Her First Pro Pedalboard
Vložit
- čas přidán 7. 08. 2024
- Today I'm building a pedalboard for one of my favorite Nashville-based Singer/Songwriter/Guitar-Gear-Enthusiast, Lindsay Ell!
After a year-long delay due to the pandemic, we were finally able to build a bullet-proof touring rig for the great Lindsay Ell. In this video, I'll walk you through my rig-building process, showing you the tips and tricks I used to build Lindsay's first PRO pedalboard.
TABLE OF CONTENTS:
00:00 Introduction
01:03 Holy Trinity of Tone
02:58 Layout
03:38 Power Cables
04:30 Audio Cables
05:40 Pedalboard Demo
13:17 Lindsay's Final Thoughts
13:55 Conclusion
Lindsay's DIY Interface Diagrams, Parts List, and Drill Template:
(Four Cable Method or WET DRY Buffer) - vertexeffects.com/diy-buffer-...
Follow Lindsay Ell
Instagram - / lindsayell
Facebook - / officiallindsayell
Website - www.lindsayell.com
⬇️ Private Tone Consulting from the Rig Dr. ⬇️
therigdr.com/collections/all/...
🔽 Buy our Pedals/Pedalboard Materials🔽
Zip Ties: www.therigdr.com/collections/...
Tie-down Mounts: www.therigdr.com/collections/...
Velcro: www.therigdr.com/collections/...
Pedalboard Patch Cables: www.therigdr.com/products/pat...
Instrument Cables: www.therigdr.com/products/gui...
Pedalboards: www.vertexeffects.com/store#!...
VERTEX Pedals: vertexeffects.com/store
⬇ DIY BUFFER INTERFACE DIAGRAMS, TEMPLATES, & MATERIALS ⬇
Mono - vertexeffects.com/diy-buffer-...
Mono w/Tuner Out - vertexeffects.com/diy-buffer-...
Mono w/Splitter - www.vertexeffects.com/diy-buf...
Mono w/Audition Loop - vertexeffects.com/diy-buffer-...
4 Cable Method (FX Loop) - vertexeffects.com/diy-buffer-...
Wet/Dry - vertexeffects.com/diy-buffer-...
Stereo - vertexeffects.com/diy-buffer-...
🔻 //rig consulting//🔻
therigdr.com/collections/all/...
🔈 //podcast//🔈
Apple: apple.co/36dSQzK
Spotify: spoti.fi/2WGLku8
⬇ RECOMMENDED MATERIALS ⬇
some urls below contain affiliate links
//buffers//
Vertex DIY Buffers - vertexeffects.com/diy-buffer
Mesa Boogie High-Wire (dual buffer) - bit.ly/2lZwS0s
TC Bonafide Buffer (x2 input + output) - amzn.to/2vrTSug
Truetone Buffer (x2 input + output) - amzn.to/2NLDA8l
Carl Martin Buff Deluxe - www.carlmartin.com/buff-de-luxe
//power supply//
CIOKS 7 - amzn.to/3d4qOty
CIOKS 8 - amzn.to/2zW5YOn
CIOKS 4 - amzn.to/33jWAOZ
Strymon Zuma - amzn.to/3dpZANe
Strymon Zuma R300 - amzn.to/2ZgLclt
Truetone CS6 - amzn.to/2wWLbII
Truetone CS7 - amzn.to/2x1Nf2k
Truetone CS12 - amzn.to/33rfLq3
Voodoo Lab Pedal Power 3 - amzn.to/3asqK6r
IEC Plug Covers - bit.ly/34fpGl3
//dc power cables//
2.1mm DC Power Plugs (right angle) - bit.ly/2pGqXzI
2.1mm DC Power Plugs (straight) - bit.ly/36wd1sA
Bulk Power Cables (pre made) - amzn.to/3ev1q0t
//midi//
MIDI Plugs (right angle) - bit.ly/2oKHDFG
MIDI Plugs (straight) - bit.ly/32fNNLF
MIDI Cable (bulk) - amzn.to/2tPAHWQ
//velcro//
Vertex Super Lock - therigdr.com/collections/all/...
