Massive thanks to Pawel Spychalski and Painless360, without whose YT tutorials, I wouldn't have been able to get through this. czcams.com/channels/mX3OXToMBKTppgRskDzpsw.html czcams.com/channels/p1vASX-fg959vRc1xowqpw.html
At about 4:00 you select the receiver type on the Configuration page The new iNav has moved the receiver selection to the transmitter page I spent three days resoldering / googling / flashing the firmware, etc trying to figure out what I did wrong, to cause the receiver selection to not show Turns out the developers just moved it Hope this saves someone else some time!
Joshua thank you for creating this video! This helped me resolve an issue I had with arming that I had been trying to figure out for two days!!! Thank you !!!
I been struggling to get my drone off the Ground compared to Open Pilot this was part of my mistake " I learnt something " i'll keep watching to the end Thanks Joshua !
Joshua I have new 2.5 inav and in configutation tab I don see Receiver mode where I can choise my sbus receiver. My xm+ is binded corectly, serial port is ok and I can see the movements in Receiver tab. I think this receiver mode is in Receiver tab now in new inav2.5
1:35 - Sounds like someone needs a shirt catalog! OR Someone: "Why Joshua do you have 14 of the same T-Shirts?" Joshua: "Weeeell when you are a YT celebrity, it just makes sense and is more efficient."
Hi i want to build a heavy lifter but when it's in the air and accidently i push the throttle to 0 i don't want him to fall from the sky . what should i do ? And for landing it's the same question i don't want him to fall if i push the stick down to loose altitude.
@@JoshuaBardwell I swear I was flying in your house on liftoff and I saw a yt notification from ‘ Joshua Bardwell ‘ Thx a lot for your videos and your response 👍🏻👍🏻👍🏻👌
Hi bro following the INAV build I am running INAVE 2.6.0 on Mac .when i’m going into configurations tab I can’t find serial receiver configurator I’m using a NOXE F4 flight bored
Why do you think that setting the endpoints on the transmitter is better? The CLI commands seemed much simpler to me, when I've set them via the transmitter in the past I always found that the number competed and it was hard to get it exact. I presume that the channel range command doesn't take into account the previous range, so if you want to reset the ranges (Maybe if you buy a new transmitter) you would need to reset them to 1000 / 2000 before reading the new values from the receiver tab?
I am also wondering. Rxrange seems easier. I always set the endpoint in my TX. In the old days you had to set everything in the TX, like curves, mixes, etc. A lot of the configs moved to the FC, the TX became dumb again. So why not the endpoints as well.
Setting endpoints on the transmitter keeps maximum resolution. In addition, once you've set it then it is the same for all future quads bound to the same model, so as long as you're using the same receiver type, you never have to do it again.
FLyR9ツ lol. I was thinking the same thing, but Nurk dropped a video yesterday of him using RTH on Betaflight. I have been INaV for the possibilities lol
Joshua Bardwell , ok Joshua, so this is basically to tell inav which are the end points of your particular radio. But when setting up a new model and ensuring servos are at 90 degrees, is it ok to fine tune servos with radio end points? Then do this radio end point on inav?
Joshua, if im using an older frsky receiver in D8 mode that has ppm capability am I still going to select Ibus for the uart reciever connection - I didn't see the ppm option in your video?
Hi, I tried to use INAV but my OSD doesn't work correct. I tried INAV because I wanted to use GPS but now I am using Betaflight. Maybe you will have the same problem with your OSD and you will have a solution. For this problem.
Hi Joshua Bardwell can you do a 1 on 1 with me because I ordered my first drone which was a eachine wizard and I was wondering if you could help me get it all setup. I have Been watching your videos for years and that’s how I got the inspiration of buying my own race drone I started with the eachine wizard X220 and then I got an Emax Tiny hawk and then Emax Tinyhawk freestyle and those quads work but in the receiver tab of beta flight none of my switches work for my x220 and I was hoping if you could help me please read this
Quad definetly does not feel as good in acro mode with my Betaflight PIDs (Website says iNAV and BF PIDs are the same). Could be because Betaflight is optimized for stable and fast acro flying. Could be my Filter settings. Betaflight with stock PIDs handles way better than iNav imho.
hello Joshua...sorry for off topic coment...I am from eu and love to watch your live streams,but cant watch monday strem becouse time zone etc...on y.t your monday stream is private and I cant watch it...can you help?...thank you
Massive thanks to Pawel Spychalski and Painless360, without whose YT tutorials, I wouldn't have been able to get through this.
czcams.com/channels/mX3OXToMBKTppgRskDzpsw.html
czcams.com/channels/p1vASX-fg959vRc1xowqpw.html
Started watching your videos three years ago to learn how to build. I can't thank you enough for helping the community the way that you do.
At about 4:00 you select the receiver type on the Configuration page
The new iNav has moved the receiver selection to the transmitter page
I spent three days resoldering / googling / flashing the firmware, etc trying to figure out what I did wrong, to cause the receiver selection to not show
Turns out the developers just moved it
Hope this saves someone else some time!
haaa I had this same problem.... :P....receiver mode is moved now
We’re having fun now!
Joshua thank you for creating this video! This helped me resolve an issue I had with arming that I had been trying to figure out for two days!!! Thank you !!!
I been struggling to get my drone off the Ground compared to Open Pilot this was part of my mistake " I learnt something " i'll keep watching to the end Thanks Joshua !
I think my GPS is stuck in customs 🛃😂
Thanks for the iNav series Joshua.
Your the Man straight up 💪
Hi Joshua, nice to see you dive into iNav. It shows it is getting adult by you reviewing it.
please make a pizza drone.
