Why didn't you get 2 tweeters and 2 midrange speakers with the sub? I will build a similar speaker, so i'm trying to figure out all my options first. Nice vid keep up the work!
Do you sell this speaker system? Where do i find these systems already built and ready for purchase. I've been looking for a portable Bluetooth 2.1 boombox forever!
Wonderful glad youtube showed my your channel subscribed it. Looking forward to building these. Also if you can have a video of it playing out in open air like garden or terrace wanted to know how it performs especially vs boss or jbl type BoomBox. Also since this is on battery would like to take in different cars that don’t have a good sound system
Such a nice build. I want to build similar setup but with 2 DSPB-250 and 1 KAB-100. Want to power 2 woofer with 1 board and 2 midrange and tweeters with the other board. Ofcourse the 100 watt amp to a subwoofer. What are your thoughts? Looking forward to your smaller formfactor build. Can the below frequencies be programmed to the board and make it all work seamlessly? Current drivers I am looking at :- From 10,000Hz - 22,000Hz HiVi B4N 4" Aluminum Round Frame Midbass - 2 Peerless by Tymphany BC25TG15-04 1" Silk Dome Tweeter - 2 Bass 35Hz - 3,000Hz Tang Band W6-1139SIF 6-1/2" Paper Cone Subwoofer Speaker - 1 Mid 3,000Hz - 10,000Hz Dayton Audio ND105-4 4" Aluminum Cone Midbass Neo Driver
Hey, have you made a portable subwoofer? I'm looking to make one that fits into a Pelican Air case, as well as an 8 or 10" top speaker for taking my DJ setups to destinations that require flying.
Does this equipment setup allow for expanding the playtime with more batteries? Or does the current equipment not allow for easy expansion of additional power cells?
The current battery board is limited to five 26650 cells, but you could theoretically put to separate boards in parallel to the amplifier to double the capacity. But as is this 18.5v 5ah battery gives plenty of playtime on its own.
How much was approximate cost? Do you have your plans? Did you build crossovers? I want to build one with a Tang Band 6.5inch. let me know if you make one. Nice work
Hey thanks! This speaker cost roughly $450 to build. I have technical drawings of the cabinet that I will post on my website once I have a finalized design and I know everything fits. The crossover for the sub and full range drivers is done digitally through the DSP, so there are no passive crossover components. Make sure you're subscribed so you get the notification when I upload a video, thanks for watching!
Very nice speaker!
Yo waited for a while keep it up ma man
Why didn't you get 2 tweeters and 2 midrange speakers with the sub? I will build a similar speaker, so i'm trying to figure out all my options first. Nice vid keep up the work!
I just need a list of components to buy to build an ac powered , Bluetooth radio with a subwoofer but I'm having a hard time finding it
sweet bbox, looking forward for a smaller one :)
Do you sell this speaker system? Where do i find these systems already built and ready for purchase. I've been looking for a portable Bluetooth 2.1 boombox forever!
Wonderful glad youtube showed my your channel subscribed it. Looking forward to building these. Also if you can have a video of it playing out in open air like garden or terrace wanted to know how it performs especially vs boss or jbl type BoomBox.
Also since this is on battery would like to take in different cars that don’t have a good sound system
Fantastic.....
what a beauty
Hi any chance you can upload a photo showing how to connect the 2 dayton boards.
Can you make build logs of your speakers?
Are there stronger amplifiers that can push around 100rms to a sub?
List of all parts and steps would be appreciated I'm in UK so recommendations by others is welcome also
Such a nice build. I want to build similar setup but with 2 DSPB-250 and 1 KAB-100. Want to power 2 woofer with 1 board and 2 midrange and tweeters with the other board. Ofcourse the 100 watt amp to a subwoofer. What are your thoughts? Looking forward to your smaller formfactor build.
Can the below frequencies be programmed to the board and make it all work seamlessly?
Current drivers I am looking at :-
From 10,000Hz - 22,000Hz
HiVi B4N 4" Aluminum Round Frame Midbass - 2
Peerless by Tymphany BC25TG15-04 1" Silk Dome Tweeter - 2
Bass 35Hz - 3,000Hz
Tang Band W6-1139SIF 6-1/2" Paper Cone Subwoofer Speaker - 1
Mid 3,000Hz - 10,000Hz
Dayton Audio ND105-4 4" Aluminum Cone Midbass Neo Driver
Now eiffelton audio have nice 4.1 amplifier whith dsp and tpa3116 and ldac bluetooth.
How'd the smaller version build go?
Nice
Pecka super sound Blaster
Woh wide and how long is the wood cut?
Hey, have you made a portable subwoofer? I'm looking to make one that fits into a Pelican Air case, as well as an 8 or 10" top speaker for taking my DJ setups to destinations that require flying.
Does this equipment setup allow for expanding the playtime with more batteries? Or does the current equipment not allow for easy expansion of additional power cells?
The current battery board is limited to five 26650 cells, but you could theoretically put to separate boards in parallel to the amplifier to double the capacity. But as is this 18.5v 5ah battery gives plenty of playtime on its own.
I do think it's sounds dynamic in highs. Dude you lacking tweeters in this thing to be able to create true dynamic highs or real wide soundstage.
I own a cabinet shop if you need something Cnc cut let me know. I would love to experiment with cabinet designs.
How much was approximate cost? Do you have your plans? Did you build crossovers? I want to build one with a Tang Band 6.5inch. let me know if you make one. Nice work
Hey thanks! This speaker cost roughly $450 to build. I have technical drawings of the cabinet that I will post on my website once I have a finalized design and I know everything fits. The crossover for the sub and full range drivers is done digitally through the DSP, so there are no passive crossover components. Make sure you're subscribed so you get the notification when I upload a video, thanks for watching!
Links???
Where can I get this
I'd buy one.
Watt?
It's about 100 watts RMS total, 2x25 for the full range drivers and 1x50 for the subwoofer
Please make me one of these.
🙏🥺😢🙏
I wanna buy one.
I am a noobie.
I can't make one my self.
😵💫😖😣