//cable management//
Zip Ties - www.therigdr.com/products/zip...
Tie Down Mounts - www.therigdr.com/products/tie...
Tone Essentials Kit - www.therigdr.com/products/ton...
//pedalboard tools//
Soldering Iron - amzn.to/2TTdMI4
Solder (60/40) - amzn.to/2U7XhsD
Solder Dispenser - amzn.to/2GpgMpR
Octopus Arms - amzn.to/2V3O8OD
Wire Strippers (30-20 AWG) - amzn.to/2BBMI6n
Wire Strippers (20-10 AWG) - amzn.to/2EbhBR3
Wire Snips - amzn.to/2EazwqU
Vise - amzn.to/2E9eTLO
Heat Gun (embossing gun) - amzn.to/2BwGdlm
Label Maker - amzn.to/2BCBcHU
Label Maker Tape (black) - amzn.to/2Cd3CZe
Label Maker Tape (clear) - amzn.to/34piDD4
Deoxit D5 Contact Cleaner - amzn.to/2GEm4gu
Truetone Milliamp (mA) Reader - amzn.to/2F9v3VN
Tone Brush - amzn.to/2HIfze3
Upholstery Crow Bar - amzn.to/2HIOU0K
Multimeter - amzn.to/2YW9BdE
Goo Gone - amzn.to/31rGJeS
👇 // diy diagrams // 👇
DIY Power Cables: vertexeffects.com/diy-power-c...
DIY Interface: vertexeffects.com/diy-interface
DIY Buffers: vertexeffects.com/diy-buffer
#LindsayEll #RigDoctor #PedalboardBuild - Hudba
Not gonna lie... the only reason I clicked on the video in the first place was because of that pink Klon. But man she has a nice touch! Keep the vids coming Mason, you make pedalboards look like art pieces at a museum.
Pink Klon all day long!
Disagree! I clicked because of that beautiful woman.
Lindsey is a great player and a refreshing blast of constant positivity on social media.
Agreed!!!
Mason you HAVE TO track down video of Lindsey’s touring guitar player Austin Goodloe. He’s freaking fantastic. Great vid!
Will do…thanks for watching
Beautiful board! Mason’s work certainly has a distinct visual aesthetic that I appreciate.
Thanks for watching!
Really love your videos . Hope I can build my dream pedalbord one day . Might be impossible for now cuz I can't afford but not gonna give up . Thanks for the inspiration sir . Love Lindsay ell's pedalboard
Hang in there...it takes time and time will allow you to really curate what you love when you build your dream rig!
@@VertexEffectsInc Awwwww!! Thanks for replying. Mean a lot to me !! 🥺
Excellent video as always, i Really enjoy to watch, listen and learn from your vids, congrats!!!
🙏🙏🙏
Very informative. Answered questions I didn't know I had. Thank you guys
Our pleasure!
TABLE OF CONTENTS:
00:00 Introduction
01:03 Holy Trinity of Tone
02:58 Layout
03:38 Power Cables
04:30 Audio Cables
05:40 Pedalboard Demo
13:17 Lindsay's Final Thoughts
13:55 Conclusion
Lindsay's DIY Interface Diagrams, Parts List, and Drill Template:
vertexeffects.com/diy-buffer-4cm-wet-dry
Listen to Lindsay's Newest Release "Heart Theory"
lindsayell.lnk.to/hearttheory
07:25
@@javier_arenales Sweet spot?
@@VertexEffectsInc 😂
Ms. Lindsay Ell,
Fire you management company. I admit I am not big on country, but I didn't know about you until this video (thanks, Uncle Mason).
Terry D. Miller, MBA
She's great! Definiltey check out her music! I found out about here from the Continuum Project album and have been a fan ever since!
Nice neat job 👍 The Zuma is by far the best and quietest PS I’ve used, good call. Currently have mine mounted under the board with the Zuma brackets, to make room for more pedals on top when needed.
It's a good one, there are also others on par that we list in our description if you're wondering what we recommend.