BEEN watching you for a while and love your videos I’m building a fpv drone with my earnings as a 15 year old
I know it is not for this video, but why is Monday's Q&A is marked private
NDA violation? :)
It's public now.
not picking up my receiver.. and only 1 motor spins.. i picked flywoo411
Could you do a tuning vid for complete beginners? I’ve seen others and am usually lost.
Joshua I have new 2.5 inav and in configutation tab I don see Receiver mode where I can choise my sbus receiver.
My xm+ is binded corectly, serial port is ok and I can see the movements in Receiver tab.
I think this receiver mode is in Receiver tab now in new inav2.5
1:35 - Sounds like someone needs a shirt catalog!
OR
Someone: "Why Joshua do you have 14 of the same T-Shirts?"
Joshua: "Weeeell when you are a YT celebrity, it just makes sense and is more efficient."
Hi i want to build a heavy lifter but when it's in the air and accidently i push the throttle to 0 i don't want him to fall from the sky . what should i do ?
And for landing it's the same question i don't want him to fall if i push the stick down to loose altitude.
Enable air mode in Betaflight.
@@JoshuaBardwell I swear I was flying in your house on liftoff and I saw a yt notification from ‘ Joshua Bardwell ‘
Thx a lot for your videos and your response 👍🏻👍🏻👍🏻👌
Joshua does also applies to inav fixed wings?
Hi bro following the INAV build I am running INAVE 2.6.0 on Mac .when i’m going into configurations tab I can’t find serial receiver configurator I’m using a NOXE F4 flight bored
Why do you think that setting the endpoints on the transmitter is better? The CLI commands seemed much simpler to me, when I've set them via the transmitter in the past I always found that the number competed and it was hard to get it exact.
I presume that the channel range command doesn't take into account the previous range, so if you want to reset the ranges (Maybe if you buy a new transmitter) you would need to reset them to 1000 / 2000 before reading the new values from the receiver tab?
I am also wondering. Rxrange seems easier. I always set the endpoint in my TX. In the old days you had to set everything in the TX, like curves, mixes, etc. A lot of the configs moved to the FC, the TX became dumb again. So why not the endpoints as well.
Setting endpoints on the transmitter keeps maximum resolution. In addition, once you've set it then it is the same for all future quads bound to the same model, so as long as you're using the same receiver type, you never have to do it again.
If this thing get RTL working at the end, u cant know how many peoples gonna make it.
FLyR9ツ lol. I was thinking the same thing, but Nurk dropped a video yesterday of him using RTH on Betaflight. I have been INaV for the possibilities lol
i dont have a "receiver mode" tab but my receiver on the drone has a green light. any help plz?
Joshua, this end point setup procedure also applies to inav fixed wing?
Yes
Joshua Bardwell , ok Joshua, so this is basically to tell inav which are the end points of your particular radio. But when setting up a new model and ensuring servos are at 90 degrees, is it ok to fine tune servos with radio end points? Then do this radio end point on inav?
ReversedPropDirection PLS! :)
@JoshuaBardwell Everyime I go to the configuration tab in iNav, I just get "waiting for data" endlessly
I would try to start narrowing it down. Is it just that FC? Is it the computer? Maybe reflash the FC.
Joshua, if im using an older frsky receiver in D8 mode that has ppm capability am I still going to select Ibus for the uart reciever connection - I didn't see the ppm option in your video?
I would strongly recommend getting a serial receiver. I'm not sure this FC supports PPM input.
@joshuabardwell would love to see a monthly giveaway of the Tyro build... ? Its difficult to get my hands on the kit where I'm located..
Bad news: I just drop ship the giveaway items.
Tony Dean He buys it from Banggood and they ship it to you. If they can’t ship it to you, neither can he.
Включите субтитры для русского языка, а какая версия Айнав?
I just finished pt3 what timing
So endpoints settings just for sticks?
Or all chanels?
Just sticks.
@@JoshuaBardwell Thanks. Realy fast answer you are the best
Hi, I tried to use INAV but my OSD doesn't work correct.
I tried INAV because I wanted to use GPS but now I am using Betaflight. Maybe you will have the same problem with your OSD and you will have a solution. For this problem.
ReUpload the font.
czcams.com/video/3GDK02sOtsY/video.html
@@JoshuaBardwell thank you very helpful 👍. Now I have a new problem. When I fly my copter activated. But I still have connection with my receiver.
Hi Joshua Bardwell can you do a 1 on 1 with me because I ordered my first drone which was a eachine wizard and I was wondering if you could help me get it all setup. I have Been watching your videos for years and that’s how I got the inspiration of buying my own race drone I started with the eachine wizard X220 and then I got an Emax Tiny hawk and then Emax Tinyhawk freestyle and those quads work but in the receiver tab of beta flight none of my switches work for my x220 and I was hoping if you could help me please read this
Twitch MoonGless email him
Oh it’s ok I got it finally. My flight controller wasn’t saving but all of a sudden it wants to and I got all my switches set
how polished is iNav when compared to Betaflight?
Quad definetly does not feel as good in acro mode with my Betaflight PIDs (Website says iNAV and BF PIDs are the same). Could be because Betaflight is optimized for stable and fast acro flying. Could be my Filter settings. Betaflight with stock PIDs handles way better than iNav imho.
hello Joshua...sorry for off topic coment...I am from eu and love to watch your live streams,but cant watch monday strem becouse time zone etc...on y.t your monday stream is private and I cant watch it...can you help?...thank you
It's public now.
@@JoshuaBardwell already watching....thank you
first
This is becoming borderline clickbait.
I'm not sure what you mean. What part of the title or thumbnail is misleading?
@@JoshuaBardwell Sorry Mate, just frustated its taking so long to get to the end. Cant wait to hear you say lets go fly. Your doing a great job.
It will be finished by the end of next week.