WPL C44KM TOYOTA Landcruiser FJ45 With Best Sound & Light Controller: Quick Demo!
Vložit
- čas přidán 28. 08. 2024
- In this video: the awesome WPL C44KM Toyota Landcruiser FJ45 with metal axles and gears & DIY Arduino electronics!
- Test drive on steep incline, demonstrating virtual clutch , sound & lights
- 3D printed scale rear lights
- WPL 2 speed transmission with metal gears
- How to order pre assembled PCB for RC sound & light controller
- Detail pictures (SMD LED, ESP32 sound & light controller, paint works etc. wooden maple syrup box for electronics
Your supplier for the pre assembled Open Source Sound & Light Controller: www.pcbway.com/
Official WPL store (affiliate link will support the channel): www.wpl-rc.com...
Sound Controller:
Virtual 3 speed transmission: • WPL B36 URAL-375D With...
Flysky support: • The Best Engine Sound ...
Revving sound, Kennwort sounds: • ESP32 Arduino RC sound...
SCANIA V8 Open Pipe: • Worlds Most Realistic ...
Light & sound controller features:
- Sampling rate up to 22’050Hz, instead of 16’000
- Multiple sounds can play simultaneously
- real DAC outputs, no R/C filter circuit required
- the variable speed engine sound can play at the same time as an additional sound with fixed speed (a horn or a siren for example)
- A lot of pre configured vehicles are available
- special sounds included like: „Martinshorn“ fire truck horn, US Police siren, Swiss post bus horn, train horn, car horn, MAN TGA truck horn
- Engine sounds for: Land Rover Defender V8, ford Mustang, Chevy Nova, Dodge Challenger, MG B GT V8, LaFerrari, Scania V8, Ural V8, Kenworth, CAT, Detroit Diesel etc.
- Air brake & jake brake sounds
- Output for vibrating motor, which simulates engine vibrations
- Vehicle inertia simulation (if crawler type ESC is connected to pin 33)
- Virtual clutch, making the engine sound much more realistic (if crawler type ESC is connected to pin 33)
- simulated manual 3 speed, automatic & double clutch transmissions
- The TAMIYA 3 speed transmission is synchronised in software and can be shifted while driving
- Many light functions like headlight, tale light, brake light, indicators, blue light, foglight, sidelights, high & low beam
- 6 PWM RC servo signal inputs
- 13 light outputs
- PWM, PPM, IBUS & SBUS communication, makes it compatible with most common remotes
- The pre assembled SMD PCB can easily be ordered according to: github.com/The...
Material links for sound controller:
- PCB including SMD components assembling: www.pcbway.com/
- ESP32 board: www.banggood.c...
- PAM8403 amplifier: www.banggood.c...
- Speaker: www.banggood.c...
My DIY Open Source Arduino Stuff:
github.com/The...
github.com/The...
github.com/The...
www.thingivers...
github.com/The...
Check out my other RC videos: • Remote control
My GitHub: github.com/The...
My Thingiverse: www.thingivers...
Follow me on Twitter: / thediyguy999
on Flickr: www.flickr.com...
and on Instagram: / thediyguy999
If you want to support this channel:
/ thediyguy999
paypal.me/thed...
#TheDIYGuy999 #WPL #ESP32
Very very awesome 👍👍👍
cool rc and nice light and sound demo
Thanks
Hi, it looks amazing! What ESC is used for C34? Is the HobbyWing 1080 only supported by the sound controller?
It is a Hobbywing 1060. Every "crawler style" ESC (with proportional brake) is supported, but the 1080 is the best in my opinion.
Looks and sounds great. I like how you made the tail lights with the SMD leds. FYI I tried using a cheap little TDA2030A amplifier module which is about twice as loud as the PAM8403 in my tanks. I run it off my 2S lipo so it gets a little more voltage.
Thanks. This amp is an analogue type and will use a lot of current. For bigger models it may make sense.
Great DIY!
Thank you!