That Micro Tron is somethin I have to check out. Also, heck of a rig Mason and Lindsay!
Thanks for watching!
That pink Centura is awesome. Love the micro tron too
The best!
Great board..Love her playing!!
She's great!
Great video Mason, thanks for sharing. I'm really impressed with those Ceriatone klones, I got one try as a boost at the end of my chain and it sounds that good that it is now just always on, I have to push the output knob with my foot to turn the boost up when required
Nice! Heck yea!
Great Episode Mason and Lindsay!!!
Thanks for watching!
amazing work as always guys ;)
Thank you so much 😀
Wow . . . on Tour since 10 years old - Thats Impressive. Talk about: honing-your-craft & knowing your true-calling in life. Those Lexicon Reverb's are just "Sick" (so mad I sold my Lexicon Rack). Nice board. oNe LovE from NYC
Yes indeed! RV-7 all day!
She is the Best for me! So talent 🎼🎸💜
Lindsay is great!
Lindsay Ell and a pedalboard, this was literally the video I needed lmao
Huh?
@@VertexEffectsInc as in this video made my day lol
I realy fan of you mr. Mason...
I work for build pedalboard too in music shop. Your tips and suggestion always become my inspiration.. cheers from indonesia 🇮🇩🇮🇩🇮🇩
Happy to hear that!
lindsay ell is amazing. i can definitely hear some john mayer influence in her playing and tone as well.
In part that’s the ultra phonic doing some work
@@UnleashDLion Or the fact that she is a huge fan of his and covered his entire Continuum album and put in a TON of work learning how John plays...
Certainly some JM influences for sure :)
Awesome job man!!
Thanks for the visit
Lindsay Ell and pedalboards. Awesome vid
Thanks for watching!
Great job
man that micro tron sounded sickkkk
Heck yes!!!
Awesome video! Just built my first proper board for about 2500CAD. Got a steel string supreme and you guys killed it. Yes it does the mayer thing but it also just has wicked tones in it.
I'm so pleased!
@@VertexEffectsInc Thank you again for making it, I am sure you hear it all the time but I have looking for years for pedals to give the sound I got when I clicked this thing on! Pair it with a strymon deco and fugghetaboutit. Not 1 million buttons and patches just plug it in and it works.
I switched to Strymon Zuma Power Supply from a Truetone CS6. I needed more ports because I have lots of pedals. Just my luck FED EX Lost my first one so I'll get another one from Sweetwater!!!! This board is going on 8 weeks to build...Uggggh!!!! Shortages of pedals to lost orders. Keep making videos Mason! I watch them all!
🙏🙏🙏
I actually got the idea to put my volume pedal in between my drives and modulation pedals from Lindsay's last pedalboard
Always a good place for a "master volume"
Groovy pedalboard!
🥰🥰
that is awesome! ✨✨✨✨✨
Glad you think so!
Your pedalboard builds are always so clean. It's like art.
Glad you like them!
I came for the Pink Klon
Yes!
love her. great player
The best!
im not even a pedal nut, my multi effect does me fine, but that was a great vid. very interesting
Glad you enjoyed it!
This is great, have you ever thought of making a that buffer system a product? I would totally buy it!
We're releasing a few versions shortly as production models, we also have our custom shop version available on www.therigdr.com
Sweet Dee can really jam
Lindsay is a great player!
Awesome build as usual, I really have learned a lot from your videos Mason, thank you. What kind of road case does it use? is it a stock size Pelican or something custom?
Pelican, SKB, Gator, there are many options.
May I ask why the chorus pedal isn't in the effects loop?
Check our our effects loops videos and signal path videos - it might shed light on the "why" part. 1) Typically you want pedals that can take line level - this is not one of those pedals typically. 2) Historically analog chorus wasn't use after the preamp, most of the iconic chorus sounds we know of were all in front of the amp effects, and depending on the design of the chorus will be betters suited level wise and impedance wise to be in series in front of the preamp, especially this pedal, the Arion SCH-1.
i found the Ai1 ( buffer in a jack ) and book marked it, need be .... pretty neat, but i don't run any time based effects at all, and i have an NS-1X
i even like my synths dry most of the time. ( the staples on drums, having more to do with texture and sustain )
i mean i will run a delay on a synth, on occasion, or a studio verb in a buss. but my guitar? no thank you...that's studio post, idk, i do think about it for some stuff...but it's just a pain.
my guitar is passive, but if i need a cable longer than 10' i will get a wireless ... but it's still nice to know of a consolidated solution like that, just in case....i haven't started on the bass rig yet.
