogs Před 6 měsíci +1

    Wrong way of testing... you are checking the voltage and not the current.

  • @mr.rishideshmukh2061
    @mr.rishideshmukh2061 Před 2 lety +1

    NYC

  • @albarbro
    @albarbro Před 6 měsíci

    i just replace the resistor using Zener Diode with 2pcs IRF9540 + 1pcs TP4056 + 5V 40A power supply to charging 4pcs 18650 = 7A MAX

  • @MiuiThemeIzan
    @MiuiThemeIzan Před měsícem

    Forma incorrecta de realizar la prueba... estás comprobando el voltaje y no la corriente.

  • @qanikadriu7232
    @qanikadriu7232 Před 9 měsíci +1

    Mos besoni këto gënjeshtra të mëdha,mos humbni kohën kot me këto gjëra.

  • @user-tz3qv9kz6r
    @user-tz3qv9kz6r Před 9 měsíci

    Does the charger not get hotter ?

  • @fu1r4
    @fu1r4 Před rokem +1

    👎 because you still have the protection film on your multi meter ...

  • @wahid6497
    @wahid6497 Před rokem +1

    just connect a battery or load then you will see the voltage will no go over 4.2 volts
    multimeter/voltmeter is not load

    • @wahid6497
      @wahid6497 Před rokem +1

      and if you are curius just put diode in series

    • @QuantumTechpakistan
      @QuantumTechpakistan  Před rokem +1

      brother you have to understand that lithuim ion cell needs constant voltage if we charge those lithuim ion cell with non constant voltage cells life decreases accordingly

    • @QuantumTechpakistan
      @QuantumTechpakistan  Před rokem

      encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcRbHK6OGTHo9I2wJOZCshE996-cQcgxwtpvjg&usqp=CAU
      Please understand this chart
      Link above

    • @wahid6497
      @wahid6497 Před rokem +1

      @@QuantumTechpakistan thank for the information but maybe see the voltage measurement while charging a battery cause you did just without connecting any battery i don't have the MOSFET on hand

    • @wahid6497
      @wahid6497 Před rokem

      If there is constant voltage

  • @ahsanhabibnafi2388
    @ahsanhabibnafi2388 Před 2 lety +1

    Whats that rasistor?