Hallo Martin,
Wie immer großes Kino
Schöne Grüße Andreas
(MAN Tgx)
Danke, Andreas. Gegenüber dem Video konnte ich das Anfahrverhalten des Hobbywing 1060 nochmals verbessern. In der nächsten Version werden erweiterte Einstellparameter für den ESC vorhanden sein. Gruss
@@TheDIYGuy999 Also funktioniert jetzt auch der 1060 und nicht nur der 1080 ? Perfekt
@@picturexxxx Ja, der funktioniert auch. Allerdings ist der 1080 nach wie vor besser, da man ihn mittels Programmierkarte optimal einstellen kann. Ich umgehe das soweit möglich, indem ich das Ausgangssignal vom ESP32 soweit möglich beeinflusse.
@@TheDIYGuy999okay da bin ich raus.
@@picturexxxx Wieso? Es ist alles wie gehabt, aber zusätzlich kannst du beim Anfahren etwas mehr ESC Power geben, falls die "Kupplung" zu stark schleift. Ebenso kannst du den Rückwärtsgang schneller machen. Einstellbar ab der nächsten Version im Tab "3_adjustmentsESC.h"
Very nice. Though I wish you’d return to smaller scale RC cars ;)
Thanks. I prefer bigger vehicles, my eyes don't get better...
Sadly...
Hello, getting a PCB built at JLC some parts are not in the libuary/stock. I have found very similar parts for R27 and R30 200ohms BUT R28 shows 47ohms on the schematic,can not find anything similar to choose,can you advice please? will 200ohms bo ok also,like R27 and 29?
I don't use them, but they have a 47Ohm SMD resistor for sure. You can use 200 ohms, but the LED will be a lot darker
Hello, I have a question about your sound and light module. Using PCBWAY and your gerber files, it states 10 unique parts and 24 parts jn total. I can get a cheaper deal on JLCPCB their site does not show part amount in samw way But counting the parts listed only 23 parts are used. I used same BOM and CPL files. Do you have any views on this please. Thanks
Just order the boards as described in the PDF. If you want to use a different supplier, you have to edit the components list by yourself.
Hi, nice to meet you, can you help me, I am using the latest RC Sound Endine ver 6.4 and communication using PWM, but when pin 33 is connected to the ESC, the motor does not rotate, only sound comes out.Why is that? Can you help me? Looking forward for your help,thank before🙏
Hi, hard to tell. Are you using a pre made board? What type is your ESC? You should do basic error solving steps, using a multimeter or oscilloscope. Also check for bad solder joints.
Any way to hear the program sound files before deciding which to use in an upload?
I asked in the forum but no answer.
No, just upload the vehicle and test it on the controller
Awesome 👍👍
Thanks
@@TheDIYGuy999 sir can i ask how can message you i need to ask something
@@fuxionlab3704 Ask your question here
@@TheDIYGuy999 how can i use the code with only potentiometer i want to use the idle and rev only
@@TheDIYGuy999 how can i use this code with out RC controller i want to use a button for rev and potentiometer for running the motor
Hello,i made a big mistake with my question below. I got the SMD wrongs. Using the BOM all the parts match except 1. JLC want to use 200ohms 1/8w R for part R9. The schematic shows 330ohms for that part???? Should i override JLC and choose 330 for R9? i do not know jlc wants to use 200ohms ,when it auto chooses 330 for R1,2,3,4,5,6,7,8 and 10. Sorry to keep asking but i am a novice
Hi, I assume you are talking about the sad version? If yes, the schematic says 200Ohms for R9.
github.com/TheDIYGuy999/Rc_Engine_Sound_ESP32/blob/master/Eagle_PCB/SMD/RC_Engine_Sound_ESP32.pdf
@@TheDIYGuy999 On your "final" version what should R9 be?
@@garymurphy5133 This is not the SMD version, don't mix them up. It is 330 Ohms
@@TheDIYGuy999 Sorry my mistake,got a bit confused with both types. The schematic i found is not for the "latest" board? will chosse the 330 ohms