Awesome video - thank you so much. Every pedal board video i have clicked on always has the power supply underneath. This was a really cool idea is there any pros/cons for above or below or is it just personal taste? :)
I could be wrong, but it looks like they built on a flat board, which doesn’t give much room underneath to run anything. I had to do this on a couple of my personal boards because they were completely flat too.
For me, it just fit better in a road case then a slanted board did
There can be problems with the power supply under the board if it's a linear power supply versus a switch mode. Most people don't understand this and think that their pedalboard manufacturer has sorted this for them, when in fact, the pedalboard company has no idea about magnetic leakage for EMF and how a linear power supply under your pedals can be a real noise issue. We have several videos on this including a power supply buyer's guide which spells a lot of this out.
What are your thoughts on the built-in buffers on the RJM PBC10? Are the Mesa high wire or the do-it-yourself buffer better options in your opinion? Thanks!
Good, I wish the input impedance was at 1M but that an easy mod.
ISO: Arion SLF-1 battery cover. I have the pedal would love to get a broken SLF-1 just for the bat-cover.
You can buy covers from All Parts
Hi ! I saw the 4 cable method interguvernamental . Can it be used with an amp without fx loop? Thanks
As shown in the video and in the diagrams of the DIY interface/buffer it can be used in mono (2 cable method), or with an effects loop (4 cable method). The video shows diagrams of this as well as the diagrams in the links in the description.
The background music in the beginnin' of this video, is that some unreleased track by Dann Huff?
Yes, indeed!
Great work mr Marangella!!! Can I ask you a question?? What isbthe name of that first interface that allows you to go both send/return or guitar/amplifier ?? You made it ?? Thanks
We made that custom, you can see our DIY buffer interfaces on CZcams. We show you how to make them yourself :)
Hey Mason, question. When you showed the image of the square plugs there was also a shallow straight plug shown. Where can I get some of those for my own pedalboard upgrade?
Squareplug SPS4 - still the same brand just different model.
@@VertexEffectsInc ah so I just missed it when I looked the first time. I'll go look again, thanks!
Clocked based effects like delays in the effects loops can cause ticking noise issues because the logic ground and the chassis ground of the switching power supply aren't suppose to be tied connected together. If you look at the manuals on switching power supplies it will say not to connect or LOOPING the field ground/chassis ground with the logic ground. The amplifiers effects loops send jack and return jack grounds are at a different ground potential than the delays DC jack ground and the switching power supply ground. What I'm saying is that all 3 jacks ground are not at zero volts. The manuals for various switching power supplies will say LOOPING the field ground/chassis ground with the logic ground will cause interference issues. LOOPING is tie/connecting the audio grounds, analog grounds, digital logic grounds to the chassis earth ground. Often you have to open up the clock based guitar pedal and FLOAT the digital logic ground from the DC jack to prevent it leaking the clock and digital noises from bleeding leaking into the chassis ground. I just don't understand these EE designers that make clock based digital effects because their "grounding Schemes" are all over the places and will not work good with certain switching power supplies and various amplifiers effects loops.
This is partially true, but still has a lot of holes in it. You're basing this on an incomplete understanding of grounding and noise, especially as it relates to pedals and DC. You're also taking switching supplies and applying that to digital clock noise. These are not the same. Switching supplies are generating the 9V for your pedals, the digital clock noise is internal to the pedal. Properly designed devices with switching supplies and digital clocking can work perfectly with no noise problems. A common way this is done is having a ground connection between analog and digital at some point. Proper ground PCB widths, locations compared to sensitive circuitry (capacitive coupling of hi-frequency noise), hi frequency filtering locations to ground, and termination are critical to keep the noise out. Also in terms of your points, (1) when you write “zero volts”, that is really DC and does not apply here. The grounds are never at the same potential at the circuit end ground as there is inductance in the ground that is really a resistance to high frequencies back to the common ground point, so noise voltage is dropped across this ground. (2) When you talk about "looping," this is for AC powered devices only, and what this really means is not adding another ground between signal (field) and earth as it creates a ground loop that will pick up switching noise. This does not apply to pedals, the switching supply is supplying the 9V, they are not internal on the digital devices. Also there are many legal requirements for power supply switching noise to not pollute the AC power line. (3) In terms of "floating" the digital logic ground, I'm not sure what you're saying here. I would not think you can disconnect a ground connection internally and the device keep working properly or have even a worse clicking problem. (4) with respect to having an EE degree, at best, most of us - including me - are at a service technician level by "real" engineering standards. Most real electrical engineers aren't working in the guitar pedal/amp/accessories field. This includes all of the iconic and idolized guitar pedal makers overwhelmingly.
@@VertexEffectsInc 1.) For guitar pedals that use AC power supplies. example like my digitech Jimi Hendrix experience modeling pedal uses an AC to AC wallwart power supply, its not AC to DC its AC to AC. All AC power supply guitar pedals should use an "isolation transformers" to prevent ground looping from the field ground to the earth ground. Guitar Amplifiers will cause "ghosting notes" from the AC 60hz bleeding leaking into the B+ Negative Bias voltage or high voltage rails. The same problem will happen with AC guitar pedals that use AC voltages because the 60hz will leak into the clock ground and audio ground causing noises and problems. 2.) The Reference should be earth ground which is "zero volts". The Switching power supply should be the reference on the primary side earth ground plugged into the AC wall outlet should be zero voltage. The guitar pedal board has all the guitar pedals plugged into the switch power supply DC jacks but the ground on the DC jacks is "Not zero volts reference back to earth ground" as well as the guitar amplifiers input jack ground reference back to earth ground as well as the guitar amplifiers effects loop jacks ground reference to earth ground aren't zero volts. The "Noise Voltage" is the main issue is measuring the Noise Voltage from the power supply DC jack ground to the guitar amplifiers input jack ground to the guitar amplifiers effects loop jack ground, which will have a different Noise Voltage Peak to peak voltage for just Noise, hum, interference, etc. Since you have a potential difference for all the grounds from the switching power supply DC Jacks ground, guitar amplifiers input ground, guitar amplifiers effects loop ground, and guitar pedals DC jack ground, which all aren't at "zero volts" you will have a Noise voltage reference back to earth ground. All guitar pedal designers for all different brands internally inside the guitar pedals audio ground, digital ground, clock ground, analog ground will NOT be all tied together at earth ground zero volts. It depends on the circuit design and who is designing the circuit boards but this is why you will get noise voltages, bad audio signal to noise ratio, clock tickling noises, etc. When using Clock based guitar effects in the amplifiers effects loop will cause the clock noises and clock clicking ticking noises to be louder is because the guitar pedals digital ground and clock ground are at a different potential than the guitar amplifiers input jack ground and guitar amplifiers jacks effects loop ground will be worse having a larger noise voltage. The guitar amplifiers effects loop jack ground is always at a different potential than the guitar amplifiers input jack. You can use an isolation transformers but his is just adding a band aid to the root cause problem. 3.) Since most guitar pedal designers and pedalboard Designers aren't EE engineers this is why all the grounds aren't at the same potential causing Noise Voltages on the audio ground, digital ground, clock ground, guitar amplifiers input jack ground, guitar amplifiers effects look jack ground, guitar pedals DC jack ground, etc. You have to take it to a specialized EE engineers that specializes in grounding Schemes. The new paul reed smith jimi Hendrix amplifiers is based on the marshall plexi but the Engineer added a new grounding scheme to cut down on the Signal To noise Ratio because the grounding scheme of the marshall plexi had all the grounds at different points causing very bad signal to noise ratio issues. Its all about the ground scheme. If you measure a "millivolt drop" from any ground to earth ground you have leakage current and Noise voltage, this is bad not good.
Very nice mason.
Thank you! Cheers!
Hi Mason, great video as always, have a question?? I’m using a Boss ES8 Loaded with pedals on al the loops but delay and reverb are separated into the amp loop, Boss ES8 already have dual buffers, I want to build an interface like the one you just show, but do I needed with all the buffers??
The ES-8 Does have buffers for input and output - however they're the standard Boss variety - not high quality, more middle of the road, and not particularly great line drivers or do well with a lot of capacitance seen on their output. If you want the most neutral sound, I'd recommend looking at our recommended buffers in the description or go the DIY route like we did with Lindsay.
@@VertexEffectsInc ok, so using the ones you recomend, the ones on ES8 should be off at all times??
@@tonygamez8895 correct
Is it posible to make an 4 Cable Method (FX Loop) and ad tuner output? If i go for a bigger house?
Sure...you can parallel off the input buffer...we have diagrams for it on our DIY Buffer Videos.
Nice tasty gain staging there!!
For sure, Lindsay curated a great list
What travel cases have people found best for the vertex pedal boards? Any input is appreciated.
If you go to the website, we list several compatible cases with every single model of Pedalboard
Awesome thank you much
Mason's the G.O.A.T.
Also, Lindsey is a HELL of a guitar player omg
She's the GOAT :)
Lindz.. you have to get the Fab Suisse... and you'll be able to do away with those pedals...Its the most underrated and well built pedal...
Thanks for watching!
Im just in love with the videos, the pedals, have an ultra phonix doing all my drives sounds, but i find a little anoying refering yourself as the "A.K.A the rig doctor", A.K.A ussually its used when someone else is presenting you, not yourself hahaha
Glad you dig the videos. This is the first I've head of it, but if I see the feedback continues that aligns with your grievance, perhaps we'll modify it. It's intended to be playful, not provocative.
Can anyone tell me what the song playing in the background at 3:41 is?
Dann Huff? Giant?
What are the dimensions of the board?
I think it was 24" x 12" or so...don't recall as we did it custom before we had our production pedalboards.
is that arion sch-1 chorus runing on 12v?
No, 9VDC
@@VertexEffectsInc thanks, cheers!
💘 🎸 Lindsay 🎸 💘
Heck yea!
Can you tell me the artist of the first song played in this video ? BTW I just love watching your videos
Not sure...might have been improvised by Lindsay!
you should talk to the bassist of covet , he has such cool sound backing the band , and so many pedals , yet all such a bess
Nice...we'll check it out!
@@VertexEffectsInc loook at their rig rundown , rat's nest
@@VertexEffectsInc you should maybe talk to the lap steel player of Larkin Poe, she has a very unique sound that’s easy to identify; she may not have the largest pedal board, but it seems big enough that you could beautify it for her.
@@jennifer6833 I'll check her out! Thank for the recommendation!
@@AJbassist we all gotta start somewhere
Finally Marty got his pedalboard done by Mason! (Did this joke got old yet?)
Thanks for watching
Whats the Name for that interface?thanks
see links in the description...it's one of DIY buffer interface boxes. Full diagrams and parts list included so you can replicate this yourself.
i guess i think about effects as cluttering my mix, more than not ... i mean i do use effects in the studio, because otherwise there would be no ambiance at all.
but live?....that's a space .... whatever it is.
but signal processing, yeah...that's what my board is, and that's all it needs to be for me.
i mean everyone thinks like that to some degree, and that's your wet dry blend........i just like it on zero, and that it reduces the clutter is the bonus there.
I’m really open to anything, Jazz, melodic death metal, prog, classic, pop, you name it, but country meh… Lindsey Ell is probably the first country/pop artist in my whole life that has made me come from under the rock a lot of guitarist grow under to appreciate something new :)
Lindsay is great!
Hey how’s it going? How do you feel about the Aetos power supply?
See our video on power supply buyers guide. All is explained.
@@VertexEffectsInc ok thanks
Did hendrix used buffer? Or brian may? Or early guitarist?
Jimi Hendrix used fairly long, coiled cables that certainly introduced significant capacitance and warmed up his tone considerably. This was likely desirable when you consider how bright a single-coil pickup into a cranked Marshall amp can be.
Any pedal "on" is a buffer.
Ok but what kind of cases are customers putting these boards in AND will you ever sell cases with your boards?
Andres - Pelican, SKB, and Gator all make great cases that we designed our boards to fit. I don't have plans to make a case, the reason being - I can't make the quality of cases that Gator, SKB, or Pelican can make for the price they can make it. I'm not a case manufacturer. Companies that do this (make cases with their pedalboard), are typically poorly made, not reliable, and often can't last a tour. I'm not arrogant enough to presume I can out-case the "Case Guys".
@@VertexEffectsInc thanks Uncle Mason! I’m really digging your board and after downsizing to a PT NANO+ I think I’m ready to go up a bit thanks to the nifty leveling feature you have that also allows for storage underneath the riser. Can’t wait!
ceriatone!
Good budget Dumble tones
🥰
Thanks for watching!
Why power grip, over dual lok?
Maybe that’s her personal preference? I dunno; hopefully he’ll answer.
Dual Lock is great. I moved to Power Grip - which we have a signature version on www.therigdr.com. I prefer it because 1) it's better in heat in humidity and doesn't lift off the board, and 2) it is stronger that SJ3550 or SJ3551 using less of it, which ends up being less expensive, cheaper to the customer, and it's overall better adhesive.
@@VertexEffectsInc thanks Mason! Getting ready to put a new touring board together. #sheilastephen
@@greglockhart7439 great! It's good stuff! Don't get me wrong if you have Dual Lock, use it, but I prefer Power Grip
@@VertexEffectsInc is Power Grip also a 3M technology? I’ve had some of the adhesive from Dual Lok come loose. I think it’s me trying to be thrifty with the DualLok Something that allows me “to use less” is GREAT.
I need to build one of your interface boxes sans buffers. I already have quality buffers. I took your advice from the video you did…has it been 6 years ago?
Maybe you should start making colored pedals? I’m too old for pink but purple!
Rock on... :0
Heck yea!
Finally Linsey get pro level build!!!! 😁.. one can only hope Tom Morello come to uncle mason and upgrade his 90s pedalboard 😁🤭
Maybe one day!
She's so cool and talented. God bless her ❤️🙏💯👍👌
She's the best!
music...0:15 ..name?
Dann Huff, Giant demo track.
@@VertexEffectsInc It's true. From the video class where he teaches the solo of "Stay". I knew I had heard that sound before. Thanks
Why did she get rid of the Wah pedal? And also, why did you put the power supply on top? You could have hidden it on the bottom to add more room for another pedal.
Wah was never part of the rig or part of our conversations - perhaps it's more of a fringe application for her and can easily be placed next to the board as a wah is almost always first in the chain following the guitar. Just a guess. As for the power supply, generally, if you're using most linear isolated power supplies, the supply under the board isn't a good idea as you're putting your pedals in the magnetic field of the transformer and the leakage on most of the is pretty bad, especially with a lot of high current pedals where you're getting close to the current max total of the supply. Most of these higher current linear supplies don't have any shielding by way of the case because they use aluminum to keep the weight down and to use the chassis as a heatsink. This isn't ideal. Now with switch mode supplies, it's not so much of an issue but not all brands of power supply do switch mode yet. Furthermore, the Pedaltrain or similar style boards with the power supply underneath is nice for those that want a modular board and are hobbyist level players that like to experiment. However, for a more sedentary professional rig, it's more road worth and easier to trouble shoot when everything is top mounted. This is primarily why you seen most pro rig builders using this style flat board surface to make it all visible and easy to isolate cables or problematic areas which are inherent in touring.
yeh mason is gods gift to guita players
LOL!
7:48 why the hell is there two tuners lol
where do you do you see two?
7:48 on her previous board. there’re boss tuners at the right and left side of the board
@@VertexEffectsInc nice vid btw
The second one isn’t hooked up
It's good to have a spare tuner, in case the first one breaks.
Did anyone hear that yell around the time she is talking about the centura?
Huh?
@@VertexEffectsInc listen for it, you can hear it in the background
yup! i heard that. it’s all throughout the pedalboard demo. 😉
I think it's the leather of her trousers rubbing against the seat.
I always thought she was from Calgary Alberta Canada....???
She is from Calgary.
why she used fx loops when the amps set on clean ???
ummm.. clueless a little? is my guess
The amp in the demo was, but that was our amp, not hers. She uses a channel switching Dumble style amp so the effects loop is valuable when you have amp gain.
Also remember the pedalboard can work with all pedals in series with a clean amp or 4 cable method for an effects loop.
Is she Canadian? I think I know that name. Thanks.
Yes she is!
Can she play highway star on a kitchen table ?
Huh?
please build my board someday 🥺 haha
Thanks for watching!
9:23 Wait what? You've only played trough your own signature pedal a couple of times? They kinda just got you to sign your name on the pedal? I thought you were a part of the design and all... bummer :( About to buy the pedal. Still gonna get it cuz it sounds amazing, but still... a bit of a kick to the nuts
It was more about the build, not the pedal demos specifically.
It’s funny if you heard this girl on the radio you would have no idea she can play like that.
Yeah I didn’t know she could play until my guitar teacher google her
Lindsay is amazing! Great player for sure!
What's the deal? They get a free pedal board build if they put a vertex pedal on the board?
Huh?
$25 for 1 little patch cable ...Wow. crazyness..robbery and greed. no cable is worth that...
You must be new here - we have video tutorials showing you how to make the exact same cables that we sell, same materials, all the same vendors, part numbers, etc. This allows any viewer to replicate exactly what I’m doing for a fraction of the price. If they don’t want to make the cables themselves, we have an option for that too and offer a lifetime warranty on the cables. I’m not sure how to be any more transparent or democratic about it. Here’s the video for you showing how to DIY it: czcams.com/video/Z88EXSn9QY8/video.html
She's from Canada, not Nashville. Another one ashamed of her True North heritage.
I think she's located there now - not sure that's a slight on Canada.
I'd be upset if I were sold a shirt with the shoulder missing.🤠
Guitar picks are for posers. 🤡
Ha!
I’m really sorry to say but what is so special about this board build? Don’t get me wrong it’s nicely organised and looks quite neat but that’s it. In a live setting i also think the second pedal row is not accessible enough. There’s nothing smart about this board in the way that you have a new switching or powering solution. You do not use any space underneath. What you see is what you get. That’s not a bad things so don’t get me wrong but personally I just don’t understand the need for a professional here. It’s not monstrous midi rig that’s so complicated that you need a science degree, it’s just a few pedals lined up nicely. I’m not a professional in any means but I still build my own pedalboards every once in a while and personally I would have the ambition to figure out a way to make this more than just a row of pedals. Maybe I would try to figure out how to make it more space efficient, how to make it more gigable by adding an easy programmable Switcher or something like that. Again this probably gonna be rock solid and will survive any gig, but I don’t think that’s enough for a professional build. Not trying to throw shade, just trying give some food for thought.
Second pedal row is on a riser, so it sits 1" higher than the first row, pretty sure this is discussed in the video. Typically I don't recommend for a pro level rig to go under the board for power, it complicates trouble shooting and is no the standard among pro rig builders from Robert Bradshaw, to Dave Friedman, etc., it's not unique to me. You can get a Pedaltrain and DIY if you'd like to do that - and that's fine, but that's not the assembly standard. You don't see the need, but perhaps Lindsay, among touring 200 dates a year, doesn't see the value in doing it herself. It's like you're criticizing the video about something that it's not - a rig built for you.
She's a really cool player. And that board is obviously very clean. But the tones are terrible.
I was digging em!
All sounded great to me.
Tight pedalboard,....wasted....
Huh?
I'm not impressed!
Now we know 😉